
Langpie
langpie/langpie
An Opensource Raspberry Pi Based Smart Car Project (ORPSC Project) - 树莓派开源智能车项目

a pcb design for the raspberry pi pico, stepper driver, and motor driver
Pico stepper breakout is an open-source printed circuit board by aams86, from the aams86/pico_carrier_stepper repository on GitHub. It is a 2-layer board of 72.2 × 62.9 mm with 29 parts on 68 nets, routed with 79 tracks and 0 vias.
It is built around the DRV8833PWP. Its parts include 19 connectors, 3 capacitors, 2 resistors, 2 ICs and 2 switches. It belongs with the robots and motor control and interfaces and adapters boards and the RP2040 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Conn_01x01_Pin | TestPoint:TestPoint_Keystone_5019_Minature | J2, J15, J16, J17, J18, J19 |
| 3 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5, J6, J7 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | Conn_01x02_Pin | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4, J13 |
| 2 | Conn_01x05_Pin | Connector_JST:JST_XH_B5B-XH-AM_1x05_P2.50mm_Vertical | J8, J9 |
| 2 | Conn_01x06_Pin | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J1, J14 |
| 2 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J3, J12 |
| 2 | Conn_02x20_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical_SMD | J10, J11 |
| 2 | SW_DIP_x01 | Button_Switch_SMD:SW_SPST_TL3305C | SW3, SW5 |
| 1 | .1u | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | DRV8833PWP | Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalVias | U4 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | ~ | Package_SO:SSOP-24_3.9x8.7mm_P0.635mm | U2 |

langpie/langpie
An Opensource Raspberry Pi Based Smart Car Project (ORPSC Project) - 树莓派开源智能车项目

AleksaHeler/OpenHand
Our attempt at a prosthetic hand using STM32 microcontroller with custom PCB and mechanics


shurik179/yozh
Small robot based on Pololu's Zumo chassis but programmable in CircuitPython

KushlaVR/models-heart
Можливості: Керування через WIFI з телефона або ПК 5 незалежних каналів (світлодіоди/сервомотори) 1 Н-міст для підключення мотора (піковий струм до 3А) Вмонтована BMS 1S та контроллер заряду Li-Ion акумулятора з…

opulo-inc/lumenpnp-archive
This repository is a public archive of the LumenPnP Pick and Place (formerly Index) source material from the beginning in mid-2020 until May 2022. The current source can be found at https://github.com/opulo-inc/lumenpnp


wallComputer/PiZumo_Robot
Git Folder to share hardware and software files for PiZumo Robot.
It measures 72.2 × 62.9 mm and has 2 copper layers, 1.6 mm thick.
29 parts, built around the DRV8833PWP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the aams86/pico_carrier_stepper repository on GitHub, at the commit this page was made from: the board is pico_stepper_breakout.kicad_pcb and its schematic pico_stepper_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask aams86 before reusing the design.