
EnvMonitor
kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程

Este proyecto consiste en el diseño y construcción de un robot móvil capaz de resolver laberintos físicos con paredes de manera autónoma.
Robot2 is an open-source printed circuit board by agumurray, from the agumurray/G8-TP1 repository on GitHub. It is a 2-layer board of 137 × 85.5 mm with 32 parts on 81 nets, routed with 94 tracks and 0 vias.
It is built around the HC-SR04.
Robot resolutor de laberintos con EDU-CIAA
Este proyecto consiste en el diseño y construcción de un robot móvil capaz de resolver laberintos físicos con paredes de manera autónoma. El sistema utiliza como controlador principal la EDU-CIAA, que gestiona los sensores y motores, y ejecuta algoritmos de navegación para alcanzar la salida sin necesidad de un mapa previo.
Exploración autónoma de laberintos físicos.
Algoritmos de resolución basados en estrategias clásicas (wall-following, Pledge, Trémaux).
Plataforma móvil con dos motores DC controlados mediante un puente H L298N.
Sensores ultrasónicos para la detección de paredes y obstáculos.
Posibilidad de extender funcionalidades con:
Hardware:
Software:
General: Desarrollar un robot controlado por EDU-CIAA capaz de explorar físicamente un laberinto con paredes y alcanzar la salida mediante estrategias de navegación autónoma.
Primarios:
Secundarios:
Este proyecto fue desarrollado por el Grupo 8 en el marco de la materia Taller de Proyecto I en la Facultad de Ingeniería de la UNLP:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | , , , , , , , , , , , , , , , | ||
| 3 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | RES 10K, RES 10K, RES 10K |
| 3 | 20K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R5, RES 20K |
| 3 | HC-SR04 | Libreria_EDU_CIAA_NXP:HC-SR04 | HC-SR04-1, HC-SR04-2, HC-SR04-3 |
| 2 | Conn_02x20_Odd_Even | Libreria_EDU_CIAA_NXP:PIN_ARRAY_20X2 | CIAA-P1-1, CIAA-P2-1 |
The 27 most common of 32 parts.

kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程


NikolaiRadke/Noko_2
The do-it-yourself Arduino-based Noko monster. Version 2 with PCB and 3D printed casing.

billtsol/Maze
This project demonstrates how to use an Arduino board, IR sensors, and a motor driver shield to create a maze-solving robot.

c-lydia/ESP-ROS2
A tiny robot with IMU (MPU5060) and an ultrasonic sensor (HC-SR04), running on micro-ROS, communicating over UDP.

dbrgn/crazyflie2-hcsr04
Ultrasonic sensor (HC-SR04) extension board for the Crazyflie 2.0

YousefAliAicha/aegis-embedded-system
Networked rotating ultrasonic radar system built on the Deneyap Kart 1A (ESP32-S3), with a real-time web dashboard served directly from the board.

YousefAliAicha/sentinel-arduino-firmware
Adaptive traffic-light FSM on the Arduino UNO R3 — pedestrian preemption, LDR-gated night mode with HC-SR04 vehicle detection, and a multiplexed 7-segment countdown. Fully non-blocking.
It measures 137 × 85.5 mm and has 2 copper layers, 1.6 mm thick.
32 parts, built around the HC-SR04. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the agumurray/G8-TP1 repository on GitHub, at the commit this page was made from: the board is schematics/robot2.kicad_pcb and its schematic schematics/robot2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask agumurray before reusing the design.