4 layers40.5 × 48.8 mm
ESP32 Flight Conroller
Maxandersen1/ESP32-S3-Flight_Controller
Custom ESP32 Flight Controller using BMI088 & BMP388 sensors. Hardware and firmware built from the ground up.
52 partsMIT
2 layers59.5 × 40 mm
Monitor
Dynix7/Environment-Monitor1- Size
- 59.5 × 40 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 49
- Nets
- 58
- Pads
- 234
- Tracks, vias
- 432, 65
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 9 May 2026
- Updated
- 12 Jun 2026
Overview
Monitor is an open-source printed circuit board by Dynix7, from the Dynix7/Environment-Monitor repository on GitHub, published under the MIT licence. It is a 2-layer board of 59.5 × 40 mm with 49 parts on 58 nets, routed with 432 tracks and 65 vias.
It is built around the ESP32-S3-WROOM-1-N8, AGS10 and AHT20, with the BMP388, LTR-303ALS-01 and AMS1117-3.3 among its other parts. Its parts include 18 capacitors, 14 resistors, 11 ICs, 2 diodes and 2 connectors. It belongs with the ESP32 boards of this library.
Main components
8
ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
AGS10
SMD-4P,5x4mm0ppm~100ppm 2.9V~3.1V 28mA Hazardous Gas I2C ±25% SMD-4P,5x4mm Gas Sensors ROHSAosong ElecGas Sensors
AHT20
SMD-40℃~+120℃ 0%RH~100%RH 2.2V~5.5V 20bit 570uA I2C ±0.3℃ ±2%RH SMD Temperature and Humidity Sensor ROHSAosong ElecTemperature And Humidity Sensor
BMP388
LGA-10(2x2)-40℃~+85℃ 1.65V~3.6V 1pa/K 2uA 30Kpa~1.25bar 50pa 8pa I2C、SPI LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure Sensors
LTR-303ALS-01
DFN-6(2x2)-30℃~+70℃ 0.7mm 16bit 2.4V~3.6V 2mm 2mm 64klx I2C Light Intensity Low power/sleep mode、Spectral correction/filtering、Adjustable gain control、Interrupt/event trigger、Built-in temperature compensation DFN-6(2x2) Ambient Light Sensors ROHSLite-OnAmbient Light Sensors
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
BQ24075RGT
QFN-16-EP(3x3)-40℃~+125℃ 1.5A 4.2V 4.35V~6.4V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery Management
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
README
README.mdEnvironment-Monitor
This is a board that serves as an environment sensor, recording the temperature, humidity, air pressure, brightness, and air quality of the area around it. It does this through the use of 5 sensors: TMP102AIDR, AHT20-F, BMP388, LTR303, and AGS10. The information can be displayed of the built in SSD1306 0.91 screen.
Why I Made It
Not surprisingly I spend a lot of time sitting indoors in my room on my computer. With this, I often have my door closed and sometimes the window open. I wanted a device that can monitor my room so I can make optimize my environment so if it detects that it's getting to hot (for example) I can open the window more or open my door.
Pictures
BOM
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C4, C7, C12, C13, C14, C15, C16, C17, C18 |
| 8 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C2, C3, C5, C6, C8, C9, C10, C11 |
| 4 | 5k1 | Resistor_SMD:R_0603_1608Metric | R4, R5, R9, R14 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R6, R10, R11 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | 2k2 | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 1 | 3k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 4k3 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 62k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | AGS10 | AGS10:AGS10 | U1 |
| 1 | AHT20 | AHT20:PSON100P300X300X110-6N | U8 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | AP2112K-3.0 | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | BAT | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | BMP388 | BMP388:XDCR_BMP388 | U4 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_PTS647_Sx38 | SW2 |
| 1 | BQ24075RGT | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm | U2 |
| 1 | CHG | LED_SMD:LED_1206_3216Metric | D2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U10 |
| 1 | LTR-303ALS-01 | OptoDevice:Lite-On_LTR-303ALS-01 | U7 |
| 1 | PGD | LED_SMD:LED_1206_3216Metric | D1 |
| 1 | RST | Button_Switch_SMD:SW_SPST_PTS647_Sx38 | SW1 |
| 1 | SSD1306 | Display:ER_OLEDM0.91_1x-I2C | U11 |
| 1 | TMP102xxDRL | Package_TO_SOT_SMD:SOT-563 | U9 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
Similar boards
- 4 layers55 × 55 mm
- 4 layers106 × 88 mm
Luchtmeter
KVR-CIBER/luchtmeter-s3
ESP32-S3 luchtmeter: 4.3in touch, SCD41/SHT45/LTR-303, NFC, LiPo, ESPHome + behuizing
76 parts - 2 layers82 × 50 mm
ESP S3 MONITOR V 1 2
electromotif208/pcb-portfolio
👨💻 Electronics Engineer 📺 YouTube: ELECTROMOTIF 🔧 Tools: KiCad, EasyEDA 📡 Domains: Power Supply, ESP32, IoT, Embedded Hardware
90 parts - 2 layers100 × 50 mm
DSP Regulator HAT Rev D My Edits
Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting
75 parts - 4 layers89.5 × 96.8 mm
MicroPad
JonasLindinger/MicroPad
Battery-efficient ESP32-S3 macro pad with a 2.9" e-paper display for controlling Home Assistant. Pages and per-key actions are configured in a web tool and pushed over MQTT — no reflashing for menu or key changes.
72 parts2MIT - 4 layers38 × 55 mm
- 4 layers66 × 40 mm
ESP32 PRELIM DESIGN
ece49022-team9/slate
Keep the team's native schematic and board sources here, including any project-specific libraries needed to open them.
82 parts
Questions
How big is the Monitor PCB?
It measures 59.5 × 40 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Monitor use?
49 parts, built around the ESP32-S3-WROOM-1-N8, AGS10, AHT20 and BMP388. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Monitor KiCad files?
From the Dynix7/Environment-Monitor repository on GitHub, at the commit this page was made from: the board is PCB/Monitor.kicad_pcb and its schematic PCB/Monitor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Monitor design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).