Skip to the content
2 layers34.3 × 30 mmEspdisplay, the printed circuit board in 3D

ESP-WROOM-32 breakout board to connect it to a Waveshare E-Ink display

Size
34.3 × 30 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
37
Pads
65
Tracks, vias
67, 7
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
11 Apr 2018
Updated
27 Apr 2018

Overview

Espdisplay is an open-source printed circuit board by ahinrichs, from the ahinrichs/DoorsignEPD-pcb repository on GitHub. It is a 2-layer board of 34.3 × 30 mm with 11 parts on 37 nets, routed with 67 tracks and 7 vias.

It is built around the ESP-WROOM-32D. Its parts include 5 connectors, 2 resistors, 2 switches and 1 IC. It belongs with the lEDs and displays and home automation and IoT boards and the ESP32 boards of this library.

Main components

1

README

README.md

DoorsignEPD-pcb

ESP-WROOM-32 breakout board to connect it to a Waveshare E-Ink display.

PCB

Inspired by article Ausdauernde Infotafel from German computer magazine c't. Example arduino and server software can be found here.

Input voltage is connected to a voltage regulator jack and directly to Pin6/IO34/ADC6 for monitoring. Hence input voltage must be below 3.6V. I use 2xAA together with a step up regulator. Additionally I connected a pad for Pin8/IO32/ADC4/TOUCH9. Haven't used it yet. Maybe for a touch wakeup or status LED.

Display connector pin assignment is identical to the Waveshare hat connector.

Rev A2 PCB can be ordered e.g. via aisler.net: https://aisler.net/p/HSIWEKKI

Components needed in addition to PCB:

  • Of course an ESP-WROOM-32 (or footprint compatible)
  • Waveshare E-Ink display
  • 3.3V voltage regulator or other 3.3V source
  • Battery + holder of your choice
  • 2x ~10kΩ pullup resistors R1+R2
  • 2x tactile switch (included in aisler precious parts)
  • 1x JST-PH 8 connector header+housing (included in aisler precious parts)
  • 1x JST-PH 2 connector header+housing (included in aisler precious parts)
  • 10-15 JST-PH terminals (included in aisler precious parts)
  • Crimp tool for JST-PH connectors
  • 3.3V capable USB-TTL adapter for programming

Programming

This a minimalistic board to save power. No USB included. So you need an USB-TTL adapter that is capable of doing 3.3V. This one works for me under Linux.

To upload an arduino sketch/flash firmware:

  1. Connect the USB-Adapter GND/RX/TX to the board. Most adapters need RX board/TX adapter and TX board/RX adapter. If that doesn't work try RX/RX+TX/TX. To check press the Reset button. The serial monitor must show the ESP33 boot log.
  2. Press and hold the Boot(loader) button, shortly press the Reset button, then release the Boot button. Log should show the ESP32 entering bootloader mode.
  3. Now stop any serial monitor (Arduino IDE does this automatically)
  4. Upload the sketch and wait until completion
  5. Again press the Reset button
  6. Restart serial monitor (Arduino IDE does this automatically)

Assembled board

Assembled

Changelog

Rev A2 (minor)
  • Trace width power supply + GND
  • Via min size 0.65mm (=drill + 0.25mm)
Rev A1
  • Initial revision

Parts

11
QtyValueFootprintReferences
210kespdisplay:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2
1BOOTespdisplay:SW_Tactile_SPST_NO_6mmx3.5mmSW2
1DOutespdisplay:JST_PH_S8B-PH-K_08x2.00mm_AngledJ3
1ESP-WROOM-32espdisplay:ESP-WROOM-32U1
1IO32espdisplay:Pin_Header_Straight_1x01_Pitch2.54mmJ5
1PWRespdisplay:JST_PH_S2B-PH-K_02x2.00mm_AngledJ1
1RESETespdisplay:SW_Tactile_SPST_NO_6mmx3.5mmSW1
1Serialespdisplay:Pin_Header_Straight_1x03_Pitch2.54mmJ4
1URegespdisplay:Pin_UReg_1x04_Pitch2.54mmJ2

The 10 most common of 11 parts.

Similar boards

  • 2 layers127 × 114.3 mmNes, the printed circuit board in 3D

    Nes

    dkonigsberg/nestronic

    Nestronic Game Music Synthesizer Alarm Clock

    144 parts38
  • 2 layers90 × 40 mmEsp32-tlk110, the printed circuit board in 3D

    Esp32-tlk110

    kazkojima/esp32-phy

    KiCAD files and apps for ESP-WROOM-32 ethernet boards

    57 parts34GPL-3.0
  • 2 layers93 × 60 mmHornbill Open Universal Remote, the printed circuit board in 3D

    Hornbill Open Universal Remote

    ExploreEmbedded/hornbill-our

    Open Univeral Remote with Hornbill ESP32 dev tools. BLE IR Bridge for device control

    75 parts27
  • 2 layers36.2 × 39.2 mmOpenmv daughter2, the printed circuit board in 3D

    Openmv daughter2

    kazkojima/pmlps

    Tiny local positioning system with OpenMV cam

    19 parts18GPL-3.0
  • 2 layers93 × 60 mmHornbill lights, the printed circuit board in 3D

    Hornbill lights

    ExploreEmbedded/hornbill-lights

    Firmware and App for controlling RGB LED lights with the Hornbill ESP32 Platform

    54 parts16
  • 6 layers131 × 80 mmOpenHardwareHolterMonitor, the printed circuit board in 3D

    OpenHardwareHolterMonitor

    OpenElectronicsLab/OpenHardwareHolterMonitor

    OpenHardware ECG Holter Monitor

    165 parts9GPL-3.0

Questions

How big is the Espdisplay PCB?

It measures 34.3 × 30 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Espdisplay use?

11 parts, built around the ESP-WROOM-32D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Espdisplay KiCad files?

From the ahinrichs/DoorsignEPD-pcb repository on GitHub, at the commit this page was made from: the board is espdisplay.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Espdisplay design in my own project?

Its repository states no licence, so its author keeps all rights: ask ahinrichs before reusing the design.