

SolderReflowPlate
RP2040-powered PCB solder reflow plate with replaceable heaters and better temperature control
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 65
- Pads
- 204
- Tracks, vias
- 296, 30
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 15 May 2023
- Updated
- 15 May 2023
Overview
SolderReflowPlate is an open-source printed circuit board by bikeNomad, from the bikeNomad/SolderReflowPlate repository on GitHub. It is a 2-layer board with 48 parts on 65 nets, routed with 296 tracks and 30 vias.
It is built around the RP2040, W25Q128JVSIQ and HT7533-1, with the SS54, FDS4141-NL-VB and HCM4912000000ABJT among its other parts. Its parts include 21 capacitors, 10 resistors, 4 ICs, 3 diodes and 3 connectors. It belongs with the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHHT7533-1
SOT-23-5-40℃~+85℃@(Ta) 1 100mA 2.5uA 25mV@(1mA) 3.3V 30V Fixed Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHOLTEKVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSS54
SMA(DO-214AC)-55℃~+125℃ 1mA@40V 40V 550mV@5A 5A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesFDS4141-NL-VB
SO-8-55℃~+150℃ 1 P-Channel 1.2V 10.2A 10mΩ@10V 291pF 3.007nF 335pF 33nC@4.5V 40V 4W P-Channel SO-8 MOSFETs ROHSVBsemi ElecMOSFETsHCM4912000000ABJT
HC-49S-SMD-10℃~+60℃ 12MHz 18pF 80Ω ±30ppm ±50ppm HC-49S-SMD Crystals ROHSCITIZENCrystalsIRLR8726TRPBF
TO-252-55℃~+175℃ 1 N-channel 1.8V 2.15nF 205pF 23nC 30V 5.8mΩ@10V 75W 86A TO-252 MOSFETs ROHSInfineon TechnologiesMOSFETs
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0402_1005Metric | C6, C7, C8, C9, C11, C13, C14, C15, C16, C17, C20 |
| 4 | 10u | Capacitor_SMD:C_0805_2012Metric | C5, C18, C19, C21 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R6, R9 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R3 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C10, C12 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 47 | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | 680uF 35V | Capacitor_SMD:CP_Elec_10x10.5 | C1, C2 |
| 2 | NetTie_2 | NetTie:NetTie-2_SMD_Pad1.3mm | NT1, NT2 |
| 2 | NetTie_2 | NetTie:NetTie-2_SMD_Pad2.0mm | NT1, NT2 |
| 2 | SS54 | Diode_SMD:D_SMA | D2, D3 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | DNF | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | FDS4141-NL-VB | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q1 |
| 1 | HCM4912000000ABJT | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | HT7533-1 | Package_TO_SOT_SMD:SOT-89-3 | U5 |
| 1 | INA219AIDR | footprints:D0008A_N | U1 |
| 1 | IRLR8726TRPBF | Package_TO_SOT_SMD:TO-252-2 | Q2 |
| 1 | R030 | Resistor_SMD:R_2010_5025Metric | R10 |
| 1 | RP2040 | RP2040_minimal:RP2040-QFN-56 | U4 |
| 1 | SS54 | Diode_SMD:D_SOD-123 | D1 |
| 1 | USB_B_Micro | RP2040_minimal:USB_Micro-B_Amphenol_10103594-0001LF_Horizontal_modified | J3 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
Similar boards
- 4 layers65 × 75 mm

- 2 layers100 × 100 mm

Heatplate v1.1
DerSpatz/PCB-reflow-solder-heat-plate
hardware design for a PCB reflow solder heat plate
57 parts179MIT - 2 layers82 × 52 mm

EmoePower V1.0
emoestudio/EmoePower
A DIY Buck-Boost Power Supply for Laboratory works and personal use, based on LM5175 and ESP32.
72 parts20GPL-3.0 - 2 layers100 × 100 mm

Relow solder hot plate
ldab/reflow-solder-hot-plate
USB-C powered, esp32s3 based, hot plate
52 parts1WTFPL - 2 layers99.9 × 79.3 mm

Led controller
azaslavskis/WLED-Controller
Simple project that takes care of LED strips and connect them using esp32 to home assistant interface
65 partsMIT - 2 layers100 × 112.5 mm

- 4 layers152.4 × 63.5 mm

- 2 layers163.7 × 124.3 mm

Questions
What parts does the SolderReflowPlate use?
48 parts, built around the RP2040, W25Q128JVSIQ, HT7533-1 and SS54. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SolderReflowPlate KiCad files?
From the bikeNomad/SolderReflowPlate repository on GitHub, at the commit this page was made from: the board is SolderReflowPlate.kicad_pcb and its schematic SolderReflowPlate.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SolderReflowPlate design in my own project?
Its repository states no licence, so its author keeps all rights: ask bikeNomad before reusing the design.