

At high
Homebrew discrete logic CPU
- Size
- 100 × 100 mm
- Copper layers
- 4
- Thickness
- 1.59 mm
- Parts
- 33
- Nets
- 304
- Pads
- 870
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Feb 2023
- Updated
- 28 Dec 2025
Overview
At high is an open-source printed circuit board by bcrist, from the bcrist/vera repository on GitHub, published under the MIT licence. It is a 4-layer board of 100 × 100 mm with 33 parts on 304 nets.
It is built around the AP62300TWU, 74LVC574AD and MMST3904, with the NRS5040T3R3NMGJ among its other parts. Its parts include 16 capacitors, 8 ICs, 5 resistors, 2 connectors and 1 transistor.
Main components
4AP62300TWU
TSOT-26-40℃~+125℃ 1 155uA 3A 4.2V~18V 750kHz 763mV~7V Adjustable Buck Buck Built-in Yes TSOT-26 DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters74LVC574AD
SO-20-300mil-40℃~+125℃ 1 1.5ns 1.65V~3.6V 150MHz 24mA 24mA 2ns 3.5ns@3.3V,50pF 40uA 5pF 74LVC Series 8 D-Type Enable Rising Edge Tri-State SOIC-20-300mil Flip Flops ROHSNexperiaFlip FlopsMMST3904
SOT-323Bipolar (BJT)hongjiachengNRS5040T3R3NMGJ
SMD,4.9x4.9mm27mΩ 3.3A 3.3uH 4A ±30% SMD,4.9x4.9mm Power Inductors ROHSTaiyo YudenPower Inductors
README
readme.mdHomebrew discrete-logic CPU
"I call it Vera" - Jayne Cobb
Specs
- up to 20 MHz clock
- 4-stage pipeline (runs 4 threads simultaneously)
- 32x 32b general purpose registers (stack addressed)
- 32b ALU (2x L4C381)
- 32b logarithmic shifter
- 16b * 16b -> 32b single cycle multiplier (32b * 32b -> 32b in 5 cycles)
- 32b popcount/extension/truncation unit
- 32b virtual addresses
- 16x4x128 entry, 2 way set-associative, software filled TLB
- 4 KiB pages
- 64 MiB physical address space (24b address x 32b data)
- up to 16 MiB SRAM
- up to 16 MiB I/O space
- up to 32 MiB pipeline-private, zero-wait SDRAM
Design Constraints
Since everyone in the homebrew CPU community has their own ideas of what kinds of technology are acceptable to use, here are my self-imposed restrictions and allowances:
- Backplane/card cage construction is preferred
- This facilitates building and testing smaller parts separately
- Blinkenlights are cool, but not particularly interesting at MHz frequencies
- 3.3V LVTTL/LVCMOS signalling is preferred
- Backplane signals must not exceed 3.3V (ignoring overshoot transients)
- 5V TTL outputs are allowed within a board, when paired with an 5V-tolerant receiver
- Differential LVPECL/LVDS signalling is allowed for clocks
- All boards should locally generate their own Vcc from a common 12V supply distributed by the backplane
- SMD footprints are fine
- >= 0.5mm pitch for QFP/QFN/(T)(S)SOP
- >= 0.8mm pitch for BGA
- Modern SRAM, dual-port SRAM, and SDRAM is fine to use
- Dedicated adder/multiplier/ALU ASICs are allowed
- But "not quite microprocessor" parts like Am2901 or Am29116/7 are not allowed (except in peripheral devices)
- FPGAs are not allowed
- Designing with HDLs feels more like work than fun for me, and all of the FPGA toolchains make me want to pull my hair out
- CPLDs and other programmable logic are allowed only if I have created the entire programming toolchain myself
- Designing for CPLDs (without HDLs) is extremely similar to designing for discrete logic, but simplifies board layout significantly, and often provides better timing characteristics
- Microcontrollers or other ASICs are allowed for bootstrapping or debugging purposes, or within peripheral devices
- Absolutely none within the data or control paths of the CPU itself
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100 nF | fp:C0402 | C8, C9, C10, C11, C12, C13, C14, C15, C16 |
| 5 | 22 µF | fp:C0805 | C1, C4, C5, C6, C7 |
| 2 | fp:TX25-120P-LT-H1E | J1, J2 | |
| 2 | 74LVC574 | fp:TSSOP-20 | U3, U4 |
| 2 | CY7C028V | fp:TQFP-100 (14mm) | U5, U6 |
| 2 | LC4128ZC | fp:BMC-149 | U7, U8 |
| 1 | 0 | fp:R0402 | R5 |
| 1 | 0.015 | fp:R1206 | R3 |
| 1 | 1.6 k | fp:R0402 | R4 |
| 1 | 10 k | fp:R0402 | R2 |
| 1 | 10 nF | fp:C0402 | C3 |
| 1 | 33.2 k | fp:R0402 | R1 |
| 1 | 330 nF | fp:C0402 | C2 |
| 1 | AP62300TWU | fp:SOT23-6 | U1 |
| 1 | EMC1702 | fp:QFN-12 (4mm x 4mm) | U2 |
| 1 | MMST3904 | fp:SOT323 | Q1 |
| 1 | NRS5040T3R3NMGJ | fp:NRS5040 | L1 |
More from bcrist/vera
3- 4 layers100 × 100 mm

- 4 layers100 × 100 mm

- 4 layers100 × 100 mm

Similar boards
- 2 layers24 × 38 mm

BSH Board
Bouni/BSH-Board
A board that interfaces the DBUS of several home appliances and brings them into Home-Assitant via ESPHome
75 parts65 - 4 layers99.1 × 91.4 mm

- 4 layers100 × 100 mm

- 4 layers100 × 50 mm

- 2 layers38.9 × 48.9 mm

- 4 layers100 × 100 mm

ModuCard mms extension pdw board
X-Lemon-X/ModuCard-mms-extension-pdw-board
This repository provides a template design for creating modules in the ModuCard system. Each module is designed to seamlessly interface with the ModuCard backplane, enabling a modular and expandable robotics platform.
161 parts - 2 layers152 × 57.6 mm

Videoslotadapter
LinuxJedi/AmigaRGBtoHDMI
LinuxJedi's designs for Amiga RGBtoHDMI boards.
22 parts127GPL-3.0 - 2 layers170.2 × 107.1 mm

Amiga Card Thru Hole
jasonsbeer/Amiga-HDMI-Through-Hole
Amiga Video Slot to HDMI Adapter
18 parts16GPL-3.0
Questions
How big is the At high PCB?
It measures 100 × 100 mm and has 4 copper layers, 1.59 mm thick.
What parts does the At high use?
33 parts, built around the AP62300TWU, 74LVC574AD, MMST3904 and NRS5040T3R3NMGJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the At high KiCad files?
From the bcrist/vera repository on GitHub, at the commit this page was made from: the board is boards/kicad/at_high/at_high.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the At high design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).