Skip to the content
2 layers95 × 95 mmMain pcb, the printed circuit board in 3D

Moduar LED light painting strip with 180 LEDs per meter

Size
95 × 95 mm
Copper layers
2
Thickness
1.6 mm
Parts
52
Nets
84
Pads
228
Tracks, vias
538, 91
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
27 Jun 2021
Updated
1 Jun 2024

Overview

Main pcb is an open-source printed circuit board by akaFunk, from the akaFunk/BlinkyBar repository on GitHub, published under the CC-BY-4.0 licence. It is a 2-layer board of 95 × 95 mm with 52 parts on 84 nets, routed with 538 tracks and 91 vias.

It is built around the ATMEGA328P-AU, AZ1117CH-5.0TRG1 and SC16IS752IPW, with the RC0603JR-0710KL, CC0603KRX7R0BB104 and CC0603JRNPO9BN270 among its other parts. Its parts include 15 resistors, 11 capacitors, 9 connectors, 3 ICs and 3 diodes. It belongs with the AVR (ATmega, ATtiny) and Raspberry Pi (Linux) boards of this library.

Main components

12

README

README.md

BlinkyBar

The BlinkyBar is a modular LED light painting device based on the WS2812B programmable RGB LEDs. It features modules with a length of approximately 250mm, which can be attached to a host module of an arbitrary length. The host module holds a Raspberry Pi Zero W, which provides access to the device with a Wifi access point. A website running on the Raspi allows to upload an image. Once the trigger button on the host module is pressed, the image is played back one column after another. Combining this with a long time expose will paint the uploaded image into thin air.

We are currently working on the first release. Images made with an earlier version are shown below. This older version featured only 60 LEDs per meter, while the new one will have 180 LEDs per meter.

Images

Examples of the old version: Example Image 1 Example Image 2

3D rendering of the current main module: Example Image 1 Example Image 1

Images of the first prototype: Example Image 1 Example Image 1 Example Image 1 Example Image 1

Building BlinkyBar

Issues to be aware of

BlinkyBar is still in development and there are currently a few issues, which are important to note if you want to build it. They will be addressed in the future:

  • The 1117 LDO is not working with the currently populated MLCC output capacitors. Their ESR is too low. You will hear an annoying high pitch tone and have a ~400 mVpp triangle on the output voltage. Either replace the output capacitors with Aluminium Electrolytic types, solder a 0.5 Ohm resistor in series with the capacitors, or use a different LDO (for example BL8071CLBTR33 or AP2114H-3.3TRG1). Currently we have tested only using the Aluminium Electrolytic caps which works fine.
  • The modules are not able to power down automatically if the host module powers down. Please make sure to remove the batteries, otherwise they will be empty after some time. However, the battery under-voltage protection should work for both the host and the modules, so your batteries are safe.

Parts

Additional part required for a BlinkyBar with 4 modules and the main unit, i.e., 10 module PCBs and a length of 2475 mm and 450 LEDs. For the PCBs you will find lists in CSV format exported from KiCad in each of the PCBs output folder.

DescriptionCount3D Model
U-Profile, 30x20x2x495 mm (WxHxTxL), Aluminum1main_profile
U-Profile, 30x20x2x495 mm (WxHxTxL), Aluminum4module_profile
6x6x100 mm, Steel8module_bolt
3D-printed stand for the module PCB15module_stand
3D-printed power button protector1main_button_protector
3D-printed main case1main_case
3D-printed handle1main_handle
18650 Holder1218650_holder
Plate, 35x25x3 mm, Steel4module_plate
Main PCB holding the Raspberry Pi Zero and the user interface PCB1main_pcb
Main PCB adapter to combine and raise the two connector fro the module pcb within the main module1main_pcb_adapter
Main PCB front panel as the case cover1main_pcb_front
Main PCB user interface holding a few buttons and an LED1main_pcb_ui
Module PCB with the LEDs10module_pcb
M4x12 wing screw (DIN 316)4
M3x5 flat head screw (ISO7380) to hold the case to the profile2
M3x4 countersunk head screw (ISO 14581) to hold the battery holders24
M3 nut (ISO 4032) to hold the battery holders in the main case4
M3x8 flat head screw (ISO7380) to hold the main PCB in the case4
M3 nut (ISO 4032) to hold the main PCB in the case4
M3x20 flat head screw (ISO7380) to hold the front panel PCB to the case4
M3 nut (ISO 4032) to hold the front panel PCB to the case4
M3x12 flat head screw (ISO7380) to hold the stand to the profile28
M3x20 flat head screw (ISO7380) to hold the handle and two of the stands to the profile2
M3 nut (ISO 4032) to hold the stand to the profile30
M3x8 flat head screw (ISO7380) to hold the module PCB to the stand60
M3 nut (ISO 4032) to hold the module PCB to the stand60
M2x5 flat head screw (ISO7380) to hold the power button protector to the front panel PCB2
M2 nut (ISO 4032) to hold the power button protector to the front panel PCB2
M3x8 flat head screw (ISO7380) to hold the steel bolts to the profile16

