

A unique clock made with thermochromic paint
- Size
- 93.8 × 39.5 mm
- Copper layers
- 2
- Thickness
- 0.8 mm
- Parts
- 58
- Nets
- 65
- Pads
- 203
- Tracks, vias
- 383, 44
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 9 Mar 2025
- Updated
- 3 Oct 2025
Overview
Control is an open-source printed circuit board by anneosaur, from the anneosaur/paper-sunshine-clock repository on GitHub. It is a 2-layer board of 93.8 × 39.5 mm with 58 parts on 65 nets, routed with 383 tracks and 44 vias.
It is built around the ATMEGA328PB-AU, DS18B20U and DS3231MZ/V+, with the DMN2020LSN-7-VB, SI2393DS-T1-GE3-HXY and 3000TR among its other parts. Its parts include 22 resistors, 10 transistors, 7 capacitors, 6 fuses and 4 ICs. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
8ATMEGA328PB-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)DS18B20U
MSOP-8-55℃~+125℃ 12bit 2.5V~5.5V 400ms 750nA Single-bus ±0.4℃ MSOP-8 Temperature Sensors ROHSUMWTemperature SensorsDS3231MZ/V+
SOIC-8-40℃~+85℃ 2.3V~5.5V Built-in I2C Temperature compensation、Backup power management and battery charging、Alarm function、Locking and tamper-proof、Periodic interrupt output SOIC-8 Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time ClocksDMN2020LSN-7-VB
SOT-23(TO-236)MOSFETsVBsemi ElecSI2393DS-T1-GE3-HXY
SOT-23-3LMOSFETsHXY MOSFET3000TR
-- ROHSKeystone ElectronicsBatteryConnectorAP2210N-3.3TRG1
SOT-23-40℃~+125℃@(Tj) 1 13.2V 1uA 250mV@(300mA) 3.3V 300mA 75dB@(100Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSB4125-GF-A-0190
SMD-30℃~+85℃ 1 20 thousand cycles 3A 48V 6P Black Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
README
README.mdpaper sunshine clock
This project is a clock that tells time in a unique way. The face of the display looks like the sun with 12 rays representing 12 o’clock to 11 o’clock, going clockwise, which turn from black to yellow as the day progresses. Each ray is divided up into half hour segments, so the clock is able to tell you the current half hour. For example in the photo above, the clock is reading between 9 o’clock and 9:30. The display is made out of paper and uses thermochromic paint that changes color with heat. There is a thin circuit board behind the paper which provides the warmth to activate the thermochromic paint, changing the color of the rays. The clock also has Sparkle Mode, which will turn on a random ray every 10 seconds. It provides an entertaining show as the rays turn on and fade away (see Videos below). The enclosure is 3D printed.
https://github.com/user-attachments/assets/e0f1c668-d030-4747-b99e-f9c4dc16aae8
Reading the clock
The clock has 12 rays, representing 12 hours from 12 o'clock to 11 o'clock. Each ray is divided up into half hour segments. As each half hour of the day passes, the corresponding segment will turn from black to yellow. The clock face is fully yellow between 11:30-11:59. At 12:00, it'll reset.
How it works
The clock works by using thermochromic paint screen printed onto a piece of Japanese awagami paper. Behind that, is a flex PCB with large resistors mounted on the back. These resistors can be selectively turned on, warming up the paper and activating the thermochromic paint. Each ray on the PCB is a copper pour used to spread and hold heat from the resistors. It was designed using Python and an SVG drawing library, and converted into a KiCad footprint.
The control board is driven by an Atmega328PB and uses a DS3231MZ RTC for accurate time keeping. A coin cell battery is used to keep track of time even when the clock is unpowered. The time is initially set when programming the clock, and can be changed in +/- 30 minute increments using the two buttons on the back.
It uses a multiplexing system which allows the 24 segments to be controlled with 10 connections. The rays of the clock are divided in 3 groups, with 4 rays each. Each group has a top and bottom ground connection connecting the rays (allowing the half hour segments to be individually controlled). The “similar” rays of each group (e.g., the first ray of each group, the second ray of each group, etc) have a shared 5v connection. So for example, to turn on the segment representing the first half hour of 12 o’clock, ground the bottom connection of the first group and apply 5v to the first ray.
For safety (since we’re applying heat to paper here), I used an eFuse to clamp the input voltage at 5v. There are also SMD fuses to prevent against excessive current going through the segments.
In order to keep the rays at the proper temperature to activate the thermochromic paint (ideally around 90-95 F / 32-35 C), a temperature sensor reads the ambient temperature and will PWM the display to maintain a reasonably consistent temperature. This actually got a bit complicated, since the heat from the display would warm up the back compartment where the control PCB is and influence the temperature sensor. Fortunately, the temperature increases were fairly predicable and could be compensated for. From testing, the clock works well in room temperatures between 65-80 F / 18-27 C.
Videos
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R13, R14, R17 |
| 6 | DMN2020LSN-7 | Clock:SOT95P285X130-3N | Q5, Q6, Q7, Q8, Q9, Q10 |
| 6 | Fuse | Fuse:Fuse_0603_1608Metric | F1, F2, F3, F4, F5, F6 |
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C8 |
| 4 | SI2393DS-T1-GE3 | Clock:SOT95P237X112-3N | Q1, Q2, Q3, Q4 |
| 3 | 4.7k | Resistor_SMD:R_0805_2012Metric | R11, R12, R20 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C1, C6 |
| 2 | 400k | Resistor_SMD:R_0805_2012Metric | R21, R22 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R15, R16 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 3000TR | Clock:BAT_3000TR | BT1 |
| 1 | 500 | Resistor_SMD:R_0805_2012Metric | R19 |
| 1 | 60 | Resistor_SMD:R_0805_2012Metric | R18 |
| 1 | AP2210N-3.3TRG1 | Clock:SOT95P282X145-3N | D5 |
| 1 | ATmega328PB-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U6 |
| 1 | Conn_01x10_Pin | Clock:CON10_SMT-RA_FCC-FPC2 | J3 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_1.27mm:PinHeader_2x04_P1.27mm_Vertical | J4 |
| 1 | DS18B20U | Package_SO:MSOP-8_3x3mm_P0.65mm | U1 |
| 1 | DS3231MZ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | Sparkle | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | TPS259621DDAT | Clock:IC_TPS259621DDAT | U3 |
| 1 | Time Adj | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | USB4125-GF-A-0190 | Clock:GCT_USB4125-GF-A-0190_REVA2 | J2 |
| 1 | Val** | Clock:control_pcb_outline | Ref** |
Similar boards
- 2 layers184 × 107.5 mm

