

ESP32Hardware
Chat64 for Commodore64
- Size
- 99.7 × 58.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 21
- Nets
- 87
- Pads
- 208
- Tracks, vias
- 701, 62
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 5 Sep 2026
- Updated
- 21 Oct 2026
Overview
ESP32Hardware is an open-source printed circuit board by bvenneker, from the bvenneker/CHAT64 repository on GitHub. It is a 2-layer board of 99.7 × 58.4 mm with 21 parts on 87 nets, routed with 701 tracks and 62 vias.
It is built around the 74HCT125PW, 74HC00D and 74HC597D, with the BC548 and BAT86 among its other parts. Its parts include 6 ICs, 4 capacitors, 3 resistors, 2 diodes and 2 transistors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
574HCT125PW
TSSOP-14-40℃~+125℃ 1 15ns@4.5V,50pF 160uA 4 4.5V~5.5V 6mA 6mA 74HCT Tri-State Unidirectional TSSOP-14 Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffers, Drivers, Receivers, Transceivers74HC00D
SOP-14-40℃~+125℃ 1.5V、3.15V、4.2V 1.9V、3.7V、5.9V 100mV、400mV、400mV 2 2V~6V 4 40uA 5.2mA 5.2mA 500mV~1.8V 74HC Series 7ns@6V,50pF NAND Gate SOIC-14 Logic Gates ROHSNexperiaLogic Gates74HC597D
SOP-16L-40℃~+125℃ 1 15ns@6V,50pF 2.8V~6V 28MHz 74HC SOP-16L Shift Registers ROHSMDDShift RegistersBC548
TO-92TO-92 Bipolar (BJT) ROHSDDFBipolar (BJT)BAT86
DO-341 Independent 200mA 50V 5A 5uA@40V 900mV@100mA DO-34 Schottky Diodes ROHSNexperiaSchottky Diodes
README
README.mdCHAT64_C64
Chat64 for Commodore64, Sinclair ZX Spectrum, Atari 800XL, MSX and Amstrad CPC.
Parts
21| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C1, C2, C3, C4 |
| 2 | 270Ω | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R3 |
| 2 | BC548 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2 |
| 1 | 100Ω | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5 |
| 1 | 28C64 | Barts:28ZIF600_2 | U4 |
| 1 | 74HC00 | Package_DIP:DIP-14_W7.62mm_LongPads | U1 |
| 1 | 74HC597 | Package_DIP:DIP-16_W7.62mm_LongPads | U2 |
| 1 | 74HCT125 | Package_DIP:DIP-14_W7.62mm_LongPads | U6 |
| 1 | 74LS244 | Package_DIP:DIP-20_W7.62mm_LongPads | U3 |
| 1 | BAT86 | Diode_THT:D_DO-34_SOD68_P7.62mm_Horizontal | D1 |
| 1 | C64-Exp-Port | KicadFootprints:C64-Cart-NoSilkS | X1 |
| 1 | Jumper | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | LED | LED_THT:LED_D3.0mm | D2 |
| 1 | Logo_Open_Hardware_Small | Symbol:OSHW-Logo2_14.6x12mm_SilkScreen | LOGO1 |
| 1 | Reset | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | mini_esp32 | KicadFootprints:ESP32_mini | U5 |
More from bvenneker/CHAT64
3- 4 layers87 × 65.7 mm

- 4 layers99.5 × 79.2 mm

- 4 layers63.9 × 82.6 mm

Similar boards
- 2 layers113.5 × 134.6 mm

Kim-1-RAM ROM
eduardocasino/kim-1-mtu-ram-rom
KIM-1 RAM/ROM Expansion Board for the MTU Backplane
41 parts3 - 2 layers99.5 × 99.5 mm

Balancer
kwiecinski/BMS-and-offgrid-photovoltaic-management-system
Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.
173 parts3MIT - 2 layers247.8 × 124.2 mm

- 4 layers81.7 × 61 mm

Pmod interface board
alpyen/zynq-gbcartreader
Embedded Software Development project to read & write GameBoy cartridges.
31 parts3 - 4 layers101.6 × 147.3 mm

- 2 layers144 × 100 mm

- 2 layers

- 4 layers100 × 100 mm

Questions
How big is the ESP32Hardware PCB?
It measures 99.7 × 58.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32Hardware use?
21 parts, built around the 74HCT125PW, 74HC00D, 74HC597D and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32Hardware KiCad files?
From the bvenneker/CHAT64 repository on GitHub, at the commit this page was made from: the board is Commodore/KiCAD/Dev cartridge/Chat_2024_rev_3.9_DEV/ESP32Hardware.kicad_pcb and its schematic AmstradCPC/KiCAD/cpc_Chat64_v1.1/cpc_Chat64_v1.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32Hardware design in my own project?
Its repository states no licence, so its author keeps all rights: ask bvenneker before reusing the design.