Skip to the content
2 layers233.5 × 181.5 mmDisplay, the printed circuit board in 3D

HDL, Hardware & Software Development project to playback a video with sound and learn while doing so.

Size
233.5 × 181.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
774
Nets
56
Pads
1,596
Tracks, vias
2,566, 0
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
28 Sep 2023
Updated
22 Oct 2025

Overview

Display is an open-source printed circuit board by alpyen, from the alpyen/fpga-mediaplayer repository on GitHub. It is a 2-layer board of 233.5 × 181.5 mm with 774 parts on 56 nets, routed with 2,566 tracks and 0 vias.

Its parts include 768 diodes and 2 connectors. It belongs with the fPGA and programmable logic and lEDs and displays boards and the FPGA and CPLD boards of this library.

README

README.md

fpga-mediaplayer - learning FPGA development

Hi there, and welcome to my FPGA project to deep dive into FPGA development and everything around it.

Watch a demo of this project on YouTube by clicking on this picture!

Navigation

  1. Introduction
  2. Project Goal
  3. Top Level Overview
  4. Documentation

Introduction

This is a beginner project on hardware development with FPGAs and VHDL to create a system that can play audio and video through an FPGA.

A FPGA development board -- here a Digilent Basys3 -- fetches audio and video data stored on the on-board flash memory chip, decodes them and drives a Digilent i2s2-PMOD for audio output and a custom designedLED matrix as the video display.

Originally the idea was to drive one of these standard Arduino LED shields (14x9 pixels) but that plan was scrapped due to the very low resolution.

The key focus of this project was to accomplish this vision with certain -- partially arbitrary -- constraints and to get the whole thing done while touching on many aspects of FPGA and electronics development. It is by no means perfect, but it is done while hitting all the project's goals I set for myself.

Project Goal

The main goal of this project was to get my hands dirty with all parts of FPGA development. While the main focus is on the actual hardware description, a good amount of time was also spent on developing the software and electronics side of things to get the full picture.

Besides getting this project actually done, there were a lot of topics I wanted to cover (which includes, but is not limited to):

  • Develop a full FPGA project with everything necessary
  • Keep it flexible that it could run on different devices without too much additional effort
  • Write HDL and verify with testbenches
  • Write packages and make them accessible
  • Make use of existing IP
  • Prototyping
  • Schematics, Layouting and Manufacturing a PCB
  • Interface with other onboard components such as the flash memory
  • Interface with prebuilt offboard components such as the Digilent I2S2 PMOD
  • Interface with external offboard components such as the LED board
  • Work within the limits of the given board such as the Digilent Basys3 (Artix7-35T)
    • 4MB Flash (only ~2MB with configuration)
    • Available IO
    • Clock Speed to maintain realtime
  • Software development
    • Codec for audio and video
  • Miscellaneous
    • Organization of project structure and repository for Git
    • Documentation of the whole project

Please note that these constraints emerged from the components and devices I have at disposal. This project could be done with greater resolution and sound output but the goal is to bring it up and learn everything along the way, that's the reason behind this approach.

Top Level Overview

Here's a top level view of the system. It is build in a modular fashion encapsulating functionality such that everything remains as local as possible so each module is easy to understand. Dataflow is indicated by the directional arrows.

The Control Unit requests data from the memory driver which (here) accesses the onboard SPI flash. It then alternately fills the Audio and Video FIFO which are read by the respective modules on the other side. Those decode the data and fill up a FIFO for Audio and BRAMs for Video. After the data is available the i2s Master and Board Driver will read the data at the correct time and play them back by driving a Digilent i2s2 PMOD and a self designed LED multiplex display.

Documentation

A technical overview as well as project notes and decision making can be found in the documentation. Find the documentation overview here.

Parts

774
QtyValueFootprintReferences
768LEDLED_THT:LED_D5.0mmD1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112 +752
4~MountingHole:MountingHole_3mmH1, H2, H3, H4
1Anodes HeaderConnector_PinHeader_2.54mm:PinHeader_1x24_P2.54mm_VerticalJ1
1Cathodes HeaderConnector_PinHeader_2.54mm:PinHeader_1x32_P2.54mm_VerticalJ2

More from alpyen/fpga-mediaplayer

3
  • 2 layers163.5 × 127.5 mmDriver, the printed circuit board in 3D

    Driver

    alpyen/fpga-mediaplayer

    HDL, Hardware & Software Development project to playback a video with sound and learn while doing so.

    131 parts2
  • 2 layers132 × 102.9 mmSmall led board v1, the printed circuit board in 3D

    Small led board v1

    alpyen/fpga-mediaplayer

    HDL, Hardware & Software Development project to playback a video with sound and learn while doing so.

    107 parts2
  • 2 layers110 × 80 mmSmall led board v2, the printed circuit board in 3D

    Small led board v2

    alpyen/fpga-mediaplayer

    HDL, Hardware & Software Development project to playback a video with sound and learn while doing so.

    89 parts2

Similar boards

  • 2 layers190 × 164 mmRotary encoder with easyC panel, the printed circuit board in 3D

    Rotary encoder with easyC panel

    SolderedElectronics/Rotary-encoder-board-qwiic-hardware-design

    Hardware design, BOM, gerbers and 3D files for Rotary-encoder-board-qwiic designed by Soldered Electronics.

    772 parts
  • 2 layers62 × 78.5 mmBno08x i2c board v3-square panel, the printed circuit board in 3D

    Bno08x i2c board v3-square panel

    tgodfrey0/BNO08x-I2C-PCBs

    This repository contains W.I.P. code and hardware designed for a 9DOF sensor module using a BNO085.

    772 parts1
  • 2 layers77 × 119 mmPanel, the printed circuit board in 3D

    Panel

    TrojanPinata/Pico

    A Raspberry Pi Pico clone with some quality of life features

    776 partsGPL-3.0
  • 2 layers100 × 100 mmMgh80 proto, the printed circuit board in 3D

    Mgh80 proto

    Kris-Sekula/mgh80

    Simple 5 IC Z80 singe-board computer

    769 parts34
  • 2 layers121.5 × 83 mmNeopixel nano - 384 well, the printed circuit board in 3D

    Neopixel nano - 384 well

    pierrebaillargeon/Microplate-Assistive-Pipetting-Light-Emitter

    Microplate Assistive Pipetting Light Emitter (M.A.P.L.E.)

    780 parts17GPL-3.0
  • 2 layers218.2 × 205.3 mmPanel, the printed circuit board in 3D

    Panel

    simonyiszk/SEM-karifa-2023

    780 parts3
  • 2 layers94.2 × 87.9 mmSot-23-panelized, the printed circuit board in 3D

    Sot-23-panelized

    kimballa/breakout-boards

    Panelized breakout boards for SOIC, TSSOP, SOT-23, and more...

    780 parts1

Questions

How big is the Display PCB?

It measures 233.5 × 181.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Display use?

774 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Display KiCad files?

From the alpyen/fpga-mediaplayer repository on GitHub, at the commit this page was made from: the board is kicad/fullsize_led_board/display/display.kicad_pcb and its schematic kicad/fullsize_led_board/display/display.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Display design in my own project?

Its repository states no licence, so its author keeps all rights: ask alpyen before reusing the design.