Skip to the content
2 layers28 × 11 mmTemperature Sensor I2C, the printed circuit board in 3D

Small TMP117 temperature-sensor board for the custom Radxa CM5 camera carrier. The intended use is remote temperature monitoring, including the camera FPGA area.

Size
28 × 11 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
7
Pads
25
Tracks, vias
55, 3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
26 Oct 2026
Updated
26 Oct 2026

Overview

Temperature Sensor I2C is an open-source printed circuit board by ABlairJamieson, from the ABlairJamieson/Temperature_Sensor_I2C repository on GitHub. It is a 2-layer board of 28 × 11 mm with 10 parts on 7 nets, routed with 55 tracks and 3 vias.

It is built around the TMP117AIDRVR. Its parts include 4 resistors, 2 capacitors, 1 IC and 1 connector. It belongs with the sensors and measurement boards of this library.

Main components

1

README

README.md

I2C Temperature Sensor Board

Small TMP117 temperature-sensor board for the custom Radxa CM5 camera carrier. The intended use is remote temperature monitoring, including the camera FPGA area. Two boards can connect using separate cables to the carrier's two parallel I2C connectors, provided each sensor has a different address.

KiCad project

Open Temperature Sensor I2C.kicad_pro in KiCad 10.

  • Temperature Sensor I2C.kicad_sch: schematic.
  • Temperature Sensor I2C.kicad_pcb: routed PCB.
  • includes/TMP117AIDRVR/: custom symbol, footprint and STEP model.
  • sym-lib-table and fp-lib-table: project-relative library definitions.

Local history, automatic backups, editor preferences and generated jlcpcb/ outputs are excluded from Git. Regenerate manufacturing outputs from the intended design revision before ordering.

Power and connector

Use 3.3 V power and 3.3 V I2C signals with the matching carrier. Do not connect this board to the camera's 12 V supply.

J1 is a four-pin JST-PH, 2.00 mm pitch, vertical header (B4B-PH-K footprint):

PinSignal
1+3V3
2I2C SDA
3I2C SCL
4GND

Verify cable continuity by pin number: 1-to-1, 2-to-2, 3-to-3, 4-to-4. Do not rely solely on wire colours or the apparent connector orientation. Disconnect power before connecting or changing cables.

There are no SDA/SCL pull-up resistors on this sensor board; the matching CM5 carrier supplies them. For another host, provide suitable pull-ups to 3.3 V. Keep cables short and start testing at 100 kHz.

I2C address selection

Fit exactly one of the four zero-ohm address resistors. Leave all others unpopulated (DNP). Fitting more than one can short supply or bus signals.

Fit onlyADD0 connection7-bit address
R3GND0x48
R4+3V30x49
R1SDA0x4A
R2SCL0x4B

The saved schematic populates R3 only, selecting 0x48. For two sensors, assemble one with R3 only and the other with R4 only. These addresses do not overlap the carrier's INA226 monitors (0x40, 0x41). Check the assembly BOM/DNP settings for each sensor variant before ordering.

Assembly and mounting

  • U1: TMP117AIDRVR, WSON package.
  • C1: 10 uF supply capacitor; C2: 100 nF supply bypass.
  • ALERT is unused; the exposed thermal pad is electrically unconnected.
  • The thermal pad should remain unsoldered for best accuracy on a rigid PCB, as recommended by TI. Preserve the footprint's intentional lack of a centre-pad paste opening.
  • Ensure components do not obstruct the intended thermal-contact surface. Use electrically insulating thermal interface material where needed; do not allow board copper or connector pins to short the camera electronics.
  • This measures the sensor's temperature. Contact, airflow and mounting affect how closely that represents the FPGA/package temperature.

Initial check

  1. Verify the fitted address resistor and cable pinout with power disconnected.
  2. Connect to the carrier and confirm 3.3 V between J1 pins 1 and 4.
  3. Enable the appropriate I2C controller/pinmux on the CM5. Determine the actual Linux bus using i2cdetect -l; do not assume a fixed bus number.
  4. Confirm communication at the selected address and read temperature using a TMP117-compatible driver/application. Allow the first conversion to finish.
  5. With two sensors attached, verify both addresses and gently warm one board to establish which software channel corresponds to each physical sensor.

Hardware checks do not replace testing an assembled board and its actual cables.

References

Parts

10
QtyValueFootprintReferences
40Resistor_SMD:R_0603_1608MetricR1, R2, R3, R4
2MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2
10.1uFCapacitor_SMD:C_0402_1005MetricC2
110uFCapacitor_SMD:C_0805_2012MetricC1
1Conn_01x04_PinConnector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalJ1
1TMP117AIDRVRTMP117AIDRVR:SON65P200X200X80-7NU1

Similar boards

  • 4 layers39 × 39 mmOneInchEye, the printed circuit board in 3D

    OneInchEye

    will127534/OneInchEye

    A One Inch CMOS sensor (IMX283) camera board designed for Raspberry Pi

    94 parts355MIT
  • 4 layers39 × 39 mmShutterEye, the printed circuit board in 3D

    ShutterEye

    will127534/ShutterEye

    A simple camera board using SC910GS 1" 4K@30fps global shutter sensor

    157 parts26MIT
  • 4 layers60 × 40 mmFtx, the printed circuit board in 3D

    Ftx

    SETIatHCRO/Front-Page

    Documentation related to the Allen Telescope Array at the Hat Creek Radio Observatory Wiki Link Below

    153 parts5
  • 4 layers44.5 × 50.6 mmKompic Mk1b, the printed circuit board in 3D

    Kompic Mk1b

    porupski/kompic-wearable

    Compact Open Multi-sensor Platform & Apparat.

    149 parts3GPL-3.0
  • 2 layers56 × 6.2 mmRing pcb, the printed circuit board in 3D

    Ring pcb

    dezash123/ring-pcb

    60 parts2
  • 2 layers228.9 × 5.5 mmTMP117 section 5cm, the printed circuit board in 3D

    TMP117 section 5cm

    BerkeleyLab/DxP-sensor-probes

    Hardware design for the DxP (Distributed sensor Profiling) sensor probe.

    38 parts1
  • 4 layers62.9 × 42.5 mmPCB Design PFE, the printed circuit board in 3D

    PCB Design PFE

    khawlahhouki/fatigue-detection-edge-ai

    Real-time physical fatigue detection using Edge AI on STM32H7 with FreeRTOS, biosignal acquisition (PPG, EMG, IMU) and TFLite INT8 inference

    64 parts1

Questions

How big is the Temperature Sensor I2C PCB?

It measures 28 × 11 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Temperature Sensor I2C use?

10 parts, built around the TMP117AIDRVR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Temperature Sensor I2C KiCad files?

From the ABlairJamieson/Temperature_Sensor_I2C repository on GitHub, at the commit this page was made from: the board is Temperature Sensor I2C.kicad_pcb and its schematic Temperature Sensor I2C.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Temperature Sensor I2C design in my own project?

Its repository states no licence, so its author keeps all rights: ask ABlairJamieson before reusing the design.