

Nylok Heater
Two-mode handheld induction-heater controller with KiCad design files, product design rendering, engineering calculations, and full cost analysis.
- Size
- 38 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 68
- Nets
- 20
- Pads
- 167
- Tracks, vias
- 20, 0
- Routed
- Yes
- KiCad
- KiCad 8 (file 20240108)
- Created
- 3 Oct 2026
- Updated
- 2 Nov 2026
Overview
Nylok Heater is an open-source printed circuit board by boydportfolio, from the boydportfolio/Nylok-Heater repository on GitHub. It is a 2-layer board of 38 × 100 mm with 68 parts on 20 nets, routed with 20 tracks and 0 vias.
It is built around the STM32G030F6P6, MP8771GQ-Z and AP7381-33Y, with the M2.5, AO4409 and BC817-40 among its other parts. Its parts include 25 resistors, 23 capacitors, 5 ICs, 4 connectors and 3 transistors. It belongs with the STM32 boards of this library.
Main components
6STM32G030F6P6
TSSOP-20-40℃~+85℃ 12bit 17 2V~3.6V 32 Bit 32KB 64MHz 8KB ARM Cortex-M0+ Built-in+External FLASH TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)MP8771GQ-Z
QFN-16(3x3)-40℃~+125℃@(TJ) 1 100uA 10A 3V~18V 600mV~12V 700kHz Adjustable Buck Buck Built-in Yes QFN-16(3x3) DC-DC Converters ROHSMonolithic Power SystemsDC-DC ConvertersAP7381-33Y
SOT-89-40℃~+125℃@(Tj) 1 150mA 1V@(100mA) 2.5uA 3.3V 40V 60dB Fixed Positive Short Circuit Protection、Thermal Shutdown SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsM2.5
-0.45mm 2.5mm 2mm 5mm DIN934 Hex M2.5X0.45 Nickel plated Silver white - Hexagonal nutsShuntianHex NutAO4409
SOP-8-55℃~+150℃ 1 P-Channel 1.9V 100nC@10V 15A 30V 3W 5.27nF 6.2mΩ@10V、9.5mΩ@4.5V 745pF 945pF P-Channel SOP-8 MOSFETs ROHSUMWMOSFETsBC817-40
SOT-23-65℃~+150℃ 1 NPN 100MHz 100nA 250 345mW 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSNexperiaBipolar (BJT)
README
README.mdNylok Handheld Induction Heater Controller
A two-mode handheld induction-heater controller designed in KiCad for the Notre Dame / Marmon / Nylok Innovate-a-thon.
Heater product design
The rendering shows the heater product design. The KiCad files below describe its controller board; heating also requires a separate induction driver and work coil.
Interested in the CAD files and final product designs? Please contact Noah Boyd.
Full cost analysis
Full cost analysis covers parts, heating calculations, battery runtime, and manufacturing estimates for 5,000 units. The original Word document and Google Drive source are also available.
| Cost scenario | Basic heater | Two-mode heater with countdown |
|---|---|---|
| Prototype parts allocation | $18.06 | $31.37 |
| Estimated manufacturing cost per heater at 5,000 units | $13.14 | $19.14 |
Source prices were checked October 3, 2026. Prototype figures exclude the housing, tools, shipping, and tax; production figures include estimated housing, assembly, functional test, packaging, and reserve. See the full analysis for all assumptions and exclusions.
Controller PCB

