
ATTiny1616-S
shreejita56/ATTINY
I made a small devboard based on Atinny1616-S .It has inbuild 3.3V voltage regulator and a USB-to-UART serial convertor .Power and data comes from USB-C . The board has an inbuilt LED.

Resolution w7 is an open-source printed circuit board by Sushi-Mampfer, from the Sushi-Mampfer/resolution_hardware_w7 repository on GitHub. It is a 2-layer board of 90 × 38.8 mm with 17 parts on 31 nets, routed with 132 tracks and 3 vias.
It is built around the ATTINY1616-SN, CH340X and HS96L03W2C03. Its parts include 5 capacitors, 4 ICs, 4 switches, 3 resistors and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.
A pretty big devboard for the ATTINY1616, with 4 buttons and a screen, perfect to play pong with a friend.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | SW_Push | Button_Switch_THT:SW_PUSH-12mm | SW1, SW2, SW3, SW4 |
| 3 | 1uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1, C2, C4 |
| 2 | 5.1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C5 |
| 1 | 100nF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C3 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3 |
| 1 | ATtiny1616-S | easyeda2kicad:SOIC-20_L13.0-W7.6-P1.27-LS10.3-BL | U2 |
| 1 | CH340X | Package_SO:MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | HS96L03W2C03 | easyeda2kicad:OLED-TH_L27.8-W27.2-P2.54_C9900033791 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | easyeda2kicad:USB-C-SMD_TYPE-C-16PIN-2MD-073 | J1 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23-3 | U1 |

shreejita56/ATTINY
I made a small devboard based on Atinny1616-S .It has inbuild 3.3V voltage regulator and a USB-to-UART serial convertor .Power and data comes from USB-C . The board has an inbuilt LED.

CmdrZin/chips_avr_examples
AVR assembly and C code for robotics and other projects.


fjalvingh/8bit-busdisplay
PCB for showing an 8 bit hex number from a 5V bus on a 7-segment display using an ATTINY1616

Bumb1eris/PCB_Business_Card
A coin cell powered PCB business card that can play snake



empdo/lightmeter
An open-hardware handheld photographic light meter. Set shutter speed and ISO on two dials, press the button, and one of nine LEDs lights up to show the aperture you should use. Runs from a single CR2032.
It measures 90 × 38.8 mm and has 2 copper layers, 1.6 mm thick.
17 parts, built around the ATTINY1616-SN, CH340X and HS96L03W2C03. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Sushi-Mampfer/resolution_hardware_w7 repository on GitHub, at the commit this page was made from: the board is src/kicad/resolution_w7.kicad_pcb and its schematic src/kicad/resolution_w7.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Sushi-Mampfer before reusing the design.