2 layers21 × 51 mm
2 layers77 × 119 mm
Panel
TrojanPinata/PicoA Raspberry Pi Pico clone with some quality of life features
- Size
- 77 × 119 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 776
- Nets
- 378
- Pads
- 2,144
- Tracks, vias
- 3,864, 300
- Pours
- 24
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 9 May 2024
- Updated
- 28 Aug 2024
Overview
Panel is an open-source printed circuit board by TrojanPinata, from the TrojanPinata/Pico repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 77 × 119 mm with 776 parts on 378 nets, routed with 3,864 tracks and 300 vias.
It is built around the RP2040, W25Q16JVUXIQ and TLV75533PDBVR-MS, with the 0805L050WR and 1N4002W among its other parts. Its parts include 108 capacitors, 84 resistors, 24 connectors, 18 ICs and 12 diodes. It belongs with the RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q16JVUXIQ
USON-8-EP(2x3)-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI USON-8-EP(2x3) NOR FLASH ROHSWinbond ElecNOR FLASH
TLV75533PDBVR-MS
SOT-23-5SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIUncategorised
0805L050WR
0805-40℃~+85℃ 1.25mm 1.5mm 100A 100ms 150mΩ 1A 2.2mm 500mA 500mW 6V 850mΩ 0805 Resettable Fuses ROHSLittelfuseResettable Fuses
1N4002W
SOD-123FLDiodes - General Purposehongjiacheng
README
README.mdPico
This project is a precursor to a future project which I aim to use a RP2040 as the microcontroller as the core of a keyboard, very similar to my original keyboard but with PCBA.
The goal of this was to prove the feasability of using PCBA as well as prove my ability to make a functioning RP2040 microcontroller board. The Pi Pico was simply chosen as it was a very accessible option.
If you want to use this project, it should be noted that this is open source, but I would rather you simply use this as a reference. Putting that much confidence in someone elses work is dangerous, and I cannot guarantee spec with the original.
The only major changes with these boards vs the real deal are the addition of a reset button and usb-c header (something that should be on the original :| )
Parts
776| Qty | Value | Footprint | References |
|---|---|---|---|
| 464 | NPTH | NPTH | KiKit_MB_10_1, KiKit_MB_10_2, KiKit_MB_10_3, KiKit_MB_10_4, KiKit_MB_10_5, KiKit_MB_10_6, KiKit_MB_10_7, KiKit_MB_10_8, KiKit_MB_11_1, KiKit_MB_11_2, KiKit_MB_11_3, KiKit_MB_11_4, KiKit_MB_11_5, KiKit_MB_11_6, KiKit_MB_11_7, KiKit_MB_11_8 +448 |
| 66 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C1, C1, C1, C1, C1, C10, C10, C10, C10, C10, C10, C16, C16, C16, C16 +50 |
| 18 | 10k | Resistor_SMD:R_0402_1005Metric | R9, R9, R9, R9, R10, R10, R10, R10, R10, R10, R14, R14, R14, R14, R14, R14 +2 |
| 18 | LOGO | LOGO | G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G*** +2 |
| 18 | TestPoint | libraries:CustomTestPoint | TP1, TP1, TP1, TP1, TP1, TP1, TP2, TP2, TP2, TP2, TP2, TP2, TP3, TP3, TP3, TP3 +2 |
| 12 | 10uF | Capacitor_SMD:C_0402_1005Metric | C13, C13, C13, C13, C13, C13, C19, C19, C19, C19, C19, C19 |
| 12 | 1k | Resistor_SMD:R_0402_1005Metric | R7, R7, R7, R7, R7, R7, R8, R8, R8, R8, R8, R8 |
| 12 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C11, C11, C11, C11, C11, C11, C12, C12, C12, C12, C12, C12 |
