2 layers92.2 × 64.5 mm
2 layers167.9 × 105.9 mm
Ignition
cuspaceflight/OkGo3Rocket motor ignition and valve control from far, far away
- Size
- 167.9 × 105.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 112
- Nets
- 63
- Pads
- 369
- Tracks, vias
- 1,402, 182
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 25 Nov 2012
- Updated
- 31 Aug 2017
Overview
Ignition is an open-source printed circuit board by cuspaceflight, from the cuspaceflight/OkGo repository on GitHub. It is a 2-layer board of 167.9 × 105.9 mm with 112 parts on 63 nets, routed with 1,402 tracks and 182 vias.
It is built around the STM32F071CBT6, RFM95W and BSS138BK, with the MBR2H200SFT1G among its other parts. Its parts include 33 resistors, 19 diodes, 12 capacitors, 12 connectors and 6 transistors. It belongs with the STM32 boards of this library.
Main components
4
STM32F071CBT6
LQFP-48(7x7)-40℃~+85℃ 1.65V~3.6V 128KB 12bit 12bit 16KB 32 Bit 37 48MHz ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)RFM95W
SMD-16PUncategorisedHopeRF Micro-electronics
BSS138BK
SOT-23-55℃~+150℃ 1 N-channel 1.6V 1.6Ω@10V 350mW 360mA 56pF 60V 700pC@4.5V N-Channel SOT-23 MOSFETs ROHSNexperiaMOSFETs
MBR2H200SFT1G
SOD-123-55℃~+150℃ 1 Independent 200V 200uA@200V 2A 30A 940mV@2A SOD-123 Schottky Diodes ROHSonsemiSchottky Diodes
README
README.mdOkGo
OkGo is Cambridge University Space Flight's rocket firing controller.
OkGo was designed for testing the Quasar hybrid rocket motor. It allowed remote (over 100m of wire) control of the nitrous oxide valve and firing of the ignition e-match. It was constructed using an ad-hoc point-to-point layout. An entirely passive design, it simply uses mechanical switches to trigger relays. It was later upgraded to control two valves, one of which passed a low flow of nitrous oxide to help start the motor.
OkGo 2 was a full redesign for the launch of Martlet 2. Due to the increased safety radius (on the order of 500m) radio control is to be used. It will have 4 general purpose (valve or e-match) channels with independent continuity checking and firing, and separate firing boxes containing current limiting resistors.
OkGo 3 is another full redesign for the launch of Martlet 3. It will continuity check and ignite a single channel with a constant-current drive. Ignition and control will be small and light for portability.
Parts
112| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100k | Resistors_SMD:R_0805 | R106, R202, R204, R210, R214, R220, R224 |
| 6 | 180R | Resistors_SMD:R_0805 | R105, R201, R208, R213, R218, R223 |
| 6 | BSS138BK | Housings_SOT-23_SOT-143_TSOT-6:SOT-23 | Q101, Q201, Q202, Q203, Q204, Q205 |
| 6 | TVS_small | Resistors_SMD:R_0603 | D101, D103, D206, D210, D214, D218 |
| 5 | 100n | Capacitors_SMD:C_0805 | C101, C102, C104, C105, C109 |
| 5 | 10k | Resistors_SMD:R_0805 | R101, R207, R212, R217, R222 |
| 5 | 16A SPST | ignition:Relay_RT314 | K201, K202, K203, K204, K205 |
| 5 | 1k | Resistors_SMD:R_0805 | R203, R206, R211, R216, R221 |
| 5 | D | ignition:SOD-123F | D202, D204, D208, D212, D216 |
| 5 | MBR2H200SFT1G | ignition:SOD-123FL | D201, D205, D209, D213, D217 |
| 4 | VAL** | common:M3_MOUNT_FANCY | M3_MOUNT, M3_MOUNT, M3_MOUNT, M3_MOUNT |
| 3 | R | Resistors_SMD:R_0805 | R107, R108, R109 |
| 2 | 15p | Capacitors_SMD:C_0805 | C111, C112 |
| 2 | 430 | Resistors_SMD:R_0805 | R205, R215 |
| 2 | 4u7 | Capacitors_SMD:C_0805 | C103, C106 |
| 1 | 100R | Resistors_SMD:R_0805 | R104 |
| 1 | 100u | Capacitors_SMD:C_1206 | C108 |
| 1 | 10n | Capacitors_SMD:C_0805 | C107 |
