2 layers167.9 × 105.9 mm
2 layers90.5 × 51 mm
Control r1
cuspaceflight/OkGo3Rocket motor ignition and valve control from far, far away
- Size
- 90.5 × 51 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 66
- Nets
- 58
- Pads
- 264
- Tracks, vias
- 674, 53
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 25 Nov 2012
- Updated
- 31 Aug 2017
Overview
Control r1 is an open-source printed circuit board by cuspaceflight, from the cuspaceflight/OkGo repository on GitHub. It is a 2-layer board of 90.5 × 51 mm with 66 parts on 58 nets, routed with 674 tracks and 53 vias.
It is built around the STM32F071CBT6, MEJ2S0305SC and RFM95W, with the BSS138BK among its other parts. Its parts include 21 resistors, 14 capacitors, 10 connectors, 6 ICs and 5 diodes. It belongs with the STM32 boards of this library.
Main components
4
STM32F071CBT6
LQFP-48(7x7)-40℃~+85℃ 1.65V~3.6V 128KB 12bit 12bit 16KB 32 Bit 37 48MHz ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)MEJ2S0305SC
-- Isolated Power Modules ROHSMurataIsolated Power ModulesRFM95W
SMD-16PUncategorisedHopeRF Micro-electronics
BSS138BK
SOT-23-55℃~+150℃ 1 N-channel 1.6V 1.6Ω@10V 350mW 360mA 56pF 60V 700pC@4.5V N-Channel SOT-23 MOSFETs ROHSNexperiaMOSFETs
README
README.mdOkGo
OkGo is Cambridge University Space Flight's rocket firing controller.
OkGo was designed for testing the Quasar hybrid rocket motor. It allowed remote (over 100m of wire) control of the nitrous oxide valve and firing of the ignition e-match. It was constructed using an ad-hoc point-to-point layout. An entirely passive design, it simply uses mechanical switches to trigger relays. It was later upgraded to control two valves, one of which passed a low flow of nitrous oxide to help start the motor.
OkGo 2 was a full redesign for the launch of Martlet 2. Due to the increased safety radius (on the order of 500m) radio control is to be used. It will have 4 general purpose (valve or e-match) channels with independent continuity checking and firing, and separate firing boxes containing current limiting resistors.
OkGo 3 is another full redesign for the launch of Martlet 3. It will continuity check and ignite a single channel with a constant-current drive. Ignition and control will be small and light for portability.
Parts
66| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 10k | Resistors_SMD:R_0805 | R101, R107, R108, R109, R110, R205, R206, R211, R212 |
| 5 | 100n | Capacitors_SMD:C_0805 | C101, C102, C104, C108, C112 |
| 5 | TVS_small | Resistors_SMD:R_0603 | D101, D103, D104, D105, D106 |
| 4 | 100k | Resistors_SMD:R_0805 | R203, R204, R209, R210 |
| 4 | 180R | Resistors_SMD:R_0805 | R201, R202, R207, R208 |
| 4 | BSS138BK | Housings_SOT-23_SOT-143_TSOT-6:SOT-23 | Q201, Q202, Q203, Q204 |
| 2 | 15p | Capacitors_SMD:C_0805 | C109, C110 |
| 2 | 2u2 | Capacitors_SMD:C_0805 | C113, C114 |
| 2 | 4u7 | Capacitors_SMD:C_0805 | C103, C105 |
| 1 | 100R | Resistors_SMD:R_0805 | R102 |
| 1 | 100u | Capacitors_SMD:C_1206 | C111 |
| 1 | 10k | Capacitors_SMD:C_0805 | R106 |
| 1 | 10n | Capacitors_SMD:C_0805 | C106 |
| 1 | 1u | Capacitors_SMD:C_0805 | C107 |
| 1 | 20k LIN | control:bourns3386G | RV101 |
| 1 | 3k3 | Resistors_SMD:R_0805 | R105 |
| 1 | 3v3 | common:TESTPOINT | TP102 |
| 1 | 75R | Resistors_SMD:R_0805 | R103 |
| 1 | 8MHz | common:XTAL50x32 | Y101 |
| 1 | ADP3335 | Housings_SSOP:MSOP-8_3x3mm_Pitch0.65mm | U107 |
| 1 | ARM_LED | common:JST-PA-2 | P106 |
| 1 | BATT | common:JST-PA-2 | P105 |
| 1 | CH1 | common:JST-PA-4 | P201 |
| 1 | CH2 | common:JST-PA-4 | P202 |
| 1 | CH3 | common:JST-PA-4 | P205 |
| 1 | CH4 | common:JST-PA-4 | P206 |
| 1 | KEYSW | common:JST-PA-2 | P102 |
| 1 | LCD_HD44780 | control:LCD_MC42004A6W | U106 |
| 1 | MEJ2S0305SC | control:MEJ2S0305SC | U103 |
| 1 | POWER_SW | common:JST-PA-2 | P110 |
| 1 | PTC | Resistors_SMD:R_0805 | F101 |
| 1 | RFM95W | common:RFM95W | U105 |
| 1 | SERIAL | common:JST-PA-4 | P111 |
| 1 | SMA | common:SMA-142-0701-801 | P108 |
| 1 | STM32F071CBT6 | Housings_QFP:LQFP-48_7x7mm_Pitch0.5mm | U102 |
| 1 | SWD | common:FTSH-105-01-F-D-K | U101 |
| 1 | nRST | common:TESTPOINT | TP101 |
The 65 most common of 66 parts.
More from cuspaceflight/OkGo
4- 2 layers92.2 × 64.5 mm
- 2 layers
- 2 layers40 × 25 mm
Okgo2usbcontrol
cuspaceflight/OkGo
Rocket motor ignition and valve control from far, far away
22 parts3
Similar boards
- 2 layers101.1 × 70.8 mm
ProjektElektronikaV6
Nom27/Projekt-elektronika
Projekt elektroniczny (schemat + PCB) inteligentnego termostatu opartego na mikrokontrolerze STM32, z łącznością WiFi (moduł ESP-12E), pomiarem temperatury czujnikiem LM335AZ, sygnalizacją dźwiękową (buzzer) oraz…
42 parts - 6 layers268 × 230 mm
Rf board
PE1RGU/hf-antenna-switch
Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.
357 parts2CERN-OHL-S-2.0 - 6 layers101.8 × 80.5 mm
- 4 layers78 × 56 mm
- 4 layers
EMG8 Wireless
im-deltax/EMG-Human-Machine-Interface
Eight-channel EMG PCB research design for assistive human-computer interaction. PCB sources only; hardware and user validation pending.
159 parts - 4 layers40.6 × 49.3 mm
Ledkiv4
JamPsym/letki
A new schematic simplification is in progress. See the next-iteration note for the checked 33 Ω candidate. This directory and its frozen exports still represent the previous 34 Ω circuit; the candidate has no…
125 parts - 2 layers23.9 × 26 mm
- 2 layers116 × 40 mm
Questions
How big is the Control r1 PCB?
It measures 90.5 × 51 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Control r1 use?
66 parts, built around the STM32F071CBT6, MEJ2S0305SC, RFM95W and BSS138BK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Control r1 KiCad files?
From the cuspaceflight/OkGo repository on GitHub, at the commit this page was made from: the board is OkGo 2/control/control-r1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Control r1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask cuspaceflight before reusing the design.