Skip to the content
2 layers25 × 25 mmPlaca Carga, the printed circuit board in 3D

Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

Size
25 × 25 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
13
Pads
40
Tracks, vias
70, 0
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 May 2022
Updated
29 Oct 2026

Overview

Placa Carga is an open-source printed circuit board by danielvie, from the danielvie/doutorado repository on GitHub. It is a 2-layer board of 25 × 25 mm with 12 parts on 13 nets, routed with 70 tracks and 0 vias.

It is built around the LM324. Its parts include 8 resistors, 2 capacitors, 1 IC and 1 connector.

Main components

1

README

README.md

Doutorado

Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

Quick links

Where to go

NeedGo to
Thesis and paper LaTeX sourcesLATEX/
Plans, TODOs, and qualification materialresearch-material/planning/
Reviewer commentsresearch-material/review-feedback/
Authored analysis and meeting notesresearch-material/working-notes/
Shared diagrams and writing assetsassets/
Current MATLAB simulations/control codesimulations/matlab-sim/
Older MATLAB simulationssimulations/legacy/
Projection/feasibility-region MATLAB worksimulations/projection/
ESP32 firmware, hardware docs, and web UIembedded/
External papers, books, theses, and course materialresearch-material/literature/
Presentations and slidespresentations/
External/vendor materialz_dependencies/, z_kawa/, z_mpt_install/, and z_qpoases/

Common commands

This repository uses Taskfile.yml:

sh
task --list

Important tasks:

  • task run opens generated overview documentation.
  • task test validates generated overview documentation.
  • task clean removes generated overview documentation.
  • task update-tese copies LATEX/thesis/build/tese.pdf to the repository root.

Navigation conventions

  • Start from this README, then use docs/REPO_MAP.md for locations and CONTEXT.md for terminology.
  • Prefer area-specific READMEs/docs when they exist.
  • Treat z_dependencies/, z_kawa/, z_mpt_install/, z_qpoases/, and simulations/backup/ as backup, vendored, or auxiliary material unless a task explicitly points there.
  • Prefer simulations/matlab-sim/ over simulations/legacy/ for current simulation work.
  • Prefer embedded/esp32_idf/ for current ESP32 firmware work.
  • Avoid adding new loose files at the repository root; put new material in the closest project area.
  • Keep document navigation folders at most three levels deep. Self-contained source/build trees are exempt when flattening would break them.

Parts

12
QtyValueFootprintReferences
410kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR3, R4, R5, R6
21uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC6, C7
115kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR8
133kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
156kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR7
15k6Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR9
1Conn_01x06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ1
1LM324Package_DIP:DIP-14_W7.62mmU1

More from danielvie/doutorado

2
  • 2 layers140 × 77 mmPlaca Mae, the printed circuit board in 3D

    Placa Mae

    danielvie/doutorado

    Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

    30 parts
  • 2 layers75 × 44 mmPlacaESP, the printed circuit board in 3D

    PlacaESP

    danielvie/doutorado

    Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

    17 parts

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers36.8 × 34.7 mmTinylab proto1, the printed circuit board in 3D

    Tinylab proto1

    espotek-org/Labrador

    EspoTek Labrador is a USB device that transforms your PC or smartphone into a fully-featured electronics lab. This repo holds all of the source code!

    79 parts1.2k
  • 4 layers82.6 × 82.5 mmJumperless2, the printed circuit board in 3D

    Jumperless2

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    208 parts914
  • 2 layers231.1 × 106.7 mmSnark barker, the printed circuit board in 3D

    Snark barker

    schlae/snark-barker

    A 100% compatible replica of the famed SB 1.0 sound card

    199 parts687
  • 4 layers82.6 × 82.6 mmJumperlessV5r8, the printed circuit board in 3D

    JumperlessV5r8

    Architeuthis-Flux/JumperlessV5

    The next generation jumperless breadboard

    650 parts332
  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 2 layers191.5 × 76 mmPcb project, the printed circuit board in 3D

    Pcb project

    CrashOverride85/zc95

    4 channel EStim box inspired by the mk312bt, with Lua scripting support

    337 parts117GPL-3.0
  • 4 layers292.1 × 88.3 mmSnark barker mca, the printed circuit board in 3D

    Snark barker mca

    schlae/snark-barker-mca

    A Sound Blaster compatible sound card for Micro Channel bus computers

    177 parts69

Questions

How big is the Placa Carga PCB?

It measures 25 × 25 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Placa Carga use?

12 parts, built around the LM324. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Placa Carga KiCad files?

From the danielvie/doutorado repository on GitHub, at the commit this page was made from: the board is embedded/kicad/PlacaDaniel/Placa_AmplificadorInstrumentacao/Placa_Carga.kicad_pcb and its schematic embedded/kicad/PlacaDaniel/PlacaESP_Rev3/PlacaESP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Placa Carga design in my own project?

Its repository states no licence, so its author keeps all rights: ask danielvie before reusing the design.