[!CAUTION] Do not fabricate or energize this board without a qualified electrical and safety review. See the review checklist.
Overview
The controller uses two protected 18650 cells in series to power a controller board that:
- measures input current;
- provides regulated 5 V and 3.3 V rails;
- controls a switched DC output for an external zero-voltage-switching (ZVS) induction driver;
- exposes an Inter-Integrated Circuit (I2C) display connector; and
- provides a Serial Wire Debug (SWD) programming header for the STM32 controller.
The controller switches power to the external ZVS driver, which drives the work coil. Connect the coil to that driver, not directly to connector J2 or the battery.
Repository contents
.
├── hardware/ KiCad project, schematic, PCB, bill of materials (BOM), and logical net map
├── COST_ANALYSIS.md Full readable cost analysis and calculations
├── Nylok_Heater_Cost_Analysis.docx Original complete cost-analysis document
├── docs/ Engineering study and connection diagram
├── fab/ Fabrication and electrical-review notes
├── renders/ Heater product design and board views
└── scripts/ Repository package checksKey files:
COST_ANALYSIS.md: full cost breakdown, calculations, production estimates, and referencesNylok_Heater_Cost_Analysis.docx: original analysis documentrenders/Nylok_Heater_Product_Design.png: actual heater product design renderinghardware/Nylok_Heater.kicad_pro: KiCad projecthardware/Nylok_Heater.sch: legacy KiCad schematichardware/Nylok_Heater.kicad_pcb: nominal 38 mm × 100 mm, two-layer PCBhardware/BOM.csv: component/value listhardware/NETS.csv: logical net mapdocs/Nylok_Labeled_PCB_and_Connections.png: labeled placement and connection diagramdocs/Induction_System_Specification.md: research, assumptions, calculations, and primary sources
Open the project
-
Install KiCad 10 or later.
-
Clone the repository:
bash git clone https://github.com/3nboyd/Nylok-Heater.git cd Nylok-Heater -
Open
hardware/Nylok_Heater.kicad_pro. -
Allow KiCad to convert the legacy
.schfile if prompted, but review the resulting diff before committing it. -
Read
docs/Induction_System_Specification.mdbefore using the design data.
To check the repository package itself:
python3 scripts/validate_repo.pyThis script checks file presence, project metadata, BOM/net structure, PCB references, and PNG integrity. It does not certify electrical correctness, safety, or fabrication readiness.
Safety
Induction heating combines high current, resonant switching, strong local heating, rechargeable cells, and potentially hazardous workpiece temperatures. A short circuit, unsuitable component, control fault, inadequate insulation, or incorrect battery protection can cause burns, fire, cell venting, or equipment damage.
A qualified engineer must review the power stage, protection, thermal behavior, creepage/clearance, component ratings, coil/tank behavior, enclosure, battery system, and failure modes before fabrication or use. Early development requires current-limited isolated laboratory power, appropriate PPE, guarding, instrumentation, and fire precautions.
Contributing
Improvements are welcome. Please read CONTRIBUTING.md before opening an issue or pull request. Changes to fabrication status must include engineering-review and test evidence.
License
No open-source license has been selected. The repository is public for review and collaboration, but publication alone does not grant permission to copy, modify, manufacture, or redistribute the design. The owner can add an OSI/OSHWA-compatible license later after choosing the intended terms.
