Skip to the content
2 layers25 × 35 mmRJ45 Board, the printed circuit board in 3D

Aventen Formosa Sync GitHub page

Size
25 × 35 mm
Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
11
Pads
34
Tracks, vias
59, 0
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
10 Sep 2023
Updated
17 May 2026

Overview

RJ45 Board is an open-source printed circuit board by avencan, from the avencan/Aventen-Formosa-Sync repository on GitHub, published under the MIT licence. It is a 2-layer board of 25 × 35 mm with 5 parts on 11 nets, routed with 59 tracks and 0 vias.

It is built around the RJ45. Its parts include 2 resistors, 2 connectors and 1 capacitor. It belongs with the radio and wireless boards of this library.

Main components

1

README

README.md

⚠️ This board has been superseded

Aventen Formosa Sync has been replaced by the Aventen Kypros — a completely redesigned board with WiFi 6, HDMI output, Gigabit Ethernet, native Zigbee/Thread/Matter, on-board audio codec, and 2× the compute power.

👉 See the Kypros → github.com/avencan/Aventen-Kypros 👉 Join the waitlist → aventeninnovations.com


Aventen Formosa Sync

Aventen Formosa Sync

The board that started it all.

Status Crowd Supply Built in Britain [blocked]


Introduction

The Aventen Formosa Sync was Aventen's first development board — a high-performance board equipped with a 600MHz RT1060 MCU (overclockable to 1GHz under the right conditions), built-in WiFi 5 + Bluetooth with audio, USB OTG, RGB LEDs, USB-C connectivity, and comprehensive battery management.

Designed for IoT makers, professionals, and industrial solutions — it offered a compact, breadboardable form factor with serious performance.


Specs

FeatureDetail
MCUNXP MIMXRT106SDVL6B — ARM Cortex-M7 @ 600MHz (overclockable to 1GHz)
PSRAM8MB
Flash16MB
WiFiWiFi 5 — Murata Type 1ZM
BluetoothBT 5.0
SD CardBuilt-in MicroSD slot
USBUSB-C
Ethernet10/100 via LAN8720A
LEDsRGB + status LED
GPIO35 header pins
DebugSWD/JTAG
PowerBattery (JST) + USB-C LiPo charging
ExtrasChip antenna + IPX U.FL · Aux LDO 1A · RF switch

Add-on Boards

RJ45 LAN8720A Ethernet Board: github.com/avencan/Aventen-Formosa-Sync/tree/main/RJ45


Status

Formosa Sync reached prototype stage and confirmed first prototype. It was covered by Hackster.io and launched a Crowd Supply campaign. Development was paused in favour of the next-generation Kypros board.


What Came Next

We built Formosa Sync. Then we asked: what if we threw out every compromise and started over with the RT1176 — before anyone else did?

That's Kypros.

Formosa SyncKypros
CPURT1060 @ 600MHzRT1176 @ 1GHz + 400MHz
WiFiWiFi 5WiFi 6 (601Mbps)
HDMI❌✅ 1080p
Ethernet10/100MbpsGigabit
Zigbee/Thread/Matter❌✅ Native
Audio Codec❌✅ SGTL5000 (98dB SNR)
Ultrasonic Mic❌✅ 80kHz
LiPo Native✅✅
Form FactorBreadboardable69×18mm

👉 See the Kypros → github.com/avencan/Aventen-Kypros


Built in Britain 🇬🇧 — Loved everywhere.

Aventen Innovations Ltd — Eastbourne, UK

© 2026 Aventen Innovations Ltd · aventeninnovations.com

Parts

5
QtyValueFootprintReferences
2270RResistor_SMD:R_0201_0603MetricR1, R2
110uFCapacitor_SMD:C_0402_1005MetricC1
1JST_RJ45Connector_PinHeader_1.27mm:PinHeader_2x04_P1.27mm_VerticalJ3
1RJ45Connector_RJ:RJ45_Bel_SI-60062-FJ1

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 4 layers84 × 82 mmToad, the printed circuit board in 3D

    Toad

    travisgoodspeed/goodfet

    An embedded bus adapter for various microcontrollers and radios.

    241 parts333
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99
  • 2 layers50 × 55.4 mmCasserole, the printed circuit board in 3D

    Casserole

    puddly/casserole

    Control GE appliances

    23 parts94Apache-2.0
  • 2 layers67.9 × 47.8 mmPlatine, the printed circuit board in 3D

    Platine

    nv1t/standing-desk-interceptor

    I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project

    11 parts52CC0-1.0
  • 4 layers90 × 75 mmCM4 2 Backup, the printed circuit board in 3D

    CM4 2 Backup

    olvint/CM4-NAS-MiniPCIE

    Raspberry Pi CM4 based NAS solution board

    21 parts51
  • 4 layers73.9 × 84.5 mmAei, the printed circuit board in 3D

    Aei

    Severson-Group/AMDC-Hardware

    Circuit board designs for controlling advanced motor systems

    54 parts51
  • 2 layers99 × 60 mmPwr, the printed circuit board in 3D

    Pwr

    mfkiwl/KiwiSDR_PCB

    KiCAD PCB files for KiwiSDR project including active antenna and bias tee

    64 parts46

Questions

How big is the RJ45 Board PCB?

It measures 25 × 35 mm and has 2 copper layers, 1.6 mm thick.

What parts does the RJ45 Board use?

5 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the RJ45 Board KiCad files?

From the avencan/Aventen-Formosa-Sync repository on GitHub, at the commit this page was made from: the board is RJ45/RJ45 Board/RJ45 Board.kicad_pcb and its schematic RJ45/RJ45 Board/RJ45 Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the RJ45 Board design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).