

Esplog hv
- Size
- 16.6 × 11.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 36
- Pads
- 120
- Tracks, vias
- 254, 51
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 30 Aug 2022
- Updated
- 30 Dec 2025
Overview
Esplog hv is an open-source printed circuit board by VladimirP1, from the VladimirP1/esplog-hardware repository on GitHub. It is a 2-layer board of 16.6 × 11.8 mm with 35 parts on 36 nets, routed with 254 tracks and 51 vias.
It is built around the ESP32-C3, RY8310 and BMI160, with the VLS3012HBX-4R7M among its other parts. Its parts include 13 capacitors, 4 resistors, 3 ICs, 2 diodes and 2 inductors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
4ESP32-C3
QFN-32-EP(5x5)12bit 160MHz 22 3V~3.6V Others QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSEspressif SystemsMicrocontrollers (MCU/MPU/SOC)RY8310
SOT-23-6-40℃~+85℃@(TA) 1 1.4MHz 1A 4.5V~30V 600uA Adjustable Buck Buck Built-in Yes SOT-23-6 DC-DC Converters ROHSRYCHIP Semiconductor Inc.DC-DC ConvertersBMI160
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 10uA 16bit 1KB IMU (accelerometer + gyroscope) Motion event detection、Synchronization and timestamp SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSBosch SensortecAccelerometersVLS3012HBX-4R7M
SMD,3x3mm175mΩ 2.01A 2.51A 4.7uH ±20% SMD,3x3mm Power Inductors ROHSTDKPower Inductors
README
README.mdWhat is this
These are boards for running the esp-gyrologger firmware. They contain an esp32-c3, a mems IMU and 3.3v a regulator. Wi-Fi antenna is bad, but it works at low TX power.
esplog-hv accepts 4-30v input
esplog-ldo accepts 4-6v input
How the finished product look like
This is how esplog_ldo and esplog_hv look like
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 |
| 5 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C6, C8, C9, C12 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R3, R4 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C11, C13, C14 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C3, C10 |
| 1 | - | Diode_SMD:D_SOD-523 | D1 |
| 1 | 22u | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 2n | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 31.6k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 40M | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | BMI160 | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U2 |
| 1 | ESP32-C3 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LOGO | esplog_logo:esplog_logo | G*** |
| 1 | RY8310 | Package_TO_SOT_SMD:SOT-23-6 | IC1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | VLS3012HBX-4R7M | tdk_inductor:VLS3012 | L2 |
More from VladimirP1/esplog-hardware
1- 2 layers13.5 × 10.7 mm

Similar boards
- 2 layers

- 2 layers180 × 131.1 mm

CCController
RainbowLabsDE/LightInstallationController
PCB and Firmware of our first universal RGB light installation controller.
92 parts4MIT - 2 layers25 × 46.3 mm

Dimmer
flaviut/led-dimmer
Open-source hardware for dimming LED strips, using ESPHome software
47 parts2 - 4 layers50 × 62 mm

Powermeter1P1I
RainbowLabsDE/PowerMeasure_1Ph
this repo is still undergoing major changes and should not yet be rebuilt
79 parts1MIT - 4 layers119 × 39 mm

Controller Room
crexodon/LED-Window-Matrix-Neo
Turning the campus building into a led display
79 partsMIT - 4 layers45 × 60 mm

- 4 layers52 × 36 mm

- 2 layers90 × 67.5 mm

SensactHsIO5
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
215 parts4Apache-2.0
Questions
How big is the Esplog hv PCB?
It measures 16.6 × 11.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esplog hv use?
35 parts, built around the ESP32-C3, RY8310, BMI160 and VLS3012HBX-4R7M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esplog hv KiCad files?
From the VladimirP1/esplog-hardware repository on GitHub, at the commit this page was made from: the board is esplog_hv/esplog_hv.kicad_pcb and its schematic esplog_hv/esplog_hv.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esplog hv design in my own project?
Its repository states no licence, so its author keeps all rights: ask VladimirP1 before reusing the design.