

Design files
My design files. Abandon all hope ye who enter here.
- Size
- 31.1 × 20.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 22
- Nets
- 19
- Pads
- 78
- Tracks, vias
- 232, 15
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 26 May 2017
- Updated
- 13 Dec 2022
Overview
Design files is an open-source printed circuit board by aspro648, from the aspro648/KiCad repository on GitHub. It is a 2-layer board of 31.1 × 20.3 mm with 22 parts on 19 nets, routed with 232 tracks and 15 vias.
It is built around the ATTINY84A-PU and TC78H651FNG(O,EL). Its parts include 7 connectors, 6 resistors, 3 capacitors, 2 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATTINY84A-PU
DIP-14-40℃~+85℃ 1.8V~5.5V 10bit 12 20MHz 512Byte 512Byte 8 Bit 8KB AVR Built-in FLASH DIP-14 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)TC78H651FNG(O,EL)
TSSOP-16-40℃~+105℃ 1.5A 1.8V~6V 2 220mΩ Bipolar Driver Yes TSSOP-16 Stepper Motor Driver ROHSToshibaStepper Motor Driver
README
README.mdKiCad
My design files. Abandon all hope ye who enter here.
Parts
22| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10K | footprints:R_0603_HandSoldering | R3, R4, R5, R6, R8, R10 |
| 1 | 0.1uF | footprints:C_0603_HandSoldering | C1 |
| 1 | 10uF | Capacitors_SMD:C_1206_HandSoldering | C2 |
| 1 | 1uF | footprints:C_0805_HandSoldering | C3 |
| 1 | ACCEL | footprints:Pot_Bourns_TC33 | RV2 |
| 1 | ATTINY84 | footprints:SOIC-14_3.9x8.7mm_Pitch1.27mm | U2 |
| 1 | AVR-ISP-6 | footprints:Pin_Header_Straight_2x03_Pitch2.54mm | CON1 |
| 1 | BATT | footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J1 |
| 1 | Diode | footprints:D_SOD-323_HandSoldering | D1 |
| 1 | JMP | footprints:Jumper | JP1 |
| 1 | MTR_1 | footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J3 |
| 1 | MTR_2 | footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J5 |
| 1 | SIG_1 | footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J2 |
| 1 | SPEED | footprints:Pot_Bourns_TC33 | RV1 |
| 1 | SR04 | footprints:Pin_Header_Straight_1x04_Pitch2.54mm | J6 |
| 1 | TC78H651FNG | footprints:TSSOP-16_4.4x5mm_Pitch0.65mm | U1 |
| 1 | VCC | footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J4 |
More from aspro648/KiCad
12- 2 layers86.4 × 53.3 mm

- 2 layers64 × 40 mm

- 2 layers86.4 × 53.3 mm

- 2 layers128 × 75 mm

- 2 layers128 × 75 mm

- 2 layers42 × 18 mm

- 2 layers80 × 38 mm

- 2 layers132 × 75 mm

- 2 layers42 × 18 mm

- 2 layers90 × 64 mm

- 2 layers69.8 × 12.5 mm

- 2 layers64.8 × 50.8 mm

Similar boards
- 2 layers57 × 57 mm

Quiet orbit qo r1-usb c four light ambient lamp board
copperheadhq/copperhead-quiet-orbit
USB-C four-light ambient lamp, 57 mm, ATtiny84A hardware PWM. Designed with copperhead. Never built: do not order expecting it to work.
27 parts3 - 2 layers96.5 × 25.4 mm

- 2 layers94 × 63.8 mm

TinySensorv1
arcadien/tinySensor
Firmware and generic board for low-power environment sensors
45 parts2MIT - 2 layers55.2 × 40.6 mm

- 2 layers35 × 28 mm

Volvo240pcb
pddenhar/Volvo_240_Info_Display
OLED dashboard module for the Volvo 240 displaying battery voltage, speed, and RPM.
18 parts2 - 2 layers90 × 40 mm

Plate
BryceVandegrift/hot-plate
A DIY PCB hot plate that uses through hole components
30 parts1CERN-OHL-W-2.0 - 2 layers92 × 45 mm

L6 - P2
AhmedAtefNasr/PCB_Course-IMT_school
Here's the repo for Assignments & projects of PCB course from IMT school
49 parts - 2 layers46 × 66 mm

Door sensor schaltplan
Brawn1/ATTiny-Door-Sensor
Door Sensor Battery based with Attiny84 and HC-12 Sender
19 parts
Questions
How big is the Design files PCB?
It measures 31.1 × 20.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Design files use?
22 parts, built around the ATTINY84A-PU and TC78H651FNG(O,EL). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Design files KiCad files?
From the aspro648/KiCad repository on GitHub, at the commit this page was made from: the board is projects/Attiny/Attin85_HBridge R2/design_files/project.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Design files design in my own project?
Its repository states no licence, so its author keeps all rights: ask aspro648 before reusing the design.