

CanSat
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 113
- Nets
- 99
- Pads
- 446
- Tracks, vias
- 917, 110
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 11 Nov 2025
- Updated
- 9 Oct 2026
Overview
CanSat is an open-source printed circuit board by budabalint, from the budabalint/T.E.E.M.O repository on GitHub. It is a 4-layer board with 113 parts on 99 nets, routed with 917 tracks and 110 vias.
It is built around the ESP32-S3-WROOM-1-N8, BME280 and CH340G, with the SGP41-D-R4, TPS61088RHLT and VEML7700-TR among its other parts. Its parts include 49 capacitors, 26 resistors, 12 ICs, 8 connectors and 5 diodes. It belongs with the ESP32 boards of this library.
Main components
9ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorCH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersSGP41-D-R4
DFN-6(2.4x2.4)DFN-6(2.4x2.4) VOC Sensors ROHSSensirionVOC SensorsTPS61088RHLT
VQFN-20-EP(3.6x4.6)-40℃~+125℃@(TJ) 1 10A 1uA 2.2MHz 2.7V~12V 4.5V~12.6V Boost Boost Built-in Yes VQFN-20-EP(3.6x4.6) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersVEML7700-TR
SMD-4P-25℃~+85℃ 120klx 16bit 2.35mm 2.5V~3.6V 3mm 6.8mm I2C Light Intensity Low power/sleep mode、Spectral correction/filtering、High dynamic range measurement、Adjustable gain control、Interrupt/event trigger、Built-in temperature compensation SMD-4P Ambient Light Sensors ROHSVishay IntertechnologyAmbient Light SensorsBNO085
LGA-28(3.8x5.2)1.65V~3.6V 12bit、16bit IMU (accelerometer + gyroscope) SPI、I2C、UART X,Y,Z X,Y,Z ±2000dps ±8g LGA-28(3.8x5.2) Accelerometers ROHSCEVAAccelerometersBC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)HCM0703-3R3-R
SMD,7.1x6.6mm13.5A 28mΩ 3.3uH 6A ±20% SMD,7.1x6.6mm Power Inductors ROHSEatonPower Inductors
Parts
113| Qty | Value | Footprint | References |
|---|---|---|---|
| 23 | 4,7uf | Capacitor_SMD:C_0805_2012Metric | C11, C12, C13, C15, C17, C18, C20, C21, C22, C23, C24, C27, C28, C29, C30, C34 +7 |
| 14 | 100nf | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C7, C16, C19, C25, C26, C31, C33, C42, C43, C45 |
| 6 | 10k | Resistor_SMD:R_0805_2012Metric | R7, R8, R10, R13, R14, R97 |
| 5 | LED | Diode_SMD:D_1206_3216Metric | D1, D2, D3, D5, D6 |
| 4 | , , , | ||
| 4 | 1K | Resistor_SMD:R_0805_2012Metric | R11, R12, R93, R94 |
| 3 | 100n | Capacitor_SMD:C_0805_2012Metric | C10, C32, C40 |
| 3 | 1uf | Capacitor_SMD:C_0805_2012Metric | C5, C6, C8 |
| 3 | 33k | Resistor_SMD:R_0805_2012Metric | R4, R5, R39 |
| 2 | 0.056Ω | Resistor_SMD:R_1206_3216Metric | R1, R28 |
| 2 | 105k | Resistor_SMD:R_0805_2012Metric | R2, R37 |
| 2 | 10R | Resistor_SMD:R_0805_2012Metric | R35, R98 |
| 2 | 22pf | Capacitor_SMD:C_0805_2012Metric | C56, C57 |
| 2 | 300k | Resistor_SMD:R_0805_2012Metric | R3, R6 |
| 2 | 5.1K | Resistor_SMD:R_0805_2012Metric | R9, R26 |
| 2 | 68pf | Capacitor_SMD:C_0805_2012Metric | C37, C41 |
| 2 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | GPS | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J1, J8 |
| 2 | HCM0703-3R3-R | panel:HCM1A0805 | L1, L2 |
| 2 | INA226 | Package_SO:VSSOP-10_3x3mm_P0.5mm | U5, U14 |
| 2 | bno_scl | TestPoint:TestPoint_Pad_D1.5mm | BNO_BOOT, SCL |
| 1 | 0R | Resistor_SMD:R_0805_2012Metric | R15 |
| 1 | 1.2nF | Capacitor_SMD:C_0805_2012Metric | C9 |
| 1 | 100R | Resistor_SMD:R_0805_2012Metric | R36 |
| 1 | 10nf | Capacitor_SMD:C_0805_2012Metric | C14 |
| 1 | 12K 1% | Resistor_SMD:R_0805_2012Metric | R38 |
| 1 | 12MHz | Crystal:Crystal_SMD_HC49-SD | Y2 |
| 1 | 2.4G_Radio | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J4 |
| 1 | AP64501SP-13 | panel:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.71x3.4mm_ThermalVias_BigVias | U4 |
| 1 | ASEK-32.768KHZ-L-R-T | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | U7 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U21 |
| 1 | BNO085 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U23 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U8 |
| 1 | Conn_01x02_Socket | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Battery |
| 1 | Conn_01x06_Socket | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J7 |
| 1 | Conn_01x06_Socket | Connector_JST:JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J6 |
| 1 | Conn_01x07_Pin | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J5 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U3 |
| 1 | FLIR | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J3 |
| 1 | SGP41-D-R4 | panel:XDCR_SGP41-D-R4 | U2 |
| 1 | TPS61088RHLT | panel:BQ24031IRHLRQ1 | IC1 |
| 1 | USB_C | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | J12 |
| 1 | VEML7700-TR | panel:XDCR_VEML7700-TR | U1 |
| 1 | W5500IO | panel:W5500-io | U9 |
| 1 | bno_sda | TestPoint:TestPoint_Pad_D1.5mm | SDA |
More from budabalint/T.E.E.M.O
2- 4 layers173.2 × 52.5 mm

