
EnvMonitor
kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程

Contributions for the TARS system
HC SR04sensor is an open-source printed circuit board by Aaronc0d3, from the Aaronc0d3/Senior-Design-Project repository on GitHub. It is a 2-layer board of 48 × 96.5 mm with 11 parts on 9 nets, routed with 25 tracks and 0 vias.
It is built around the HC-SR04. Its parts include 4 resistors, 4 connectors, 2 diodes and 1 IC.
This is files containg my PCB design, which holds an HC-SR04 Ultrasonic Sensor, a red and green led, male GPIO ports, and some resistors
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1000R | Symbol:Resistor_holes | R1, R2, R3 |
| 3 | Conn_01x01_Socket | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J1, J3, J4 |
| 2 | LED | LED_THT:LED_D3.0mm_Horizontal_O6.35mm_Z10.0mm | D1, D2 |
| 1 | 2000R | Symbol:Resistor_holes | R5 |
| 1 | Conn_01x03_Socket | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | HC-SR04 | custom:XCVR_HC-SR04 | U1 |

kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程


NikolaiRadke/Noko_2
The do-it-yourself Arduino-based Noko monster. Version 2 with PCB and 3D printed casing.

billtsol/Maze
This project demonstrates how to use an Arduino board, IR sensors, and a motor driver shield to create a maze-solving robot.

c-lydia/ESP-ROS2
A tiny robot with IMU (MPU5060) and an ultrasonic sensor (HC-SR04), running on micro-ROS, communicating over UDP.

dbrgn/crazyflie2-hcsr04
Ultrasonic sensor (HC-SR04) extension board for the Crazyflie 2.0

YousefAliAicha/aegis-embedded-system
Networked rotating ultrasonic radar system built on the Deneyap Kart 1A (ESP32-S3), with a real-time web dashboard served directly from the board.

YousefAliAicha/sentinel-arduino-firmware
Adaptive traffic-light FSM on the Arduino UNO R3 — pedestrian preemption, LDR-gated night mode with HC-SR04 vehicle detection, and a multiplexed 7-segment countdown. Fully non-blocking.
It measures 48 × 96.5 mm and has 2 copper layers, 1.6 mm thick.
11 parts, built around the HC-SR04. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Aaronc0d3/Senior-Design-Project repository on GitHub, at the commit this page was made from: the board is PCB-design/HC-SR04sensor.kicad_pcb and its schematic PCB-design/HC-SR04sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Aaronc0d3 before reusing the design.