2 layers95.3 × 74.9 mm
27(C)256 programmer
CNCNoob/Universal-EEPROM-programmer
Great Arduino based ROM Programmer design.
2 parts1MIT
2 layers82.6 × 61 mm
EEPROM Programmer
CNCNoob/Universal-EEPROM-programmer1Great Arduino based ROM Programmer design.
- Size
- 82.6 × 61 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 5
- Nets
- 49
- Pads
- 101
- Tracks, vias
- 308, 22
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 23 Jun 2019
- Updated
- 29 Jun 2019
Overview
EEPROM Programmer is an open-source printed circuit board by CNCNoob, from the CNCNoob/Universal-EEPROM-programmer repository on GitHub, published under the MIT licence. It is a 2-layer board of 82.6 × 61 mm with 5 parts on 49 nets, routed with 308 tracks and 22 vias.
It is built around the ARDUINO UNO R3 and 74HC595. Its parts include 3 ICs and 2 connectors. It belongs with the interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2README
README.mdUniversal-EEPROM-Programmer
Marvellouse EEPROM programming device that will support many EEPROMs and some EPROMs
main Arduino shield with 28pin molex connector which connects to user specific boards.
Created and programmed using: KiCad, Aduino and processing
Parts
5| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 74HC595 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U2, U3 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3 | U1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_02x17_Odd_Even | Connector_IDC:IDC-Header_2x17_P2.54mm_Vertical | J1 |
Questions
How big is the EEPROM Programmer PCB?
It measures 82.6 × 61 mm and has 2 copper layers, 1.6 mm thick.
What parts does the EEPROM Programmer use?
5 parts, built around the ARDUINO UNO R3 and 74HC595. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EEPROM Programmer KiCad files?
From the CNCNoob/Universal-EEPROM-programmer repository on GitHub, at the commit this page was made from: the board is Main Arduino version/Main Arduino shield/EEPROM_Programmer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the EEPROM Programmer design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from CNCNoob/Universal-EEPROM-programmer
1Similar boards
- 2 layers170.2 × 119.4 mm
Sentinel
YousefAliAicha/sentinel-arduino-firmware
Adaptive traffic-light FSM on the Arduino UNO R3 — pedestrian preemption, LDR-gated night mode with HC-SR04 vehicle detection, and a multiplexed 7-segment countdown. Fully non-blocking.
25 parts2MIT - 2 layers89 × 103.5 mm
Controller
ayushmanyadav2006/Flight-Controller-
Created a electronic control hardware to control the roll, pitch, yaw of a airplane Also the speed of the airplane, landing gears etc
24 parts - 2 layers
RGB LED CUBE 8X8X8
kirtan885/RGB-CUBE-8X8X8
Arduino 74HC595 8-LED Driver Block — A modular LED driver prototype using an Arduino Uno, 74HC595 shift register, and 8 NPN transistor low-side switches.
258 partsMIT - 2 layers50 × 45 mm
Speedometer
TheGregggg/arduino-speedometer
DIY Sim racing Speedometer using Arduino, servo motors and eight-segment display
14 parts - 2 layers69 × 57.5 mm
- 2 layers68.8 × 53.6 mm
Relatively Universal ROM Programmer
AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.
149 parts257GPL-3.0 - 2 layers69.1 × 53.8 mm
Motor controller
AlanFord/self-balancing-stick
Dual Axis Reaction Wheel Inverted Pendulum
25 parts79MIT - 2 layers68.6 × 53.3 mm
Protogasm Board V2
Edging-Machines/Edging-Machines
This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.
14 parts67MIT