Skip to the content
2 layers119.4 × 165.1 mmProtoMate, the printed circuit board in 3D

Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

Size
119.4 × 165.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
49
Nets
49
Pads
188
Tracks, vias
589, 114
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 Oct 2026
Updated
8 Nov 2026

Overview

ProtoMate is an open-source printed circuit board by daleondev, from the daleondev/ProtoMate_Control repository on GitHub. It is a 2-layer board of 119.4 × 165.1 mm with 49 parts on 49 nets, routed with 589 tracks and 114 vias.

It is built around the 2N2222A. Its parts include 23 resistors, 12 connectors, 6 capacitors, 6 transistors and 2 ICs.

Main components

1

README

hardware/perfboard/README.md

ProtoMate stepper perfboard

Open ProtoMate.kicad_pro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

The controller is the Arduino GIGA R1 WiFi / STM32H747XIH6. Its M4 owns motor generation, feedback, reference switches and driver diagnostics. The physical perfboard uses four cable harnesses to the GIGA; it is a separate board, not the display shield. Controller destinations use the Arduino's printed D/A labels, checked against the official pinout and the repository's current CubeMX configuration.

Power the GIGA independently through USB-C. Its 3V3 output feeds J101.8; ground is common with the perfboard. Do not connect the buck's 5 V output to GIGA 5V, VIN or USB. The buck powers the DM542T signal interface and the encoder's 5 V circuitry; 24 V supplies the three motor drivers.

text
hardware/perfboard/
├── ProtoMate.kicad_pro       Project settings and electrical checks
├── ProtoMate.kicad_sch       Root sheet: controller, power, sheet navigation
├── ProtoMate.kicad_pcb       47 × 65 hole perfboard placement and hand wiring
├── sheets/                  Motor interfaces, encoder, headers, switches
├── libraries/               Project-local symbols, footprints and buck 3D model
├── sym-lib-table            Relative symbol-library registration
├── fp-lib-table             Relative footprint-library registration
├── assembly/                Build instructions, parts, hole/wire/harness tables
├── exports/                 Schematic/assembly PDFs and verification reports
└── tools/                   Repeatable checks and export command

Schematic and layout relationship

The root schematic links five child sheets: M1/DM542T, M2/M3/TMC2209, M1 encoder, perfboard cable headers, and reference limit switches. Global net names connect these sheets electrically. The connector sheet defines J101–J107 and J113, and the reference-switch sheet defines J108–J111. J104 is the ten-way DM542T screw terminal for control, ALM and 24 V power. The M1 sheet defines pull-up R30; J101 carries ALM to the GIGA. All connector pin numbers match the layout and harness table.

All 49 perfboard footprints have assigned library footprints and native links to their schematic symbols. These comprise Q1–Q6, R1–R12, R20–R30, C1–C6, U2/U3, J101–J111 and J113. R10–R12 remain on the layout and are marked DNP.

The buck U1 and Adafruit A3/A4 modules mount directly at J103/J105/J106. These footprints represent their soldered mounting pins and full module outlines. The module symbols remain excluded from separate PCB placement: the barrel jack and four-way motor terminals remain on their modules. J103 has four electrical contacts: 5 V output, output ground, VIN ground and 24 V input. J105/J106 each have ten JP4 control pins plus two JP1 power pins. J104.9/10 provide the DM542T power connection and the two power-distribution star joints. Dedicated underside supply/return branches feed each TMC module through its local C1/C2 bulk capacitor connections. Motor winding cables connect directly to the drivers. The GIGA, DM542T, motors and switches remain external. The buck's 63 × 27 mm body follows the supplied STEP model; its nominal mounting grid is 5.08 mm within each pair and 50.8 mm between pairs. Its barrel jack receives 24 V at the left edge.

J113 uses eight contacts for six signals and two shared ground returns to the GIGA: TX (PD5), RX (PD6), M2 DIAG (PC3), M3 DIAG (PC0), M2 INDEX (PB8) and M3 INDEX (PB9). R29 is the shared UART's 1 kΩ TX series resistor. J105/J106 pin 9 is UART, pin 7 is DIAG and pin 8 is INDEX. Address straps are M2 MS1/MS2 = GND/GND and M3 = 3.3 V/GND. Both SPRD jumpers stay open. Firmware configures current and 16 microsteps before enable; the potentiometers do not set current in UART mode. See the UART wiring instructions.

