
Dash 6.8
romioRN/Dash6.8-hardware
wifi name "service", password 12345678, connect to 192.167.4.1

ESP32-S3 development board with USB-C power, programming and ESD protection (KiCad)
Micro Controller V1 is an open-source printed circuit board by TariqKF, from the TariqKF/mcu-power-programming-board repository on GitHub. It is a 2-layer board of 51.8 × 32.6 mm with 18 parts on 44 nets, routed with 470 tracks and 33 vias.
It is built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3 and USBLC6-2SC6. Its parts include 7 capacitors, 3 resistors, 3 ICs, 3 connectors and 2 switches. It belongs with the microcontroller boards boards and the ESP32 boards of this library.
Custom ESP32-S3 development board designed in KiCad.
Micro-Controller-V1.kicad_sch: schematicMicro-Controller-V1.kicad_pcb: PCB layoutMY_Footprints.pretty/: custom ESP32-S3-WROOM-1 footprintOpen Micro-Controller-V1.kicad_pro in KiCad 10.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4 |
| 2 | 22uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C6, C7 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | Conn_01x20_Pin | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J1, J2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW1, SW2 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 1uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |

romioRN/Dash6.8-hardware
wifi name "service", password 12345678, connect to 192.167.4.1


dulerabbit/GaggiBre-legacy
This is GaggiBre! a fork of Gaggimate with Manual Brew Control and Adaptive Mode. Made by Dule Rabbit

mornepousse/Niphargus
Niphargus — a slim, indestructible wireless split keyboard. ESP32 + nRF24, wired fallback, and an emergency kit hidden behind the USB port. The successor to the Rouge-Gorge.

ODARI-CHARLES1/iot_device_pcb
Hardware design for a air conditioner pcb design using Kicad software. This is for learning purpose only not manufacturable.

zinkwazi/traffic-pcb-sb
In the lower left corner of the board is the control panel and above that is the direction panel. The three chips located throughout the board are LED matrix drivers which receive commands via I2C from the ESP32S3.


Igur7/AngleCircle
Celem projektu jest integracja elektroniki, zasilania i czujników w jednym module oraz ograniczenie problemów z połączeniami przewodowymi, które występowały na etapie prototypowania.
It measures 51.8 × 32.6 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TariqKF/mcu-power-programming-board repository on GitHub, at the commit this page was made from: the board is Micro-Controller-V1.kicad_pcb and its schematic Micro-Controller-V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask TariqKF before reusing the design.