- 2 layers27.4 × 58.7 mm

Lc29h mikrobus PCB
i2hm/micro_climate_station
Open the KiCad project using KiCad 7 and above.
48 parts3 - 4 layers72 × 55 mm

Exhaust mic
HasiKe/Exhaust-Mic
Motorcycle Exhaust and Intake Microphone for best soud on Videos.
135 parts - 2 layers40 × 30 mm

0005 RTC Module DS1307
memetteminarslan/0005_RTC_Module_DS1307
You are seeing a large number of widely used RTC modules in electronic development kits. More information coming soon...
9 parts - 4 layers95.5 × 95 mm

TallyLight Panel
SamuelEames/TallySystems
Tally light system for vMix using Arduino USB MIDI controller, transmitting tally light data to receiver modules on cameras using NRF24L01 radios
192 parts - 2 layers98 × 60 mm

NightStandClock
LucasCanete/BasicClock
A clock that shows the time and additionally the temperature and humidity
64 parts - 4 layers74 × 36.3 mm

Loudcardsdevice
gelotek-com/Anki-In-Hardware
Building a physical flashcard device inspired by Anki and spaced repetition.
87 parts2 - 4 layers49 × 80 mm

70MHz Soil Sensor
jhns-de/70MHz-Soil-Sensor
Soil moisture and electrical conductivity (EC) sensor based on 70 MHz impedance measurement, developed as part of my master’s thesis.
130 parts2
Questions
How big is the Control PCB?
It measures 93.8 × 39.5 mm and has 2 copper layers, 0.8 mm thick.
What parts does the Control use?
58 parts, built around the ATMEGA328PB-AU, DS18B20U, DS3231MZ/V+ and DMN2020LSN-7-VB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Control KiCad files?
From the anneosaur/paper-sunshine-clock repository on GitHub, at the commit this page was made from: the board is pcbs/control/control.kicad_pcb and its schematic pcbs/cable/cable.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Control design in my own project?
Its repository states no licence, so its author keeps all rights: ask anneosaur before reusing the design.