2 layers85 × 58.5 mm
2 layers123 × 50 mm
Single sided DIY
bubbapizza/doorController1A simple arduino RFID door controller
- Size
- 123 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 23
- Pads
- 99
- Tracks, vias
- 161, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 11 Sep 2013
- Updated
- 25 Dec 2014
Overview
Single sided DIY is an open-source printed circuit board by bubbapizza, from the bubbapizza/doorController repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 123 × 50 mm with 30 parts on 23 nets, routed with 161 tracks and 0 vias.
It is built around the RJ45. Its parts include 10 resistors, 6 diodes, 5 connectors, 2 ICs and 2 transistors. It belongs with the radio and wireless boards of this library.
Main components
1README
READMEThis is (going to be) a full DIY solution for a door controller. The door can be locked or unlocked using an arduino or a raspberry pi to interface witha Parallax serial RFID card reader for the controller hardware.
The backend logic for the door controller is handled in python.
The arduino sketches have no logic in them whatsoever. All they do is
accept single character commands over the virtual serial port
and control some lights, a buzzer and rfid controller. All back-end logic
is handled using python.
I've also included a couple Arduino sketches for dealing w/ Wiegand RFID card readers. I'm not sure if the wiegand stuff actually works or not since I never tested it. One sketch is an RFID emulator which is supposed to emulate a wiegand card reader. The other sketch is for controlling a door using a device that speaks the wiegand protocol. testing
Shawn Wilson Oct 29, 2013
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 1pin | , , , | |
| 3 | 330 | R5 | R4, R5, R11 |
| 3 | CONN_2 | C2_KF103 | P2, P3, P4 |
| 3 | LED | LED-5MM-RED | D2, D3, D4 |
| 2 | 10K | R5 | R1, R7 |
| 2 | 1N4007 | DO-41 | D5, D8 |
| 2 | 2N3904 | TO92-2N3904 | Q1, Q2 |
| 1 | 1.8K | R5 | R2 |
| 1 | 200 | R5 | R8 |
| 1 | 2K | R5 | R6 |
| 1 | 3.3K | R5 | R3 |
| 1 | 4N35 | DIP-6__300 | IC1 |
| 1 | 680 | R5 | R12 |
| 1 | CONN_13X2 | pin_array_13x2 | P1 |
| 1 | LED | LED-5MM | D1 |
| 1 | RELAY | RELAY_AZ942 | U1 |
| 1 | RJ45 | RJ45_8 | J1 |
| 1 | SW_PUSH | SW_PUSH_SMALL | SW1 |
More from bubbapizza/doorController
2- 2 layers62 × 15 mm
Similar boards
- 2 layers33.7 × 97.8 mm
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 4 layers84 × 82 mm
Toad
travisgoodspeed/goodfet
An embedded bus adapter for various microcontrollers and radios.
241 parts333 - 2 layers100 × 100 mm
- 2 layers50 × 55.4 mm
- 2 layers67.9 × 47.8 mm
Platine
nv1t/standing-desk-interceptor
I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project
11 parts52CC0-1.0 - 4 layers90 × 75 mm
- 4 layers73.9 × 84.5 mm
Aei
Severson-Group/AMDC-Hardware
Circuit board designs for controlling advanced motor systems
54 parts51 - 2 layers99 × 60 mm
Pwr
mfkiwl/KiwiSDR_PCB
KiCAD PCB files for KiwiSDR project including active antenna and bias tee
64 parts46
Questions
How big is the Single sided DIY PCB?
It measures 123 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Single sided DIY use?
30 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Single sided DIY KiCad files?
From the bubbapizza/doorController repository on GitHub, at the commit this page was made from: the board is KiCAD/rpi-door-control/single-sided-DIY.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Single sided DIY design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).