The .kicad_pcb is a map for a purchased individual-pad board: F.Cu represents top jumpers, B.Cu represents solder-side wires, and vias represent wire passages. Use the 65 × 47-hole board, oriented as 47 columns × 65 rows, A1–BM47, at 2.54 mm pitch. The outer hole centres span 116.84 × 162.56 mm; the nominal outline is 119.38 × 165.10 mm with half-pitch margins. J104 and both TMC modules sit along the top edge with their cable entries facing outward. J107 sits below J104, keeping both motor-1 cables together. J101, J113, J102 and J108 form a left-edge GIGA connector bank with 9.1 mm gaps between bodies and pin 1 at the bottom of every header. The encoder receiver and level converters occupy the centre-left; the DM542T transistor stages occupy the right interior. The buck sits at the bottom left, with the three switch cable headers at the bottom right. Q1–Q3 have 30.48 mm between stages; Q4–Q6 have 15.24 mm between stages. Decoupling capacitors stay close to their ICs. The barrel jack faces the left edge. The wire schedule specifies underside routes and insulated top crossovers through dedicated free holes. All wire ends are soldered underneath. J101's pin 1 is at Z4; odd pins run up column 4 and even pins up column 3. The 11 designated power connections all stay underneath and use 0.5 mm² insulated copper wire; wire drawing width does not specify conductor size. Use the assembly instructions to build it.

The STEP engine uses one 32-bit TIM2 with DMA: channels 1/3/4, all AF1, with a 10 MHz timeline. M4's runtime uses TIM5, TIM6 samples the encoder and TIM7 services STEP completion. The GIGA's own 16 MHz crystal provides the clock; there is no external ST-Link clock setting or board solder-bridge change.

SignalPerfboard contactGIGA labelMCU pin / function
M1 STEPJ101.1A7PA0 / TIM2_CH1
M1 DIRJ101.3D4PJ8
M1 ALMJ101.4A3PB1 / EXTI1
M2 STEPJ101.5D3PA2 / TIM2_CH3
M2 DIRJ101.7D6PD13
M3 STEPJ101.9D2PA3 / TIM2_CH4
M3 DIRJ101.11D16PH13
Shared enableJ101.12D15PC7; HIGH = disabled
Logic supplyJ101.83V3GIGA output
M1 encoder AJ102.1D7PB4 / TIM3_CH1
M1 encoder BJ102.3D5PA7 / TIM3_CH2
M1 encoder ZJ102.5D53PG7 / EXTI7
M1 referenceJ108.1D49PE4 / EXTI4
M2 referenceJ108.2D51PE5 / EXTI5
M3 referenceJ108.3D47PB2 / EXTI2
TMC UART TXJ113.1D18PD5 / USART2_TX
TMC UART RXJ113.3D19PD6 / USART2_RX
M2 INDEXJ113.4D8PB8 / EXTI8
M2 DIAGJ113.5A4PC3 / EXTI3
M3 INDEXJ113.6D9PB9 / EXTI9
M3 DIAGJ113.7A6PC0 / EXTI0

All nine controller ground returns join the GIGA's common GND. See Harness.csv for each return and the complete driver, module and switch wiring. The GIGA's QSPI flash is onboard and the filesystem uses internal flash; no external QSPI or SD wiring is part of this project.

R7's 470 Ω pull-up holds shared enable HIGH during reset. M2/M3 STEP have 10 kΩ pull-downs R8/R9; M1 STEP has a path to GND through R1 and R2. The firmware keeps STEP LOW and enable HIGH until motion is explicitly enabled. These physical bias paths depend on the perfboard and its GIGA logic supply being connected.

The reference switches connect to J109/J110/J111 (M1/M2/M3), pin 1 = REF and pin 2 = GND. COM–NC is closed when released: LOW is healthy/released; HIGH means pressed or an open cable. The GIGA supplies internal 3.3 V pull-ups and uses both-edge EXTI. The schematic names functional switch contacts; check the NC pair by continuity rather than relying on connector colours.

DM542T ALM+/ALM− connect to J104.7/8. R30 pulls ALM+ to 3.3 V through 4.7 kΩ; J101.4 returns it to A3/PB1. The normally conducting alarm is LOW when healthy and HIGH on fault/open cable. See the external connection instructions.

Controller harness

Use four short harnesses between the GIGA and perfboard: J101 (12 contacts), J102 (6), J108 (4), and J113 (8). Each signal appears exactly once; 3.3 V enters only at J101.8. J101 also carries the M1 alarm signal.

The nine ground conductors have deliberate roles: three STEP returns at J101, three encoder returns at J102, one shared switch return at J108, and two shared UART/diagnostic returns at J113. Twist each STEP and encoder signal with its assigned ground. Bundle the slower signals with their shared returns; keep these short local harnesses separate from motor and 24 V cables. The ground conductors may join at a ground bus beside the GIGA; they do not need separate GIGA GND pins. Use a short, solid connection from that bus to GIGA GND.