| 1 | 1u | Capacitors_SMD:C_0805 | C110 |
| 1 | 3k3 | Resistors_SMD:R_0805 | R102 |
| 1 | 3v3 | common:TESTPOINT | TP104 |
| 1 | 510 | Resistors_SMD:R_0805 | R219 |
| 1 | 510R | Resistors_SMD:R_0805 | R209 |
| 1 | 6.3x32 | ignition:6x32_fuseclip | F101 |
| 1 | 75R | Resistors_SMD:R_0805 | R103 |
| 1 | 8MHz | common:XTAL50x32 | Y101 |
| 1 | ARM_LED | ignition:JST-PA-2-VERT | P107 |
| 1 | BATT | common:TESTPOINT | TP101 |
| 1 | BATT | ignition:PCB_SPADE | P105 |
| 1 | BUZZ | ignition:JST-PA-2-VERT | P109 |
| 1 | CH1 | ignition:PCB_SPADE | P206 |
| 1 | CH1_LED | ignition:JST-PA-2-VERT | P204 |
| 1 | CH2 | ignition:PCB_SPADE | P212 |
| 1 | CH2_LED | ignition:JST-PA-2-VERT | P210 |
| 1 | CH3 | ignition:PCB_SPADE | P203 |
| 1 | CH3_LED | ignition:JST-PA-2-VERT | P201 |
| 1 | CH4 | ignition:PCB_SPADE | P209 |
| 1 | CH4_LED | ignition:JST-PA-2-VERT | P207 |
| 1 | ContCH1 | common:TESTPOINT | TP205 |
| 1 | ContCH2 | common:TESTPOINT | TP207 |
| 1 | ContCH3 | common:TESTPOINT | TP204 |
| 1 | ContCH4 | common:TESTPOINT | TP206 |
| 1 | FiringDist | common:TESTPOINT | TP201 |
| 1 | GND | common:TESTPOINT | TP102 |
| 1 | GREEN | LEDs:LED-0805 | D105 |
| 1 | LOGO | common:cusf_logo_full_huge | G*** |
| 1 | LOGO | ignition:wile_e_rocket | G*** |
| 1 | LOGO | ignition:cusf_rocket_big | G*** |
| 1 | RED | LEDs:LED-0805 | D104 |
| 1 | RFM95W | common:RFM95W | U105 |
| 1 | RelaySense | common:TESTPOINT | TP203 |
| 1 | SMA | ignition:SMA_upright | P111 |
| 1 | STM32F071CBT6 | common:LQFP48_ST | U106 |
| 1 | SWD | common:FTSH-105-01-F-D-K | U103 |
| 1 | TSR 0.5-2433 | ignition:TSR-0_5 | U107 |
| 1 | USRelay | common:TESTPOINT | TP202 |
| 1 | YELLOW | LEDs:LED-0805 | D106 |
| 1 | nRST | common:TESTPOINT | TP103 |
The 111 most common of 112 parts.
Questions
How big is the Ignition PCB?
It measures 167.9 × 105.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ignition use?
112 parts, built around the STM32F071CBT6, RFM95W, BSS138BK and MBR2H200SFT1G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ignition KiCad files?
From the cuspaceflight/OkGo repository on GitHub, at the commit this page was made from: the board is OkGo 2/ignition/ignition.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ignition design in my own project?
Its repository states no licence, so its author keeps all rights: ask cuspaceflight before reusing the design.
More from cuspaceflight/OkGo
4- 2 layers90.5 × 51 mm
- 2 layers
- 2 layers40 × 25 mm
Okgo2usbcontrol
cuspaceflight/OkGo
Rocket motor ignition and valve control from far, far away
22 parts3
Similar boards
- 2 layers101.1 × 70.8 mm
ProjektElektronikaV6
Nom27/Projekt-elektronika
Projekt elektroniczny (schemat + PCB) inteligentnego termostatu opartego na mikrokontrolerze STM32, z łącznością WiFi (moduł ESP-12E), pomiarem temperatury czujnikiem LM335AZ, sygnalizacją dźwiękową (buzzer) oraz…
42 parts - 2 layers100 × 99.8 mm
- 2 layers100 × 100 mm
- 6 layers268 × 230 mm
Rf board
PE1RGU/hf-antenna-switch
Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.
357 parts2CERN-OHL-S-2.0 - 6 layers101.8 × 80.5 mm
- 4 layers78 × 56 mm
- 4 layers
EMG8 Wireless
im-deltax/EMG-Human-Machine-Interface
Eight-channel EMG PCB research design for assistive human-computer interaction. PCB sources only; hardware and user validation pending.
159 parts - 4 layers40.6 × 49.3 mm
Ledkiv4
JamPsym/letki
A new schematic simplification is in progress. See the next-iteration note for the checked 33 Ω candidate. This directory and its frozen exports still represent the previous 34 Ω circuit; the candidate has no…
125 parts