

Karabas mini
Karabas Go Mini PCB
- Size
- 70 × 69.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 222
- Nets
- 372
- Pads
- 1,329
- Tracks, vias
- 5,222, 685
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 5 Jun 2024
- Updated
- 5 Nov 2026
Overview
Karabas mini is an open-source printed circuit board by andykarpov, from the andykarpov/karabas-mini-pcb repository on GitHub. It is a 4-layer board of 70 × 69.8 mm with 222 parts on 372 nets, routed with 5,222 tracks and 685 vias.
It is built around the RP2040, SAM2695 and ESP-12E, with the FE1.1S, TPD12S016RKTR and W25Q128JVSIQ among its other parts. Its parts include 96 capacitors, 59 resistors, 20 ICs, 13 connectors and 5 diodes. It belongs with the ESP8266, RP2040 and FPGA and CPLD boards of this library.
Main components
12RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)SAM2695
QFN-48-EP_6x6-25℃~+70℃ 2.7V~3.6V Processor、Encoder/decoder QFN-48-EP(6x6) Audio Interface ICs ROHSDREAMAudio Interface ICsESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi ModulesFE1.1S
SSOP-28USB 2.0 USB Hub SSOP-28 USB Converters ROHSTerminus TechUSB ConvertersTPD12S016RKTR
UQFN-24(2x4)-40℃~+85℃ 3.4Gbps 4.5V~5.5V I2C UQFN-24(2x4) Interface - Specialized ROHSTexas InstrumentsInterface - SpecializedW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHLM1117MP-3.3
SOT-2230℃~+125℃@(Ta) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA 99uVrms Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsIS61WV20488BLL-10TLI
TSOP-44-10.2mm-40℃~+85℃ 10ns 16Mbit 2.4V~3.6V 35mA Auto power-down function TSOP-44-10.2mm SRAM ROHSISSISRAM24LC08B/P
PDIP-8-40℃~+125℃ 1,000,000 cycles 2.5V~5.5V 200 Years 400kHz 5ms 8Kbit Hardware write protection function、Noise suppression function I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROMDS3231MZ/V+
SOIC-8-40℃~+85℃ 2.3V~5.5V Built-in I2C Temperature compensation、Backup power management and battery charging、Alarm function、Locking and tamper-proof、Periodic interrupt output SOIC-8 Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time ClocksLM311
SOP-80℃~+70℃ 1 1.7nA 2.4mA 200ns 2mV 36V 45nA 5V~30V TTL、CMOS ±15V SOP-8 Comparators ROHSGcoreComparatorsMT48LC16M16A2TG
TSOP-54TSOP-54 DRAM ROHSMicron TechDRAM
Parts
222| Qty | Value | Footprint | References |
|---|---|---|---|
| 56 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C11, C12, C13, C14, C15, C16, C17, C19, C20, C22, C23, C24, C25, C26, C101 +40 |
| 20 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R13, R14, R16, R17, R18, R19, R20, R25, R26, R27, R28, R47, R48, R49 +4 |
| 16 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R5, R6, R21, R22, R23, R24, R38, R39, R42, R45, R46, R53, R56, R60 |
| 13 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C7, C66, C67, C69, C70, C71, C90, C91, C96, C99, C104, C105 |
| 7 | 470 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8, R30, R31, R43, R44, R54 |
| 6 | 27 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12, R35, R36, R57, R58, R59 |
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C29, C31, C33, C35 |
| 4 | 22pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C93, C94 |
| 4 | 2n2 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C62, C64, C98, C100 |
| 4 | MountingHole | MountingHole:MountingHole_3mm_Pad_Via | H1, H2, H3, H4 |
| 3 | 100uF | footprints:CP_EIA-7343-31_Kemet-D-uni | C60, C61, C75 |
| 3 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1, Y2, Y3 |
| 3 | 2u2 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C63, C65, C86 |
| 3 | 4n7 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C87, C88, C89 |
| 3 | 5k1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R33, R34, R40 |
| 3 | LM1117MP-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1, U12, U18 |
| 2 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B_Pad1.50x2.35mm_HandSolder | C18, C21 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C8 |
| 2 | 2x USB A | footprints:USB_A_Wuerth_61400826021_Horizontal_Stacked_oval | J1, J2 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R11 |
| 2 | BC856 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP5, TP8 |
| 2 | IS61WV20488BLL-10TLI | Package_SO:TSOP-II-44_10.16x18.41mm_P0.8mm | U9, U10 |
| 2 | uSD card | footprints:Conn_uSDcard | J4, J5 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R32 |
| 1 | 24LC08B | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | 2k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 300 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R41 |
| 1 | 33k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R37 |
| 1 | 3V | footprints:BAT_S8411-45R | BT1 |
| 1 | 3n3 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C54 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C38 |
| 1 | 50 MHz | Oscillator:Oscillator_SMD_SeikoEpson_SG8002CA-4Pin_7.0x5.0mm | X1 |
| 1 | 5V | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J9 |
| 1 | 6V 2A | Fuse:Fuse_1210_3225Metric_Pad1.42x2.65mm_HandSolder | F1 |
| 1 | Activitty | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D2 |
| 1 | Audio | footprints:AUDIO_JACK_3.5MM_SMD_TRRS_rounded_mixed | J8 |
| 1 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D5 |
| 1 | Boot | footprints:SW_SPST_PTS810_handsoldering | BTN1 |
| 1 | CLK | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | DS3231MZ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | ESP-12E | RF_Module:ESP-12E | U17 |
| 1 | FE1.1s | footprints:SSOP-28_3.9x9.9mm_P0.635mm-long | U4 |
| 1 | FT812 | Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP5.9x5.9mm | U8 |
| 1 | HDMI_A_1.4 | Connector_HDMI:HDMI_A_Molex_208658-1001_Horizontal | J3 |
| 1 | I2C | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | P4 |
| 1 | IO | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | IO0 | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | IO2 | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | IO3 | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | Keyboard | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D1 |
| 1 | LM1117MP-1.2 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U13 |
| 1 | LM311 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U14 |
| 1 | LOGO | footprints:karabas-go-small-silk2 | G*** |
| 1 | MT48LC16M16A2TG | Package_SO:TSOP-II-54_22.2x10.16mm_P0.8mm | U11 |
| 1 | Magic | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | BTN3 |
| 1 | PCM1808PWR | footprints:SOP65P640X120-14N | U16 |
| 1 | PCM5102A | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U25 |
| 1 | RP2040 | RP2040_minimal:RP2040-QFN-56 | U3 |
| 1 | Reset | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | BTN4 |
| 1 | Reset | footprints:SW_SPST_PTS810_handsoldering | BTN2 |
| 1 | SAM2695 | Package_DFN_QFN:QFN-48-1EP_6x6mm_P0.4mm_EP4.2x4.2mm | U15 |
| 1 | SD 1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D3 |
| 1 | SD 2 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D4 |
| 1 | TCK | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | TDI | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | TDO | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | TMS | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | TPD12S016RKTR | footprints:IC_TPD12S016RKTR | U19 |
| 1 | Tape In/Out | footprints:AUDIO_JACK_3.5MM_SMD_TRRS_rounded_mixed | J6 |
| 1 | Type-C right angle "flag" type | TypeC:CHINA_2169890001 | J7 |
| 1 | VCC | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
| 1 | XC6SLX25-FTG256 | Package_BGA:BGA-256_17.0x17.0mm_Layout16x16_P1.0mm_Ball0.5mm_Pad0.4mm_NSMD | U7 |
| 1 | uBUS1 | Connector_PinHeader_1.27mm:PinHeader_2x04_P1.27mm_Vertical | P1 |
| 1 | uBUS2 | Connector_PinHeader_1.27mm:PinHeader_2x08_P1.27mm_Vertical | P2 |
| 1 | uBUS3 | Connector_PinHeader_1.27mm:PinHeader_2x08_P1.27mm_Vertical | P3 |
More from andykarpov/karabas-mini-pcb
5- 2 layers70 × 69.8 mm