Module ground contacts and address straps remain connected as required by the modules. Motor supply current uses the dedicated power branches. Ground links in the perfboard wire schedule are required even where cable returns are shared.

Editing workflow

  1. Open the project above, then its schematic and PCB editors. Edit electrical connections and component assignments in the schematic.
  2. Save the schematic and use Tools → Update PCB from Schematic (F8). Keep UUID-based association; leave Re-link footprints to schematic symbols based on their reference designators unchecked. Review the proposed changes.
  3. Apply the update, then place new parts and adjust the hand-wire routes in the PCB editor. Use the 2.54 mm hole grid for leads and wire passages. F8 transfers connectivity and component changes; it does not design the new wiring routes.
  4. Maintain Wires.csv after routing changes and Harness.csv after cable/connector changes. Review mounting details in Parts.csv. Run the refresh command below before using or sharing the assembly documents.

Project-local footprints preserve the actual grid spacing and Diotec E/B/C pad identities. They resolve through ${KIPRJMOD}, so moving or cloning the repository does not require personal library paths. The X/Y axial resistor patterns describe the two existing orientations of the assembly drawing.

There is no separate netlist-import step or second electrical design to maintain. KiCad's schematic-to-board check verifies the association, footprint identity, value, and pad connectivity in the saved project.

Checks and exports

From the repository root:

sh
python3 hardware/perfboard/tools/refresh.py

Requires KiCad 10 (kicad-cli and its pcbnew Python module), Python 3 and Poppler's pdfunite. The command checks ERC, DRC with schematic parity, symbol links, pad nets, the hole grid, wire endpoints/connectivity, module body clearance, mounting contacts, dedicated power branches and harness destinations. All 20 motor, encoder, reference and driver signal contacts are checked against the GIGA schematic and external/CubeMX/CubeMX.ioc by default: MCU pin, peripheral, M4 ownership, firmware label, input pulls/edges, UART settings and disabled startup level. The checks also reject buck 5 V or external-storage connections on the controller. Use --ioc /path/to/GIGA.ioc to select another matching GIGA configuration. The command updates:

Use python3 hardware/perfboard/tools/refresh.py --check-only to refresh just the checks. The tool reads the native design; it never regenerates or overwrites its schematic or layout. Wire lengths and side choices in the assembly schedule remain manually reviewed when routing changes. The checks validate a wiring model, not solder joints or measured encoder-interface timing.

Manufacturing silkscreen and missing-courtyard checks are waived for this hand-wiring map. Electrical clearance, unconnected pads, schematic parity and local footprint-library consistency are checked. No fabrication outputs are generated.

Parts

49
QtyValueFootprintReferences
71kProtoMate_Perfboard:R_Axial_P10.16mm_XR1, R3, R5, R22, R25, R28, R29
610kProtoMate_Perfboard:R_Axial_P10.16mm_XR6, R8, R9, R21, R24, R27
62N2222AProtoMate_Perfboard:Diotec_2N2222A_EBC_P2.54mmQ1, Q2, Q3, Q4, Q5, Q6
44k7ProtoMate_Perfboard:R_Axial_P10.16mm_XR20, R23, R26, R30
3DNPProtoMate_Perfboard:R_Axial_P10.16mm_XR10, R11, R12
2100nProtoMate_Perfboard:C_Nonpolar_P2.54mmC3, C4
2100u / 50VProtoMate_Perfboard:CP_Radial_D10_P5.08mmC1, C2
210kProtoMate_Perfboard:R_Axial_P10.16mm_YR2, R4
21uProtoMate_Perfboard:C_Nonpolar_P5.08mmC5, C6
1470RProtoMate_Perfboard:R_Axial_P10.16mm_YR7
1AM26C32CN / DIP-16ProtoMate_Perfboard:DIP-16_W7.62mm_SocketU2
1DM542T control + ALM + power / screw 5.08 mmProtoMate_Perfboard:TerminalBlock_1x10_P5.08mm_DM542TJ104
1M1 NC switch / 1x02ProtoMate_Perfboard:PinHeader_1x02_P2.54mm_VerticalJ109
1M1 encoder / 1x08ProtoMate_Perfboard:PinHeader_1x08_P2.54mm_VerticalJ107
1M2 NC switch / 1x02ProtoMate_Perfboard:PinHeader_1x02_P2.54mm_VerticalJ110
1M2 TMC2209 direct mountProtoMate_Perfboard:Adafruit_6121_JP4_Power_DirectMountJ105
1M3 NC switch / 1x02ProtoMate_Perfboard:PinHeader_1x02_P2.54mm_VerticalJ111
1M3 TMC2209 direct mountProtoMate_Perfboard:Adafruit_6121_JP4_Power_DirectMountJ106
1Nucleo UART / DIAG / INDEX / 2x04ProtoMate_Perfboard:PinHeader_2x04_P2.54mm_VerticalJ113
1Nucleo encoder / 2x03ProtoMate_Perfboard:PinHeader_2x03_P2.54mm_VerticalJ102
1Nucleo motion / 2x06ProtoMate_Perfboard:PinHeader_2x06_P2.54mm_VerticalJ101
1Nucleo references / 1x04ProtoMate_Perfboard:PinHeader_1x04_P2.54mm_VerticalJ108
1SN74HC126N / DIP-14ProtoMate_Perfboard:DIP-14_W7.62mm_SocketU3
1U1 buck direct mountProtoMate_Perfboard:QIQIAZI_XY3606_DirectMountJ103

