

Teensy 4.0 Attempt 2
- Size
- 68 × 45 mm
- Copper layers
- 6
- Thickness
- 1.51 mm
- Parts
- 80
- Nets
- 167
- Pads
- 408
- Tracks, vias
- 1,501, 209
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 3 Apr 2025
- Updated
- 3 Apr 2025
Overview
Teensy 4.0 Attempt 2 is an open-source printed circuit board by Wierdwizard2587, from the Wierdwizard2587/Custom_Teensy_4.0_PCB repository on GitHub. It is a 6-layer board of 68 × 45 mm with 80 parts on 167 nets, routed with 1,501 tracks and 209 vias.
It is built around the MIMXRT1062DVL6A, MKL02Z32VFG4 and W25Q16JVSSIM, with the TLV75733PDRV, BAT54C and DMG2305UX-7 among its other parts. Its parts include 28 capacitors, 24 connectors, 5 resistors, 4 ICs and 4 diodes. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
6MIMXRT1062DVL6A
MAPBGA-1960℃~+95℃@(TJ) 127 12bit 1MB 32 Bit 3V~3.6V 600MHz ARM Cortex-M7 Built-in+External External MAPBGA-196 Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)MKL02Z32VFG4
QFN-16-EP(3x3)-40℃~+105℃ 1.71V~3.6V 12bit 14 32 Bit 32KB 48MHz 4KB ARM Cortex-M0+ Built-in FLASH QFN-16-EP(3x3) Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)W25Q16JVSSIM
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbond ElecNOR FLASHTLV75733PDRV
WSON-6(2x2)-40℃~+125℃@(Tj) 1 1A 25uA 3.3V 425mV@(1A) 45dB@(100kHz) 5.5V 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBAT54C
SOT-231 Pair Common Cathode 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-23 Schottky Diodes ROHSNexperiaSchottky DiodesDMG2305UX-7
SOT-23-55℃~+150℃ 1 P-Channel 1.4W 10.2nC@4.5V 20V 52mΩ@4.5V、100mΩ@2.5V 5A 77pF 808pF 85pF 900mV P-Channel SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETs
Parts
80| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | Conn_01x01_Pin | Guitar_AI_Pedal_Library:1x1 SMD Pad Conn | J5, J6, J7, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21, J22 +2 |
| 11 | 0.22uF | Capacitor_SMD:C_0603_1608Metric | C5, C6, C8, C9, C15, C17, C20, C23, C25, C27, C28 |
| 6 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C10, C14, C18, C22, C24, C26 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C13, C19, C21 |
| 2 | 100K | Resistor_SMD:R_0603_1608Metric | R2, R4 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C7, C16 |
| 2 | 12pF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 20pF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 470R | Resistor_SMD:R_0603_1608Metric | R3, R5 |
| 2 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D1, D2 |
| 2 | Conn_01x14_Pin | Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_Vertical | J2, J3 |
| 2 | Ferrite 120 | Inductor_SMD:L_0402_1005Metric | L1, L2 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3, D4 |
| 1 | 2.2M | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 24MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_TXC_9HT11-2Pin_2.0x1.2mm_HandSoldering | Y2 |
| 1 | 4.7uH | Inductor_SMD:L_Taiyo-Yuden_MD-3030 | L3 |
| 1 | 500mA | Fuse:Fuse_0402_1005Metric | F1 |
| 1 | Conn_01x01_Pin | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | VUSB |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | DMG2305UX-7 | Guitar_AI_Pedal_Library:SOT91P240X110-3N_DMG2305UX-7 | Q1 |
| 1 | MIMXRT1062DVL6A | Guitar_AI_Pedal_Library:BGA196C65P14X14_1000X1000X152N | U2 |
| 1 | MKL02Z32VFG4 | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.9x1.9mm | U3 |
| 1 | SW_SPST | Button_Switch_SMD:SW_SPST_TL3305A | RST |
| 1 | TLV75733PDRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U4 |
| 1 | USB2_N | Guitar_AI_Pedal_Library:1x1 SMD Pad Conn | J25 |
| 1 | USB2_P | Guitar_AI_Pedal_Library:1x1 SMD Pad Conn | J24 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10103594-0001LF_Horizontal | J1 |
| 1 | W25Q16JVSSIM | Guitar_AI_Pedal_Library:SOIC127P790X216-8N | U1 |
The 74 most common of 80 parts.
Similar boards
- 4 layers1,189 × 841 mm

- 2 layers

- 4 layers69.9 × 162.4 mm

- 2 layers176 × 105 mm

Reference Keyboard
famichu/MagLevSwitch_ReferenceKeyboard
The reference keyboard for the MagLev Switch MX
91 parts2MIT - 2 layers61.6 × 53.7 mm

Osborne floppy emulator
khaddra/osborne-floppy-emulator
Floppy disk drive emulator for the Osborne 1. Unfinished.
82 parts2 - 2 layers109.1 × 77.9 mm

- 6 layers87.6 × 53.9 mm

Teensy 4.1 attempt 1
Wierdwizard2587/Custom-Teensy-4.1-PCB-Design
Custom Designed MCU design based upon Teensy 4.1
92 parts9 - 4 layers90.3 × 94.6 mm

Questions
How big is the Teensy 4.0 Attempt 2 PCB?
It measures 68 × 45 mm and has 6 copper layers, 1.51 mm thick.
What parts does the Teensy 4.0 Attempt 2 use?
80 parts, built around the MIMXRT1062DVL6A, MKL02Z32VFG4, W25Q16JVSSIM and TLV75733PDRV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Teensy 4.0 Attempt 2 KiCad files?
From the Wierdwizard2587/Custom_Teensy_4.0_PCB repository on GitHub, at the commit this page was made from: the board is Teensy_4.0_Attempt_2.kicad_pcb and its schematic Teensy_4.0_Attempt_2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Teensy 4.0 Attempt 2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Wierdwizard2587 before reusing the design.