- 2 layers70 × 69.8 mm

- 2 layers70 × 69.8 mm

- 2 layers70 × 69.8 mm

- 2 layers70 × 69.8 mm

Similar boards
- 4 layers101.6 × 147.3 mm

- 6 layers160 × 101.4 mm

- 2 layers100 × 100 mm

Zxuno1010
UzixLS/zxuno1010-board
10x10cm PCB variant of ZX-UNO project for G738/G706 enclosure
233 parts23MIT - 4 layers100 × 100 mm

- 6 layers50 × 42 mm

- 2 layers100 × 100 mm

Mist1010
UzixLS/mist1010-board
10x10cm PCB variant of MIST FPGA project for G738/G706 enclosure
271 parts43MIT - 4 layers92.2 × 44 mm

Karabas megabuzz
andykarpov/karabas-megabuzz
A minimalistic FPGA soundcard for ZX Spectrum
177 parts9MIT - 4 layers180 × 110 mm

PETER
dennowiggle/Retro-PETER
3.3V Retro computer project => FPGA + RCBUS + CPU boards making a custom system.
419 parts4LGPL-2.1
Questions
How big is the Karabas mini PCB?
It measures 70 × 69.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Karabas mini use?
222 parts, built around the RP2040, SAM2695, ESP-12E and FE1.1S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Karabas mini KiCad files?
From the andykarpov/karabas-mini-pcb repository on GitHub, at the commit this page was made from: the board is karabas-mini.kicad_pcb and its schematic fpga.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Karabas mini design in my own project?
Its repository states no licence, so its author keeps all rights: ask andykarpov before reusing the design.