
Fonte 1000W - EletronicaPotenciaI
VictorMichels/Kicad-1000W-Thyristor-Controlled-PSU
Tested and working schematic and PCB layout design for a single-phase semi-controlled full-bridge rectifier

ESP32-C3 PCB control system with Nextion HMI, motor, sensor and power-driver interfaces.
Hardware deneme is an open-source printed circuit board by KerimAltuntecim, from the KerimAltuntecim/esp32-pcb-control-system repository on GitHub, published under the MIT licence. It is a 2-layer board with 38 parts on 110 nets, routed with 119 tracks and 0 vias.
It is built around the ESP32-C3-WROOM-02-H4, IR2103PBF and MOC3022M, with the ULN2003 and IRF540N among its other parts. Its parts include 16 connectors, 10 resistors, 6 ICs, 2 transistors and 1 diode. It belongs with the robots and motor control boards and the ESP32 and RISC-V boards of this library.
English summary: ESP32-C3 based control PCB prototype with Nextion HMI, stepper, sensor, relay, triac and MOSFET interfaces. The repository documents the hardware and firmware structure; it is not a production-certified design.
ESP32-C3 tabanlı, Nextion HMI ekran üzerinden kontrol edilen çok işlevli bir PCB prototipi. Kart; sensör okuma, motor sürme, röle/triyak/MOSFET çıkışları ve kullanıcı arayüzü haberleşmesini tek bir donanım üzerinde birleştirir.
Nextion ekran üzerinden aşağıdaki menüler tasarlanmıştır:
ESP32 firmware’i Nextion’dan gelen role, tri, fet, rgbr, rgbg, rgbb, sens ve step komutlarını işler. kerim.HMI, arayüzün düzenlenebilir Nextion Editor kaynak dosyasıdır.
GitHub web yüklemesi nedeniyle dosyalar depo kökünde açıklayıcı öneklerle tutulur:
firmware__...: ESP32 Arduino firmware’ihardware__...: KiCad şematik, PCB ve proje dosyalarınextion__...: Nextion HMI kaynak dosyasıimage__...: PCB, şematik ve arayüz görselleriBu çalışma ilk el montajı yapılmış bir prototiptir; seri üretime hazır ürün olarak değerlendirilmemelidir. Firmware’in bazı bölümleri donanım üzerinde yeniden doğrulanmalıdır. Triyak ve MOSFET kontrol seviyelerinin gerçek yükteki etkisi, bağlı yük tipine ve güç katı ayarlarına bağlıdır. Batarya ADC ölçümü bu firmware sürümünde aktif bir özellik olarak kullanılmamaktadır.
Triyak/röle tarafında şebeke gerilimi bulunabileceğinden test ve kullanım sırasında uygun elektriksel izolasyon ve güvenlik prosedürleri uygulanmalıdır.
MIT License ile yayımlanmıştır.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 670 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R4, R5, R6, R7 |
| 4 | Screw_Terminal_01x02 | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J1, J2, J5, J6 |
| 2 | PC817 | Package_DIP:DIP-4_W7.62mm | U1, U2 |
| 2 | Screw_Terminal_01x04 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-4P_1x04_P2.54mm_Horizontal | J4, J14 |
| 2 | Screw_Terminal_01x08 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-8P_1x08_P2.54mm_Horizontal | J15, J16 |
| 2 | Screw_Terminal_01x15 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-15P_1x15_P2.54mm_Horizontal | J3, J7 |
| 2 | lamba | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J8, J11 |
| 2 | şebeke | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J9, J10 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 170k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9 |
| 1 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 22 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R8 |
| 1 | 330k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R10 |
| 1 | BT136-500 | Package_TO_SOT_THT:TO-220-3_Vertical | Q2 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_15x7.5RM7.6 | BZ1 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U6 |
| 1 | IR2103 | Package_DIP:DIP-8-16_W7.62mm | U4 |
| 1 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | MOC3022M | Package_DIP:DIP-6_W7.62mm | U7 |
| 1 | Pololu_Breakout_A4988 | Module:Pololu_Breakout-16_15.2x20.3mm | A1 |
| 1 | SANYOU_SRD_Form_C | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | K1 |
| 1 | Screw_Terminal_01x03 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-3P_1x03_P2.54mm_Horizontal | J12 |
| 1 | ULN2003 | Package_DIP:DIP-16_W7.62mm | U3 |
| 1 | batarya | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J13 |

VictorMichels/Kicad-1000W-Thyristor-Controlled-PSU
Tested and working schematic and PCB layout design for a single-phase semi-controlled full-bridge rectifier


david8128/Electeam-Sharky
Firmware designed in ESP32 DEVKIT microcontroller where motor, throttle, breaks, Nextion touch screen and more systems are integrated.


SalihAyvaci21/ESCTasarim
Drone motorları için geliştirilmiş; ATmega328P ve IR2103 tabanlı, sandviç PCB yapısına (2x2 katman) sahip, IRLZ44N MOSFET'li yüksek akım 3-faz BLDC motor sürücüsü.



38 parts, built around the ESP32-C3-WROOM-02-H4, IR2103PBF, MOC3022M and ULN2003. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the KerimAltuntecim/esp32-pcb-control-system repository on GitHub, at the commit this page was made from: the board is hardware__deneme.kicad_pcb and its schematic hardware__deneme.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).