More from daleondev/ProtoMate_Control

5
  • 4 layers111 × 53.3 mmGiga adapter, the printed circuit board in 3D

    Giga adapter

    daleondev/ProtoMate_Control

    Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

    127 parts
  • 4 layers111 × 53.3 mmGiga adapter, the printed circuit board in 3D

    Giga adapter

    daleondev/ProtoMate_Control

    Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

    127 parts
  • 4 layers55 × 50 mmDisplay adapter, the printed circuit board in 3D

    Display adapter

    daleondev/ProtoMate_Control

    Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

    55 parts
  • 4 layers55 × 50 mmDisplay adapter, the printed circuit board in 3D

    Display adapter

    daleondev/ProtoMate_Control

    Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

    55 parts
  • 2 layers119.4 × 165.1 mmProtoMate, the printed circuit board in 3D

    ProtoMate

    daleondev/ProtoMate_Control

    Open ProtoMate.kicadpro in KiCad 10. The complete system schematic and linked perfboard layout share the same project name and component identities.

    49 parts

Similar boards

  • 2 layers101.5 × 83 mmSd2snes, the printed circuit board in 3D

    Sd2snes

    mrehkopf/sd2snes

    SD card based multi-purpose cartridge for the SNES

    154 parts722GPL-2.0
  • 2 layers279.4 × 203.2 mmZ180GDC, the printed circuit board in 3D

    Z180GDC

    lynchaj/rhyophyre

    Single Board Computer featuring Zilog Z180 processor and NEC µPD7220 Graphics Display Controller

    249 parts12
  • 2 layers99.1 × 99.1 mmQL Qsound10x10, the printed circuit board in 3D

    QL Qsound10x10

    alvaroalea/QL_QsoundQprint_clone

    A clone board of the Sound card for the Sinclair QL Computer.

    23 parts11
  • 2 layers156.5 × 67.5 mmNixieScanDisplay, the printed circuit board in 3D

    NixieScanDisplay

    profdc9/NixieClock

    A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.

    106 parts10
  • 2 layers89.3 × 50 mmMM58167-ISA RTC, the printed circuit board in 3D

    MM58167-ISA RTC

    jensma-de/MM58167-ISA-RTC

    RTC module for the ISA slot. With schematics, project files in kicad and open source software to drive the clock.

    29 parts9
  • 2 layers97.6 × 76.8 mm12f675-mppt, the printed circuit board in 3D

    12f675-mppt

    rasberryrabbit/PIC12F675MPPT

    Solar MPPT circuit.

    45 parts9GPL-3.0
  • 2 layers14.6 × 13.6 mmChip and transistor, the printed circuit board in 3D

    Chip and transistor

    gidim/e61-gauge

    An analog temperature gauge for E61 espresso machines. A custom PCB drives a VID6606 stepper motor gauge needle, reading temperature from an NTC thermistor.

    15 parts8
  • 2 layers147.2 × 58.3 mmLi IonBatteryProtection, the printed circuit board in 3D

    Li IonBatteryProtection

    cnobile2012/Li-IonBatteryProtection

    Circuit to protect Li-Ion and Li-Po batteries at the cell level.

    81 parts6MIT

Questions

How big is the ProtoMate PCB?

It measures 119.4 × 165.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ProtoMate use?

49 parts, built around the 2N2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ProtoMate KiCad files?

From the daleondev/ProtoMate_Control repository on GitHub, at the commit this page was made from: the board is backups/h753/hardware/ProtoMate.kicad_pcb and its schematic backups/h753/hardware/ProtoMate.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ProtoMate design in my own project?

Its repository states no licence, so its author keeps all rights: ask daleondev before reusing the design.