4 layers200 × 41 mm
4 layers171.5 × 29.5 mm
Frederic ANN
artandtechspace/Frederic-ANNAnalog Neural Network
- Size
- 171.5 × 29.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 170
- Nets
- 82
- Pads
- 537
- Tracks, vias
- 1,258, 285
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Dec 2024
- Updated
- 15 Jan 2025
Overview
Frederic ANN is an open-source printed circuit board by artandtechspace, from the artandtechspace/Frederic-ANN repository on GitHub. It is a 4-layer board of 171.5 × 29.5 mm with 170 parts on 82 nets, routed with 1,258 tracks and 285 vias.
It is built around the 1N4148W-7-F-CN. Its parts include 70 capacitors, 44 resistors, 30 ICs, 24 connectors and 2 diodes.
Main components
1README
README.mdFrederic-ANN
Analog Neural Network
Parts
170| Qty | Value | Footprint | References |
|---|---|---|---|
| 70 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +54 |
| 30 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R10, R11, R13, R14, R16, R17, R19, R20, R22, R23, R25, R26, R27, R28 +14 |
| 20 | OPA196IDBVR | SamacSys_Parts:SOT95P280X145-5N | IC1, IC2, IC10, IC12, IC13, IC15, IC16, IC18, IC19, IC21, IC22, IC24, IC26, IC27, IC28, IC29 +4 |
| 10 | Conn_01x02 | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1, J2, J3, J4, J5, J6, J7, J8, J9, J24 |
| 9 | MCP41HV51-503E_ST | SamacSys_Parts:SOP65P640X120-14N | IC3, IC5, IC8, IC11, IC14, IC17, IC20, IC23, IC30 |
| 8 | 12.4k | Resistor_SMD:R_0805_2012Metric | R3, R6, R9, R12, R15, R18, R21, R24 |
| 8 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10, J11, J12, J13, J14, J15, J16, J17 |
| 4 | 0 | Resistor_SMD:R_0805_2012Metric | R33, R39, R45, R46 |
| 2 | 1N4148W-7-F | SamacSys_Parts:SOD3716X145N | D1, D2 |
| 1 | 18k | Resistor_SMD:R_0805_2012Metric | R44 |
| 1 | 3.9k | Resistor_SMD:R_0805_2012Metric | R42 |
| 1 | 74HC595D_BJ_ | SamacSys_Parts:SOIC127P600X175-16N | IC25 |
| 1 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Horizontal | J22 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J23 |
| 1 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J19 |
| 1 | Conn_01x04_Pin | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J18 |
| 1 | Conn_01x08_Pin | Connector_JST:JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J21 |
| 1 | Conn_02x04_Top_Bottom | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J20 |
More from artandtechspace/Frederic-ANN
1Similar boards
- 2 layers368.3 × 254 mm
- 2 layers79 × 89 mm
Bms v1
azerimaker/BMS_3-5S
3-5S Battery Management System based on TI bq76920 IC and MSP430 uC.
175 parts22 - 2 layers128 × 55 mm
MotoHUD
wiciu15/motoHUDsch
KiCad Schematic and PCB for motoHUD (https://github.com/wiciu15/motoHUDini)
121 parts16 - 2 layers178 × 711 mm
- 2 layers175 × 115 mm
Laser Controllerv2 only for pcb test
Andre1Becker/GalvOS
Open-source ESP32-S3 laser show controller — built to replace proprietary OEM controllers in RGB galvo laser projectors
122 parts11GPL-3.0 - 2 layers80 × 95 mm
LaserBoard
matthewSorensen/pewpew-laserboard
LaserBoard is an open source controller for fiber laser marking systems, based around a Teensy 4.1 MCU board. LaserBoard provides a USB interface compatible with most low-cost fiber laser sources and XY-100-speaking…
123 parts10CERN-OHL-S-2.0 - 4 layers70 × 70 mm
Blue interface board
BetzDrive/interface-board
Power and signal conditioning board for the Betz Drive system
130 parts5 - 2 layers50 × 70 mm
Time2time
Resaj/time2time
Chronometer with partials measurement for the line-following competitions
97 parts5
Questions
How big is the Frederic ANN PCB?
It measures 171.5 × 29.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Frederic ANN use?
170 parts, built around the 1N4148W-7-F-CN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Frederic ANN KiCad files?
From the artandtechspace/Frederic-ANN repository on GitHub, at the commit this page was made from: the board is V4.5/V4.5/V4.5.kicad_pcb and its schematic V4.2/Weights V4.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Frederic ANN design in my own project?
Its repository states no licence, so its author keeps all rights: ask artandtechspace before reusing the design.