| 12 | 22pF | Capacitor_SMD:C_0402_1005Metric | C14, C14, C14, C14, C14, C14, C15, C15, C15, C15, C15, C15 |
| 12 | 27 | Resistor_SMD:R_0402_1005Metric | R1, R1, R1, R1, R1, R1, R2, R2, R2, R2, R2, R2 |
| 12 | 5.1k | Resistor_SMD:R_0402_1005Metric | R11, R11, R11, R11, R11, R11, R12, R12, R12, R12, R12, R12 |
| 6 | 0805L050WR | Fuse:Fuse_0805_2012Metric | F1, F1, F1, F1, F1, F1 |
| 6 | 1 | Resistor_SMD:R_0402_1005Metric | R4, R4, R4, R4, R4, R4 |
| 6 | 100k | Resistor_SMD:R_0402_1005Metric | R15, R15, R15, R15, R15, R15 |
| 6 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y1, Y1, Y1, Y1, Y1 |
| 6 | 1N4002W | Diode_SMD:D_SOD-123 | D3, D3, D3, D3, D3, D3 |
| 6 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C3, C3, C3, C3, C3 |
| 6 | 200 | Resistor_SMD:R_0402_1005Metric | R3, R3, R3, R3, R3, R3 |
| 6 | 470 | Resistor_SMD:R_0402_1005Metric | R5, R5, R5, R5, R5, R5 |
| 6 | 5.6k | Resistor_SMD:R_0402_1005Metric | R13, R13, R13, R13, R13, R13 |
| 6 | BOOT_SEL | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW2, SW2, SW2, SW2, SW2, SW2 |
| 6 | BOTTOM_PINS | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3, J3, J3, J3, J3, J3 |
| 6 | FB | Resistor_SMD:R_0402_1005Metric | FB1, FB1, FB1, FB1, FB1, FB1 |
| 6 | LED | LED_SMD:LED_0402_1005Metric | D1, D1, D1, D1, D1, D1 |
| 6 | LEFT_PINS | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J1, J1, J1, J1, J1, J1 |
| 6 | RESET | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW1, SW1, SW1, SW1, SW1 |
| 6 | RIGHT_PINS | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J2, J2, J2, J2, J2, J2 |
| 6 | RP2040 | RP2040_minimal:RP2040-QFN-56 | U1, U1, U1, U1, U1, U1 |
| 6 | TLV75533PDBVR | Package_TO_SOT_SMD:SOT-23-5 | U3, U3, U3, U3, U3, U3 |
| 6 | USB_C_Receptacle_USB2.0 | HRO-TYPE-C31-M-12:HRO-TYPE-C-31-M-12 | J4, J4, J4, J4, J4, J4 |
| 6 | W25Q16JVUXIQ | Package_SON:SON-8-1EP_3x2mm_P0.5mm_EP1.4x1.6mm | U2, U2, U2, U2, U2, U2 |
More from TrojanPinata/Pico
1Similar boards
- 2 layers82 × 144.9 mm
- 2 layers21 × 51.3 mm
PicoBoot
RetroScaler/RP2040-PICO-BOOT
Raspberry PI RP2040 PICOBOOT for the Game cube console
57 parts33GPL-3.0 - 2 layers90 × 60 mm
N64xCartDumper v2.1
Auroxin/N64xCart-Dumper
an open hardware / firmware project for dumping Nintendo 64 cartridges as a USB mass storage device
53 parts7 - 2 layers252.9 × 110.6 mm
- 2 layers21.5 × 51.3 mm
- 2 layers349 × 141 mm
Panel
TrojanPinata/Model-B
A 75% keyboard based on the RP2040 - with hotswappable switches, OLED display and rotary encoder
392 parts3 - 2 layers21 × 51 mm
Envious Data EnvOpenPico EnvOpenPico RP2040
punkfab/pcb-corpus
235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark
58 parts1 - 2 layers139.5 × 92 mm
Questions
How big is the Panel PCB?
It measures 77 × 119 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Panel use?
776 parts, built around the RP2040, W25Q16JVUXIQ, TLV75533PDBVR-MS and 0805L050WR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panel KiCad files?
From the TrojanPinata/Pico repository on GitHub, at the commit this page was made from: the board is pico/panel/panel.kicad_pcb and its schematic pico/panel/panel.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panel design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).