

Teensy 4.1 attempt 1
Custom Designed MCU design based upon Teensy 4.1
- Size
- 87.6 × 53.9 mm
- Copper layers
- 6
- Thickness
- 1.51 mm
- Parts
- 92
- Nets
- 193
- Pads
- 589
- Tracks, vias
- 2,331, 249
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Apr 2025
- Updated
- 30 Jun 2025
Overview
Teensy 4.1 attempt 1 is an open-source printed circuit board by Wierdwizard2587, from the Wierdwizard2587/Custom-Teensy-4.1-PCB-Design repository on GitHub. It is a 6-layer board of 87.6 × 53.9 mm with 92 parts on 193 nets, routed with 2,331 tracks and 249 vias.
It is built around the MIMXRT1062DVJ6B, MKL02Z32VFG4 and DP83825IRMQR, with the W25Q64JVXGIM, MAX1562ESA+ and CC0603KRX7R6BB224 among its other parts. Its parts include 32 capacitors, 18 resistors, 9 connectors, 8 ICs and 6 diodes. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
12MIMXRT1062DVJ6B
LFBGA-196127 12bit 1MB 32 Bit 3V~3.6V 600MHz ARM Cortex-M7 Built-in+External External LFBGA-196 Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)MKL02Z32VFG4
QFN-16-EP(3x3)-40℃~+105℃ 1.71V~3.6V 12bit 14 32 Bit 32KB 48MHz 4KB ARM Cortex-M0+ Built-in FLASH QFN-16-EP(3x3) Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)DP83825IRMQR
HVQFN-24-EP(3x3)-40℃~+85℃ 1.8V、3.3V 100BASE-TX、10BASE-TE 10Mbit/s、100Mbit/s 127mW Ethernet Transceiver RMII HVQFN-24-EP(3x3) Ethernet Transceivers ROHSTexas InstrumentsEthernet TransceiversW25Q64JVXGIM
XSON-8_4X4mm-40℃~+85℃ 100,000 cycles 10uA 133MHz 2.7V~3.6V 20 Years 3ms 64Mbit Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI XSON-8(4x4) NOR FLASH ROHSWinbond ElecGlobal Sourcing PartsMAX1562ESA+
SOIC-8-40℃~+85℃ 1 4A 4V~5.5V Active Low Load Switch SOIC-8 Power Distribution Switches ROHSMaxim Integrated (Analog Devices)Power Distribution SwitchesCC0603KRX7R6BB224
060310V 220nF X7R ±10% 0603 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMTRMCF0603FT56K0
0603-55℃~+155℃ 100mW 56kΩ Thick Film Resistor ±1% ±100ppm/℃ 0603 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface MountFBMH2012HM121-TV
08051 120Ω@100MHz 2.5A 32mΩ ±25% 0805 Ferrite Beads ROHSTaiyo YudenFerrite BeadsSP0503BAHTG
SOT-143-55℃~+125℃ 10A@8/20us 14V 150W@8/20us 30pF、60pF 5.5V 6V 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)LQM21PN4R7MGRD
0805288mΩ 30MHz 4.7uH 800mA Multilayer inductor ±20% 0805 Inductors (SMD) ROHSMurataInductors (SMD)BAT54C
SOT-231 Pair Common Cathode 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-23 Schottky Diodes ROHSNexperiaSchottky Diodes0ZCK0050FF2E
0805-40℃~+85℃ 100A 100ms 150mΩ 1A 500mA 500mW 6V 850mΩ 0805 Resettable Fuses ROHSBel FuseResettable Fuses
README
README.mdCustom Teensy 4.1 Microcontroller PCB
Overview
This repository covers the design of my custom take on the Teensy 4.1 from PJRC. Teensy 4.1 Site. I took inspiration from jenschrs design who incorporated usb-c rather than the intended USB-Micro, but lacked the SD slot, expandable RAM and flash memory, and PHY Ethernet IC and RJ45 Connection Like the original.



