
Quiet orbit qo r1-usb c four light ambient lamp board
copperheadhq/copperhead-quiet-orbit
USB-C four-light ambient lamp, 57 mm, ATtiny84A hardware PWM. Designed with copperhead. Never built: do not order expecting it to work.

OLED dashboard module for the Volvo 240 displaying battery voltage, speed, and RPM.
Volvo240pcb is an open-source printed circuit board by pddenhar, from the pddenhar/Volvo_240_Info_Display repository on GitHub. It is a 2-layer board of 35 × 28 mm with 18 parts on 19 nets, routed with 133 tracks and 10 vias.
It is built around the ATTINY84A-PU and L7805CV. Its parts include 8 resistors, 3 capacitors, 3 connectors, 2 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
This is a OLED dashboard module for the Volvo 240 that provides speedometer, tachometer, and battery voltage.
The PCB layout is in KiCAD. A BOM used to purchase board components at Digikey can be found in the PCB Layout directory as well.

The back of the dashboard cluster has an open collector signal for the speedometer pulses (reverse engineered with help from http://cleanflametrap.com/speedo.html). This already has a 12V pullup on it, so all you need to do is connect a lead to the output.
The tachometer signal can be connected to the red and white wire present behind the gauge cluster (not connected in 240s without a tach from the factory).
12V Power and ground can be spliced into the 3-pin power cable for the gauge cluster.
The Arduino code is compiled for the ATtiny84. You will need the ATTinyCore board library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10k | Resistors_SMD:R_0805_HandSoldering | R1, R2, R3 |
| 3 | 25k | Resistors_SMD:R_0805_HandSoldering | R4, R5, R6 |
| 1 | 0.1u | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 0.33u | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 1000p | Capacitors_SMD:C_0805_HandSoldering | C3 |
| 1 | 15EDGK-3.81-05P | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_6-G-3.81_1x06_P3.81mm_Vertical | J1 |
| 1 | 1k | Resistors_SMD:R_0805_HandSoldering | R8 |
| 1 | 20k | Resistors_SMD:R_0805_HandSoldering | R7 |
| 1 | ATTINY84A-PU | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 1 | BZX84Cxx | Diode_SMD:D_SOT-23_ANK | D1 |
| 1 | Display | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | ISP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | L7805CV | digikey-footprints:TO-220-3 | U1 |
| 1 | PWR | Diodes_SMD:D_0805 | D2 |

copperheadhq/copperhead-quiet-orbit
USB-C four-light ambient lamp, 57 mm, ATtiny84A hardware PWM. Designed with copperhead. Never built: do not order expecting it to work.


arcadien/tinySensor
Firmware and generic board for low-power environment sensors


BryceVandegrift/hot-plate
A DIY PCB hot plate that uses through hole components

AhmedAtefNasr/PCB_Course-IMT_school
Here's the repo for Assignments & projects of PCB course from IMT school

Brawn1/ATTiny-Door-Sensor
Door Sensor Battery based with Attiny84 and HC-12 Sender

It measures 35 × 28 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the ATTINY84A-PU and L7805CV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the pddenhar/Volvo_240_Info_Display repository on GitHub, at the commit this page was made from: the board is PCB Layout/volvo240pcb/volvo240pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask pddenhar before reusing the design.