

Wildgaurd
- Size
- 132 × 101 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 55
- Pads
- 158
- Tracks, vias
- 272, 0
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 11 Apr 2026
- Updated
- 11 Apr 2026
Overview
Wildgaurd is an open-source printed circuit board by Thea-28, from the Thea-28/wildgaurd repository on GitHub. It is a 2-layer board of 132 × 101 mm with 24 parts on 55 nets, routed with 272 tracks and 0 vias.
It is built around the ESP32-WROOM-32, AMS1117-3.3 and TP4056-42-ESOP8. Its parts include 14 connectors, 3 ICs, 2 capacitors and 2 resistors. It belongs with the ESP32 boards of this library.
Main components
3ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTP4056-42-ESOP8
ESOP-8-40℃~+85℃ 1 1A 2uA 4.2V 4V~8V Charging IC Lithium Battery Support ESOP-8 Battery Management ROHSTOPPOWERBattery Management
README
README.md🌿 WildGuard IoT System
🚀 Overview
WildGuard is an IoT-based smart wildlife monitoring and protection system designed to prevent human-animal conflicts and ensure real-time tracking and surveillance.
🧠 Features
- 📍 GPS Tracking for location monitoring
- 🎥 ESP32-CAM for live video feed
- 🔴 IR Sensors for obstacle/animal detection
- 📡 RFID for identification
- 🚗 Motor Control using TB6612 Driver
- ⚡ Efficient Power Management (12V → 5V → 3.3V)
🧩 Components Used
- ESP32
- ESP32-CAM
- Neo-6M GPS Module
- RFID RC522
- IR Sensors
- TB6612 Motor Driver
- 12V DC Motors
- Buck Converter (LM2596)
- AMS1117 Voltage Regulator
🔌 System Architecture
- 12V supply powers motors
- Buck converter steps down to 5V
- AMS1117 regulates 3.3V for ESP32 and sensors
- ESP32 acts as the main controller
🛠️ Technologies
- Embedded Systems
- IoT
- PCB Design (KiCad)
- Wireless Communication
📂 Project Structure
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | Resistor_SMD:R_0815_2038Metric | R1, R2 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | Motor_DC | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | M1, M2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_Horizontal | J11 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_1042_1x18650 | BT1 |
| 1 | Boost 12v in | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | Boost 12v out | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | Boost 5v in | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Boost 5v out | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | Buck (LM2596) | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | ESP32 CAM | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J14 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | GPS neo 6m | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | IR_Sensor1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J17 |
| 1 | IR_Sensor2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J15 |
| 1 | Motor Driver | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J6 |
| 1 | OLED | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | RFID RC522 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J7 |
| 1 | Solar | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | TP4056-42-ESOP8 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U2 |
Similar boards
- 4 layers88 × 58 mm

- 4 layers41 × 90.2 mm

- 2 layers150.5 × 94 mm

Rx module
koushik12328/Smart_mining_helmet
An ESP32-powered safety helmet featuring gas detection, impact sensing, and IoT connectivity
30 partsMIT - 2 layers71.2 × 78.4 mm

- 2 layers45 × 35.5 mm

- 4 layers100 × 70.5 mm

Smart Irrigation SystemV2
Benedikt3141/Smart-Irrigation-System
A smart irrigation system for irrigation of up to 6 plants. It monitors the moisture, temperature, CO2 concentration, air quality ... and displays the data on a 2.4" TFT Display using an ESP32 DevKit C as processor.
147 parts1MIT - 2 layers

Unplugged
Kalash4152/smart-dustbin-round-two
Designed and simulated a Smart Dustbin & Smart Traffic Lights system using Arduino, ESP32, and sensors at DJSCE Unplugged 2.0.
24 parts1 - 2 layers49.4 × 95.7 mm

Questions
How big is the Wildgaurd PCB?
It measures 132 × 101 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wildgaurd use?
24 parts, built around the ESP32-WROOM-32, AMS1117-3.3 and TP4056-42-ESOP8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wildgaurd KiCad files?
From the Thea-28/wildgaurd repository on GitHub, at the commit this page was made from: the board is Wildgaurd.kicad_pcb and its schematic Wildgaurd.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wildgaurd design in my own project?
Its repository states no licence, so its author keeps all rights: ask Thea-28 before reusing the design.