This Design, following the Teensy 4.1 official Schematic Features a 6 layer design with dedicated GND and 3.3V plane’s, and possesses the same RAM, Flash, Boot loader and MCU components as the original Teensy 4.1, but the 3.3V regulator was swapped for a NCP692 regulator providing essentially the same specs.
The Following are notable features in the Boards design:
- 2x USB-C connections, one for serial programming and power, and the other a host port for communication with serial to other devices
- Expandable IC footprints for a combination of either 2x additional 16mb PSRAM or 1x 16mb PSRAM and 1x 64mb FLASH
- DP83825L Ethernet PHY IC for interfacing with the MCU and the RJ45 Ethernet connector attached to the board for 10/100mbps internet
- micro SD slot
After assembling the first prototype with the supplied stencil from JLCPCB and a hot plate, and resolving a short issue from a solder bridge, The bootloader flashed the blink script to the memory and the board was able to achieve it, however serial communication wouldn’t work and windows device manager gave a error code 43. After a week of researching and forum questioning, I was able to locate the root problem to the ESD protection Diodes on the USB-C that I had used were rated for USB 2.0 and not 3.0, which was ruining the serial communication between my PC and the board. After desoldering these the board managed to show up on my PC and was finally able to communicate with it, albeit without ESD protection which can be replaced with a more suitable diode.
The Designing and assembly of this board taught me more design and assembly concepts such as:
- differential pairs and length matching design
- separation of analog and digital traces and components
- EMI ground shielding techniques
- positioning and selection of decoupling capacitors for electronic noise protection
- common via practices
- practice soldering SMD components with a hot plate and stencil effectively without overheating the temperature sensitive IC’s
- more practical experience isolating faults in a circuit, such as isolating shorts, identifying faulty components
- examining signals with an oscilloscope to ensure Ethernet signal integrity.
all while managing to keep the design cost effective. This board is the most complex I have designed and successfully assembled to date and I am eager to take these skills learnt to the next level with the next project the future brings.
Parts
92| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.22uf | Capacitor_SMD:C_0603_1608Metric | C1, C2, C4, C12, C13, C17, C19, C20, C23, C25, C31, C32 |
| 7 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7 |
| 5 | 4.7uf | Capacitor_SMD:C_0603_1608Metric | C6, C15, C22, C24, C26 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric | R3, R4, R6, R16 |
| 4 | Conn_01x11_Male | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J1, J2, J4, J5 |
| 3 | 10nf | Capacitor_SMD:C_0603_1608Metric | C5, C16, C29 |
| 3 | 10uf | Capacitor_SMD:C_0805_2012Metric | C14, C18, C21 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R8, R10, R15 |
| 3 | 2.2uf | Capacitor_SMD:C_0603_1608Metric | C3, C7, C27 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D2, D3, D4 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C8, C9 |
| 2 | 16k | Resistor_SMD:R_0603_1608Metric | R7, R11 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R5, R9 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 56k | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 2 | 9pF | Capacitor_SMD:C_0603_1608Metric | C10, C11 |
| 2 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6, J7 |
| 2 | Ferrite_Bead | Resistor_SMD:R_0805_2012Metric | FB1, FB2 |
| 2 | SP0503BAHT | Package_TO_SOT_SMD:SOT-143 | D1, Di3 |
| 2 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | USB_DFP1, USB_UFP1 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C30 |
| 1 | 0.22uf | Capacitor_SMD:C_0805_2012Metric | C28 |
| 1 | 150R | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | 2.2M | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 24MHz | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | 2nd PSRAM/Flash APS640L 3SQR / 25q128JVSQ (2) | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U8 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_TXC_9HT11-2Pin_2.0x1.2mm_HandSoldering | Y2 |
| 1 | 4.7uH | Capacitor_SMD:C_0805_2012Metric | L1 |
| 1 | 6.49K | Resistor_SMD:R_0603_1608Metric | R18 |
| 1 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D5 |
| 1 | Conn_01x12_Male | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J3 |
| 1 | DP83825IRMQR | Teensy_Footprint_library:XCVR_DP83825IRMQR | U5 |
| 1 | Fuse | Resistor_SMD:R_0805_2012Metric | F1 |
| 1 | J1B1211CCD | Teensy_Footprint_library:J1B1211CCD | P1 |
| 1 | MAX1562 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | MIMXRT1062DVJ6B | Teensy_Footprint_library:BGA196C80P14X14_1200X1200X152N | U1 |
| 1 | MKL02Z32VFG4 | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.9x1.9mm | U3 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J8 |
| 1 | OnSemi NCP692, fixed version | Package_DFN_QFN:DFN-6-1EP_3x3mm_P0.95mm_EP1.7x2.6mm | NCP692 |
| 1 | PSRAM APS640L 3SQR (1) | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | Q_PMOS_GDS_DMP3125L | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_1x07_P1.27mm_Vertical | SWD1 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T-SH_NO_CK_KMR2xxG | PROG1 |
| 1 | W25Q64JVXGIM | Teensy_Footprint_library:XSON8_4x4mm | U6 |
| 1 | opto_APA102-2020 | LED_SMD:LED-APA102-2020 | U2 |
Similar boards
- 4 layers61.5 × 47.5 mm

- 4 layers49.6 × 99.8 mm

FlightPCB
Shubhamai/tsar
General-purpose & fully programmable flight computer PCB desgined in KiCad EDA
205 parts - 4 layers194 × 94 mm

- 4 layers17.8 × 33 mm

Nrf54l smol
picafe/nrf54l_smol
Ebyte E73-2G4M08S1F nRF54L15-based dev board with similar form factor to Pro Micro/Supermini
29 parts - 4 layers45 × 45 mm

- 4 layers80 × 80 mm

- 6 layers183.6 × 143.9 mm

ExoAnchor P4 V2.4A6
wxffxx/ExoAnchor-Hardware
This repository contains ExoAnchor hardware design outputs and hardware-specific instructions. Firmware, system architecture, and board capability truth live in the main ExoAnchor repository.
195 partsMIT - 6 layers55 × 35 mm

Pilot
Stab-Rabbit-coding/Serenity-UAV
A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..
136 parts1CERN-OHL-W-2.0
Questions
How big is the Teensy 4.1 attempt 1 PCB?
It measures 87.6 × 53.9 mm and has 6 copper layers, 1.51 mm thick.
What parts does the Teensy 4.1 attempt 1 use?
92 parts, built around the MIMXRT1062DVJ6B, MKL02Z32VFG4, DP83825IRMQR and W25Q64JVXGIM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Teensy 4.1 attempt 1 KiCad files?
From the Wierdwizard2587/Custom-Teensy-4.1-PCB-Design repository on GitHub, at the commit this page was made from: the board is Kicad Files/Teensy_4.1_attempt_1.kicad_pcb and its schematic Kicad Files/Teensy_4.1_attempt_1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Teensy 4.1 attempt 1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Wierdwizard2587 before reusing the design.