- 2 layers22.8 × 18.4 mm

Similar boards
- 2 layers65 × 30 mm

- 6 layers120 × 70.2 mm

CM5IO
NBence0/JedlikBots
Welcome to the official GitHub page of JedlikBots! 🎓🤖 We are the dedicated team of software development and robotics students from the Jedlik Ányos Technical School in Győr, Hungary.
250 parts - 2 layers60 × 77.7 mm

- 4 layers60 × 80 mm

Wisp
huulanka/wisp
Open-source ESP32 room climate monitor — CO2, VOC, humidity, temperature and light sensing with custom PCB, MQTT/HomeKit integration, and OTA firmware updates. Full hardware + software, from schematic to BOM.
91 partsMIT - 2 layers23.6 × 0.1 mm

- 2 layers183.2 × 65.1 mm

- 4 layers60 × 60 mm

Rocket payload
Gupatron/Gupsfirstpcb
This is the first pcb that I will manufacture and intend to use for teleop usecases in my personal projects.
138 parts - 4 layers74.4 × 64.2 mm

Iot device pcb
ODARI-CHARLES1/iot_device_pcb
Hardware design for a air conditioner pcb design using Kicad software. This is for learning purpose only not manufacturable.
76 parts2
Questions
What parts does the CanSat use?
113 parts, built around the ESP32-S3-WROOM-1-N8, BME280, CH340G and SGP41-D-R4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CanSat KiCad files?
From the budabalint/T.E.E.M.O repository on GitHub, at the commit this page was made from: the board is Circuit/CanSat/CanSat.kicad_pcb and its schematic Circuit/CanSat/2.4G-Radio.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CanSat design in my own project?
Its repository states no licence, so its author keeps all rights: ask budabalint before reusing the design.