Replacement parts

Some MPN in the CSV/schematics are just some random ones, for example for pin headers, which fit and were available at the time of design. Those may be replaced with similar types. A (bar far not complete) list of such parts is given below:

PartDescriptionReplacements

TODO/Further development

  • Make everything much simpler, especially the bus topology, mechanical design, and power design
  • Use smaller LEDs, for example SK6805-EC15, and increase LED density

Parts

52
QtyValueFootprintReferences
610kResistor_SMD:R_0603_1608MetricR3, R4, R6, R9, R11, R18
5100nCapacitor_SMD:C_0603_1608MetricC1, C2, C6, C7, C8
427pCapacitor_SMD:C_0603_1608MetricC3, C4, C12, C13
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_PadH1, H2, H3, H4
4UIConnector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_VerticalJ2, J3, J5, J6
31kResistor_SMD:R_0603_1608MetricR2, R12, R13
3330Resistor_SMD:R_0603_1608MetricR1, R7, R8
233Resistor_SMD:R_0603_1608MetricR14, R15
2D_SchottkyDiode_SMD:D_SOD-123D2, D4
110uCapacitor_SMD:C_1206_3216MetricC14
116 MHzCrystal:Crystal_SMD_HC49-SDY1
122uCapacitor_SMD:C_1206_3216MetricC15
12x18650Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_VerticalBT1
168kResistor_SMD:R_0603_1608MetricR10
18MHzCrystal:Crystal_SMD_HC49-SDY2
1ATmega328P-AUPackage_QFP:TQFP-32_7x7mm_P0.8mmU3
1AZ1117-50Package_TO_SOT_SMD:SOT-223-3_TabPin2U4
1BSS123Package_TO_SOT_SMD:SOT-23Q1
1BTN_TRIGConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ9
1DBGConnector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_VerticalJ1
1HSS2307Package_TO_SOT_SMD:SOT-23WQ2
1ISPConnector_IDC:IDC-Header_2x03_P2.54mm_VerticalJ8
1LEDLED_SMD:LED_0603_1608MetricD1
1PolyfuseFuse:Fuse_1812_4532Metric_CastellatedF1
1Raspberry_Pi_Zero_WHmain_pcb:RPiZeroJ4
1SC16IS752IPWPackage_SO:TSSOP-28_4.4x9.7mm_P0.65mmU1
1SW_SPSTButton_Switch_THT:SW_PUSH_6mm_H8mmSW1
1UPDNConnector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_VerticalJ7

More from akaFunk/BlinkyBar

3
  • 2 layers247.5 × 25 mmModule pcb, the printed circuit board in 3D

    Module pcb

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    106 parts1CC-BY-4.0
  • 2 layers74 × 39 mmMain pcb ui, the printed circuit board in 3D

    Main pcb ui

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    17 parts1CC-BY-4.0
  • 2 layers20 × 25 mmMain pcb adapter, the printed circuit board in 3D

    Main pcb adapter

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    3 parts1CC-BY-4.0

Similar boards

  • 2 layers65 × 30 mmEDice, the printed circuit board in 3D

    EDice

    akaFunk/EDice

    A very cheap electronic dice used for soldering exercises

    24 parts
  • 2 layers52.8 × 55 mmILDAWaveX16, the printed circuit board in 3D

    ILDAWaveX16

    stanleyondrus/ILDAWaveX16

    ILDAWaveX16 is an open-source, high-resolution, wireless laser DAC with SD-card playback, network control, and ILDA output.

    95 parts42
  • 2 layers116.2 × 95.4 mmMacropad, the printed circuit board in 3D

    Macropad

    sarthakmmishra/macropad

    STM32F103C8T6 based macropad

    99 parts1
  • 2 layers79 × 100 mmBREAD slice v2, the printed circuit board in 3D

    BREAD slice v2

    ikmitche/OSHE-RecycleBot

    The Home of the Open Source Hardware Enterprise's RecycleBot Project

    36 parts
  • 4 layers70 × 70 mmBlue interface board, the printed circuit board in 3D

    Blue interface board

    BetzDrive/interface-board

    Power and signal conditioning board for the Betz Drive system

    130 parts5
  • 2 layers229.6 × 158.2 mmSpace banana, the printed circuit board in 3D

    Space banana

    obra/space-banana

    https://twitter.com/erinbeess/status/1503424797224677376?s=20&t=_vethJano1TXJZ3IsSkWwQ

    129 parts2
  • 4 layers152.1 × 80.1 mmChicker, the printed circuit board in 3D

    Chicker

    sfunderbots/Electrical

    PCB etc.

    195 parts

Questions

How big is the Main pcb PCB?

It measures 95 × 95 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Main pcb use?

52 parts, built around the ATMEGA328P-AU, AZ1117CH-5.0TRG1, SC16IS752IPW and RC0603JR-0710KL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Main pcb KiCad files?

From the akaFunk/BlinkyBar repository on GitHub, at the commit this page was made from: the board is main_pcb/main_pcb.kicad_pcb and its schematic main_pcb/main_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Main pcb design in my own project?

Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).