
Output.Panel R0.5.1 300x300 2layer step1 Modified
rusefi/hw_microRusEfi
microRusEfi board for rusEfi ECU

The RedPill, for when you realize the BluePill just doesn't cut it
RedPill is an open-source printed circuit board by TobleMiner, from the TobleMiner/STM32-RedPill repository on GitHub, published under the MIT licence. It is a 4-layer board of 20.4 × 50.9 mm with 48 parts on 71 nets, routed with 518 tracks and 119 vias.
It is built around the SRV05-4 and B5819W. Its parts include 16 capacitors, 8 resistors, 7 diodes, 6 connectors and 3 ICs. It belongs with the STM32 boards of this library.
The RedPill, for when you realize the BluePill just doesn't cut it.
The RedPill is designed as a more powerful drop-in replacement for the
BluePill. While .1" wider the RedPill is fully pin-compatible to the
BluePill.
The following table summarizes the most important differences between
RedPill and BluePill:
| RedPill | BluePill | |
|---|---|---|
| MCU | STM32F722REC6 | STM32F103C8T6 |
| ARM core | Cortex-M7 | Cortex-M3 |
| Max system clock | 216MHz | 72MHz |
| Flash | 256kB | 128kB |
| SRAM | 256kB | 20kB |
| Programming | DFU, SWD | SWD |
| USB connector | USB Type C | Micro USB Type B |
| SD card | MicroSD | - |
| LEDs | 5 | 1 |

| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 5.1kR | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
| 7 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C8, C9, C11, C16 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C10, C12 |
| 2 | 20pF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 33pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | Conn_01x20 | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J1, J2 |
| 2 | ToolingHole | ToolingHole:ToolingHole_JLCSMT | H1, H2 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C13 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D1 |
| 1 | BLU | LED_SMD:LED_0603_1608Metric | D6 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J5 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | Crystal | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | GRN | LED_SMD:LED_0603_1608Metric | D7 |
| 1 | Icon | Icon:pill | H3 |
| 1 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | Micro_SD_Card | Connector_Card_MicroSD:XUNPU_TF.104 | J6 |
| 1 | OSHW | Symbol:OSHW-Symbol_6.7x6mm_SilkScreen | H4 |
| 1 | PC13 | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | PWR | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | STM32F722RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SW_Push | XKB_switch:TS-1187A-X-X-X | SW1 |
| 1 | TagConnect_TC2030_SWD | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J4 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | J3 |
| 1 | WHT | LED_SMD:LED_0603_1608Metric | D5 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23 | U3 |
| 1 | YLW | LED_SMD:LED_0603_1608Metric | D4 |

rusefi/hw_microRusEfi
microRusEfi board for rusEfi ECU


VIPQualityPost/aioli-foc
Small, simple closed loop BLDC driver implementing SimpleFOC


TheButlah/slimevr_pcb
A collection of PCBs designed for SlimeVR full-body trackers

kfilipekk/iridium_drone
STM32H743 flight controller that navigates without GPS from Iridium satellite Doppler

rjsc/BECom
BECom - Battery Emulator Companion - Open Source Hardware, designed to run dalathegreat/Battery-Emulator

ArduProject/PCB_DRONE_C8
En este repositorio encontrareis los archivos de fabricación y las listas de montaje del PCB con STM32F103C8 que hemos visto en el curso.
It measures 20.4 × 50.9 mm and has 4 copper layers, 1.6 mm thick.
48 parts, built around the SRV05-4 and B5819W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TobleMiner/STM32-RedPill repository on GitHub, at the commit this page was made from: the board is RedPill.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).