Skip to the content
2 layers65.1 × 28.6 mmPower, the printed circuit board in 3D

Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

Size
65.1 × 28.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
32
Nets
11
Pads
74
Tracks, vias
202, 0
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
1 Aug 2017
Updated
16 May 2023

Overview

Power is an open-source printed circuit board by b00lduck, from the b00lduck/esp32-audioplayer repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 65.1 × 28.6 mm with 32 parts on 11 nets, routed with 202 tracks and 0 vias.

It is built around the BC546 and BC327. Its parts include 14 resistors, 8 transistors, 4 capacitors and 4 connectors.

Main components

2

README

README.md

esp32-audioplayer

ESP32 based MP3 audio player with RFID control and case made from laser cutted plywood

!!! WORK IN PROGRESS !!! !!! not functional yet !!!

Used electronic hardware components:

  • ESP32 NodeMCU module
  • RFID-RC522 module (i.e. https://www.ebay.de/itm/172603664748)
  • VS1053B module with SD-slot (i.e. http://www.ebay.de/itm/272761135002)
  • Mifare classic 13.56MHz RFID cards (clones will do the job too, i.e. http://www.ebay.de/itm/122525501095)
  • Adafruit PowerBoost 500 Charger module
  • 3.7V LiPo battery
  • Class-D amplifier module
  • SD-Card (i.e. 4GB)
  • two Visaton FR7 (4 ohms) speakers
  • Custom main board (see kicad folder for layout)
  • Custom panel board (see kicad folder for layout)
  • 1x 220uF 35V
  • 1x 1uF 63V
  • 4x 100nF
  • 2x 47nF
  • 1x resistor ladder 4x 4.7k
  • 1x 10R
  • 1x 10kR
  • 1x 22kR
  • 4x WSL10 (2x5 header 2.54mm with notch)
  • 2x 2-pin header 2.54mm
  • 4x 4-pin header 2.54mm
  • some wire for airwires
  • some insulated wire 1mm², red and black (for internal connections)
  • 1x USB 2 Micro-B connector
  • 1x power switch
  • 1x USB 2 micro cable (for internal connection)
  • optional: MEMS gyroscope module
  • optional: 0.96 inch I2C OLED display

Wood parts:

  • 6 sheets, one for every side of the case
  • 2 distance rings for the speakers

Metal parts:

  • 2x 100x75x0.8mm aluminium sheet

3D-Printed parts:

  • 8x inner edge reinforcements
  • 4x M3x3 standoff
  • 8x M3*8 standoff (for main board)
  • 4x M3x11 standoff (for MP3 board)
  • 2x M3x6 standoff (for panel board)
  • 2x M3x4 standoff (for panel board)
  • 1x USB receptacle holder
  • 1x SD-Card slot box
  • 1x SD-Card slot cover

Screws

  • 4x M3x25 DIN 7991/ISO 10642 (countersunk allen bolt)
  • 32x M3 DIN 934/ISO 4042 (nut)
  • 8x M3 DIN 125/ISO 7089 (washer)
  • 8x M3x20 DIN 912/ISO 4762 (cylinder head allen bolt)
  • 2x M2x10 DIN 912/ISO 4762 (cylinder head allen bolt) for amp
  • 2x M2 DIN 934/ISO 4042 (nut)
  • 2x M2 DIN 125/ISO 7089 (washer)
  • 8x M3x?? DIN 7991/ISO 10642 (countersunk allen bolt) for speakers
  • 24x M3x15 DIN 7991/ISO 10642 (countersunk allen bolt) for inner corners

Used software:

  • VSCode with PlatformioIDE

Used Arduino Libraries:

  • SdFat 1.0.7
  • MFRC522 1.3.6

Port mapping

see src/config.h

3D printing

I used black 1.75 PETG filament for all parts. Layer height was 0.15mm at a printign speed of 30mm/s.

Parts

32
QtyValueFootprintReferences
1010kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R1, R3, R3, R4, R4, R6, R6, R7, R7
6BC546Package_TO_SOT_THT:TO-92L_HandSolderQ1, Q1, Q3, Q3, Q4, Q4
4100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R2, R5, R5
2100nCapacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mmC2, C2
2100nCapacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mmC1, C1
2BC327Package_TO_SOT_THT:TO-92L_HandSolderQ2, Q2
2Conn_01x02_MaleConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1, J1
2Conn_01x04_MaleConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2, J2

The 30 most common of 32 parts.

More from b00lduck/esp32-audioplayer

2
  • 2 layers100 × 75 mmAudioplayer, the printed circuit board in 3D

    Audioplayer

    b00lduck/esp32-audioplayer

    Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

    40 parts2GPL-3.0
  • 2 layers75.2 × 100.1 mmPanel, the printed circuit board in 3D

    Panel

    b00lduck/esp32-audioplayer

    Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

    26 parts2GPL-3.0

Similar boards

  • 2 layers80 × 50 mmProtection, the printed circuit board in 3D

    Protection

    FordPrfkt/KT88-Amp

    Tube Amplifier using KT88 Tubes based on BlackCat

    26 parts1
  • 2 layers85.1 × 35.6 mmSmartTherm, the printed circuit board in 3D

    SmartTherm

    Strooom/SmartTherm

    Controlling a Junkers heating (Eurostar ZWE24) with an IoT thermostat

    22 parts33
  • 4 layers150 × 100 mmUltimate LPS, the printed circuit board in 3D

    Ultimate LPS

    BTTLab/simple_and_affordable_lps

    Simple and affordable power supply

    97 parts27MIT
  • 2 layers108 × 88 mmSTRACHEY, the printed circuit board in 3D

    STRACHEY

    m0xpd/STRACHEY

    A Random Looping Sequencer for Eurorack

    126 parts25CC-BY-SA-4.0
  • 2 layers64 × 56 mmRpi dbt03, the printed circuit board in 3D

    Rpi dbt03

    bildschirmtext/rpi-dbt03

    Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter

    36 parts11MIT
  • 2 layers74.9 × 89.2 mmPictas, the printed circuit board in 3D

    Pictas

    bigbass1997/PICTAS

    Low-cost replay device for playing back Tool Assisted Speedruns on real hardware

    37 parts9
  • 2 layers66.7 × 36.8 mmKick, the printed circuit board in 3D

    Kick

    Wesemane-Industries/808-kick-eurorack

    808 kick (bass drum) for eurorack / modular synth

    57 parts8GPL-3.0
  • 2 layers78 × 108 mmEuclid+ Main Board, the printed circuit board in 3D

    Euclid+ Main Board

    m0xpd/EUCLIDplus

    EUCLID+ is a Clock Divider, Oscillator and Rhythm Sequencer for electronic music applications

    131 parts7CC-BY-SA-4.0

Questions

How big is the Power PCB?

It measures 65.1 × 28.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Power use?

32 parts, built around the BC546 and BC327. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Power KiCad files?

From the b00lduck/esp32-audioplayer repository on GitHub, at the commit this page was made from: the board is kicad/power/power.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Power design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).