4 layers50 × 40 mm
4 layers99 × 59 mm
Gps watch
SuperTails/gps-watchCode and design files for the Landhopper GPS watch
- Size
- 99 × 59 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 90
- Nets
- 76
- Pads
- 302
- Tracks, vias
- 479, 104
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 8 Feb 2024
- Updated
- 4 May 2024
Overview
Gps watch is an open-source printed circuit board by SuperTails, from the SuperTails/gps-watch repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 99 × 59 mm with 90 parts on 76 nets, routed with 479 tracks and 104 vias.
It is built around the 74AHC1G04SE, MAX-M10S and S-1317A33-M5T1U4, with the PMEG4005EH and SI2319CDS among its other parts. Its parts include 19 capacitors, 12 resistors, 11 connectors, 7 ICs and 7 diodes. It belongs with the radio and wireless and wearables boards and the STM32 boards of this library.
Main components
5
74AHC1G04SE
SOT-353-40℃~+125℃ 1 1 1.5V~3.85V 1.9V、2.9V、4.4V 1uA 2V~5.5V 500mV~1.65V 7.5ns@5V,50pF 74AHC 8mA 8mA Noise suppression function Schmitt trigger SOT-353 Inverters ROHSDiodes IncorporatedInverters
MAX-M10S
LCC-18_10.1X9.7LCC-18_10.1X9.7 New Arrivals ROHSu-bloxUncategorised
S-1317A33-M5T1U4
SOT-23-5-40℃~+85℃ 3V 5.5V Fixed Over Current Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSABLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
PMEG4005EH
SOD-1231 Independent 100uA@40V 10A 40V 470mV@500mA 500mA SOD-123 Schottky Diodes ROHSNexperiaSchottky Diodes
SI2319CDS
SOT-23-55℃~+150℃ 1 P-Channel 108mΩ@4.5V 2.5V 2.5W 21nC@10V 4.4A 40V 595pF 61pF 76pF P-Channel SOT-23 MOSFETs ROHSVishay IntertechnologyMOSFETs
README
README.mdGPS Watch "Landhopper": Firmware
Carnegie Mellon University
18-500 ECE Design Experience, Spring 2024
Gary Bailey, Carson Swoveland, Twain Byrnes
To build, make sure the thumbv7em-none-eabihf target is installed. Deploy with
cargo run to use probe-rs, or use openocd -f openocd.cfg and gdb-multiarch -x gdb.cfg
to enter a debugger.
Parts
90| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | TestPoint | TestPoint:TestPoint_Loop_D3.80mm_Drill2.5mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12 |
| 10 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C2, C3, C4, C5, C13, C14, C16, C17, C18, C19 |
| 6 | PMEG4005EH | Diode_SMD:D_SOD-123F | D1, D2, D3, D4, D5, D6 |
| 5 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C6, C7, C8, C15 |
| 4 | 1M | Potentiometer:POT_PV36W_MUR | RV1, RV2, RV3, RV4 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R13 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R8, R9 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric | R14, R15 |
| 2 | 4.3pF | Capacitor_SMD:C_0805_2012Metric | C10, C11 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R10, R11 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2, J8 |
| 2 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6, J11 |
| 2 | Jumper_2_Bridged | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP2, JP3 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 1R | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 22u | inductor_wurth:IND_4818-WE-TPC_WRE | L1 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | 33k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 74AHC1G04 | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | 82k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | ADP5090ACP | Package_CSP:LFCSP-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm | U3 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_15x7.5RM7.6 | BZ1 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J4 |
| 1 | Conn_01x03_Pin | Connector_Molex:Molex_PicoBlade_53047-0310_1x03_P1.25mm_Vertical | J1 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Conn_01x10 | panasonic:ayf531035 | J9 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_Vertical | J7 |
| 1 | Crystal | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | D_Zener | Diode_SMD:D_0402_1005Metric | D7 |
| 1 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | LOGO | careers:bnyahaj | G*** |
| 1 | LOGO | careers:salix | G*** |
| 1 | LOGO | careers:sky | G*** |
| 1 | MAX-M10S | RF_GPS:ublox_MAX | U5 |
| 1 | MCP6401T-xOT | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | MCP73831-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | MEM2061-01-188-00-A_REVA | MEM2061_01_188_00_A:GCT_MEM2061-01-188-00-A_REVA | J12 |
| 1 | R_US | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | S-1317A33-M5T1U4 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | STM32L412KBTx | Package_QFP:LQFP-32_7x7mm_P0.8mm | U4 |
| 1 | SW_5Way_Tactile | sw_tactile:SW_5Way_Tactile | SW3 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | SW_SPDT | Button_Switch_THT:SW_Slide_1P2T_CK_OS102011MS2Q | SW2 |
| 1 | Si2319CDS | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
More from SuperTails/gps-watch
1Similar boards
- 4 layers98 × 98 mm
- 4 layers82 × 100.2 mm
- 2 layers
HFL
danielortval/RamRacing-EV-PCBs
Full schematic and PCB designs for RAM Racing’s Formula SAE Electric Vehicle. Includes tractive system active light, hard fault latch, precharge/discharge circuits, and the complete EV schematic.
30 parts2 - 4 layers19 × 111.1 mm
Gliss main
BelaPlatform/gliss-hardware
You can find the source KiCad files for the Gliss module in this repository. This project is open hardware and under the Creative Commons Share Alike license 4.0.
107 parts18 - 2 layers115 × 115 mm
- 2 layers99.6 × 53 mm
RP2040GPSTracker
justsem/RP2040-868
A GPRS/GNSS/BTLE and LiPo/Li-ion charger integrated Pi Pico on credit-card format.
176 parts11CC-BY-SA-4.0 - 2 layers100 × 100 mm
BQ76pl455a
g-rahul/BQ76PL455A-EVM-Clone
This respository contains low cost design files for BQ76PL455A-EVM Clone.
255 parts5 - 2 layers40 × 61 mm
Questions
How big is the Gps watch PCB?
It measures 99 × 59 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Gps watch use?
90 parts, built around the 74AHC1G04SE, MAX-M10S, S-1317A33-M5T1U4 and PMEG4005EH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gps watch KiCad files?
From the SuperTails/gps-watch repository on GitHub, at the commit this page was made from: the board is pcb/prototype/gps_watch.kicad_pcb and its schematic pcb/final/gps_watch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gps watch design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).