
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

Simple PCB for a multi-room audio board
Djflab pcb is an open-source printed circuit board by buergi, from the buergi/djflab-board repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 60 × 75 mm with 29 parts on 19 nets, routed with 136 tracks and 0 vias.
It is built around the WS2812B. Its parts include 10 diodes, 7 resistors, 3 connectors and 1 switch. It belongs with the audio and music boards of this library.
The DJ FLAB is a multi-room audio control board from Fablab München.
Multiple of these boards are connected to an ESP32, each providing a simple control interface for a single room. It has a rotary encoder for controlling the volume and switching the audio source, as well as ten WS2812B LEDs for indication.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10 |
| 6 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R5, R6, R7 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 2 | Conn_01x03_Pin | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J2, J3 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_2.5mm_Pad_Via | H5, H6 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 1 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | Conn_01x06_Pin | Connector_JST:JST_XH_S6B-XH-A_1x06_P2.50mm_Horizontal | J1 |
| 1 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Bourns_Vertical_PEC12R-3x17F-Sxxxx | SW1 |

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

FrameworkComputer/ExpansionCards
Reference designs and documentation to create Expansion Cards for the Framework Laptop



PrintersForAnts/Micron
If you want to purchase full kits there are 3 available (Kits are slowly updating to R1 hardware just make sure to double check the included hardware in your kit and if you have any questions reach out in the discord)



It measures 60 × 75 mm and has 2 copper layers, 1.6 mm thick.
29 parts, built around the WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the buergi/djflab-board repository on GitHub, at the commit this page was made from: the board is djflab-pcb/djflab-pcb.kicad_pcb and its schematic djflab-pcb/djflab-pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).