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | M2.5 | MountingHole_2.5mm | H1, H2, H3, H4 |
| 1 | 1.5uH | Nylok:L1 | L1 |
| 1 | 10 | Nylok:R2 | R2 |
| 1 | 10 | Nylok:R3 | R3 |
| 1 | 100 | Nylok:R14 | R14 |
| 1 | 100k | Nylok:R21 | R21 |
| 1 | 100k | Nylok:R17 | R17 |
| 1 | 100k | Nylok:R7 | R7 |
| 1 | 100k | Nylok:R5 | R5 |
| 1 | 100k | Nylok:R18 | R18 |
| 1 | 100n | Nylok:C8 | C8 |
| 1 | 100n | Nylok:C10 | C10 |
| 1 | 100n | Nylok:C20 | C20 |
| 1 | 100n | Nylok:C3 | C3 |
| 1 | 100n | Nylok:C23 | C23 |
| 1 | 100n | Nylok:C2 | C2 |
| 1 | 100n | Nylok:C22 | C22 |
| 1 | 10k | Nylok:R25 | R25 |
| 1 | 10k | Nylok:R24 | R24 |
| 1 | 10k | Nylok:R8 | R8 |
| 1 | 10k | Nylok:R20 | R20 |
| 1 | 10n | Nylok:C16 | C16 |
| 1 | 10n | Nylok:C4 | C4 |
| 1 | 10n | Nylok:C1 | C1 |
| 1 | 10u | Nylok:C19 | C19 |
| 1 | 1k | Nylok:R26 | R26 |
| 1 | 1k | Nylok:R4 | R4 |
| 1 | 1k | Nylok:R11 | R11 |
| 1 | 1u | Nylok:C9 | C9 |
| 1 | 1u 16V | Nylok:C17 | C17 |
| 1 | 2.2u | Nylok:C18 | C18 |
| 1 | 2.49k 1% | Nylok:R10 | R10 |
| 1 | 22u 25V X7R | Nylok:C5 | C5 |
| 1 | 22u 25V X7R | Nylok:C7 | C7 |
| 1 | 22u 25V X7R | Nylok:C6 | C6 |
| 1 | 23.2k 1% | Nylok:R9 | R9 |
| 1 | 33k | Nylok:R6 | R6 |
| 1 | 4.7k | Nylok:R23 | R23 |
| 1 | 4.7k | Nylok:R22 | R22 |
| 1 | 4.7k | Nylok:R13 | R13 |
| 1 | 4.7k | Nylok:R16 | R16 |
| 1 | 4.7u | Nylok:C21 | C21 |
| 1 | 47k | Nylok:R15 | R15 |
| 1 | 47k | Nylok:R19 | R19 |
| 1 | 47n | Nylok:C11 | C11 |
| 1 | 47u 10V X7R | Nylok:C14 | C14 |
| 1 | 47u 10V X7R | Nylok:C13 | C13 |
| 1 | 47u 10V X7R | Nylok:C12 | C12 |
| 1 | 54.9k 1% | Nylok:R12 | R12 |
| 1 | 56p C0G | Nylok:C15 | C15 |
| 1 | AO4409 | Nylok:Q1 | Q1 |
| 1 | AO4409 | Nylok:Q2 | Q2 |
| 1 | AP7381-33 | Nylok:U3 | U3 |
| 1 | BATTERY IN | Nylok:J1 | J1 |
| 1 | BC817-40 | Nylok:Q3 | Q3 |
| 1 | HEATER OUT | Nylok:J2 | J2 |
| 1 | I2C DISPLAY | Nylok:J4 | J4 |
| 1 | INA180A2 | Nylok:U1 | U1 |
| 1 | MCP4725 | Nylok:U5 | U5 |
| 1 | MODE | Nylok:SW2 | SW2 |
| 1 | MP8771 | Nylok:U2 | U2 |
| 1 | START/STOP | Nylok:SW1 | SW1 |
| 1 | STATUS | Nylok:D1 | D1 |
| 1 | STM32G030F6P6 | Nylok:U4 | U4 |
| 1 | SWD | Nylok:J3 | J3 |
Similar boards
- 4 layers50 × 100 mm

- 4 layers117 × 69.4 mm

KINO D4 Carrier A0 2
b5463/kino-d4
Open-source four-lens digital camera with synchronized capture, original-frame storage, and a USB control workbench.
256 parts4 - 2 layers96 × 97 mm

- 2 layers100 × 93.9 mm

OpenFanHub
koskev/OpenFanHub
This project aims to provide plug and play solution for controlling fans and reading temperatures
120 partsGPL-3.0 - 2 layers50.8 × 25.4 mm

Ckt irsense split
IowaScaledEngineering/ckt-irsense
CKT-IRSENSE Reflective Infrared Proximity Sensor
26 parts1 - 2 layers50 × 50 mm

- 2 layers50.8 × 25.4 mm

- 2 layers127 × 76.2 mm

Questions
How big is the Nylok Heater PCB?
It measures 38 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Nylok Heater use?
68 parts, built around the STM32G030F6P6, MP8771GQ-Z, AP7381-33Y and M2.5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Nylok Heater KiCad files?
From the boydportfolio/Nylok-Heater repository on GitHub, at the commit this page was made from: the board is hardware/Nylok_Heater.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Nylok Heater design in my own project?
Its repository states no licence, so its author keeps all rights: ask boydportfolio before reusing the design.