
CoralC5-Motor
SmallCoral/c5-car
用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。

用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。
CoralC5-Motor is an open-source printed circuit board by SmallCoral, from the SmallCoral/c5-car repository on GitHub. It is a 2-layer board with 187 parts on 187 nets, routed with 151 tracks and 3 vias.
It is built around the SN74LV1T125DBVR-TP, SN74LVC2G125DCTR-JSM and SN74LVC2G17DCKR, with the LTC4412ES6#TRMPBF, AP2112K-3.3TRG1 and EEUFR1E471Y among its other parts. Its parts include 68 resistors, 59 capacitors, 15 ICs, 14 connectors and 9 transistors. It belongs with the robots and motor control boards of this library.
用 KiCad 10 打开 CoralC5-Expansion.kicad_pro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。
板上包括 LAN8720A 百兆网口及 50MHz 时钟、SPI3 microSD、带 MHF III 外置天线座的 Wi-Fi/Bluetooth LE 模块、5V 入口和独立 AP63203 降压。J1 输入稳压 5V、2A,U6 的 +3V3_EXP 给本板外设供电;金手指和排针上的 +3V3 来自 Core,外接负载预算合计 100mA,两路输出不并联。J14 已同步 C5-EDGE-3 自定义针序,须与同版 Core 配对。J9 的 31、32 脚直接连接 Core 的 PC14、PC15,33、34 脚不连接;PH0、PH1 留在 Core 晶振回路。其余排针顺序保持原样,共引出 84 路 GPIO。
J12 是四线 SWD,JST XH 2.50mm,顺序固定为 1 脚 3V3/VTref、2 脚 SWDIO、3 脚 SWCLK、4 脚 GND。TP5 为 NRST,TP6 为 VREF_MCU。SW3、SW4 是 ESP 复位和下载按键,已改为两脚 3×6×2.5 贴片款,参考 SD-1107 图纸,本体实际 6.1×3.6mm、高 2.5mm。
本板有七页原理图,见 电路 PDF,排针与金手指对应关系放在 header_pinout.csv,元件清单在 BOM.csv。73 个采购位号均绑定本地模型,其中 U4、J3、Y3 和两个按键使用通用外形,两个测试点不需要采购模型。

ERC 为 0 错误、0 警告,PCB 与原理图一致性检查为 0。PCB 尚未布线,有 314 个未连接项;J14 的 51 号固定焊盘到定位孔只有 0.05mm,低于当前 0.25mm 规则,需按母座原厂推荐焊盘复核修订。当前文件不作为制板发布版,接口边界和待处理项目见 共同说明。
2026 年 10 月 23 日全检确认当前电路与主控接口对应,PCB 仍未布线。PHY、无线和 SD 卡的部分去耦电容离电源脚约 7~16mm,需要在布线前重排。详细距离和全检结果见 双板检查记录。
| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 10k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R7, R13, R18, R19, R33, R38, R39, R50, R51, R52, R53, R54, R55, R56, R57, R58 +4 |
| 16 | 100k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R1, R14, R34, R74, R75, R77, R78, R79, R80, R81, R84, R86, R87, R88, R89, R90 |
| 9 | 100n / 16V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C4, C11, C14, C16, C19, C31, C34, C36, C39 |
| 9 | 100nF/50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C51, C65, C69, C72, C74, C75, C76, C79, C80 |
| 6 | 1k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R15, R16, R17, R35, R36, R37 |
| 5 | DMP3007LK3-13 | Motor:Package_TO_SOT_SMD__TO-252-2 | Q1, Q2, Q5, Q6, Q7 |
| 4 | 100nF | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C57, C58, C59, C60 |
| 4 | 10k / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R10, R11, R30, R31 |
| 4 | 1n / 16V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C17, C18, C37, C38 |
| 4 | 22uF/10V X7R | Motor:Capacitor_SMD__C_1206_3216Metric | C52, C53, C66, C67 |
| 3 | 100n / 50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C3, C12, C32 |
| 3 | 10uF/10V | Motor:Capacitor_SMD__C_0805_2012Metric | C61, C62, C78 |
| 3 | 15k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R66, R69, R71 |
| 3 | 470u / 25V | Motor:Capacitor_THT__CP_Radial_D10.0mm_P5.00mm | C1, C13, C33 |
| 3 | BSS138BK | Motor:Package_TO_SOT_SMD__SOT-23 | Q3, Q4, Q9 |
| 2 | 1.82k / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R12, R32 |
| 2 | 10n / 16V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C15, C35 |
| 2 | 10uF/25V X7R | Motor:Capacitor_SMD__C_1206_3216Metric | C50, C64 |
| 2 | 158k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R59, R61 |
| 2 | 1u / 10V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C20, C40 |
| 2 | 1uF/10V X7R | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C54, C55 |
| 2 | 22n / 50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C10, C30 |
| 2 | 22u / 10V | Motor:Capacitor_SMD__C_1206_3216Metric | C5, C6 |
| 2 | 30.1k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R60, R62 |
| 2 | 4.7k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R2, R82 |
| 2 | 47pF/50V C0G | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C63, C68 |
| 2 | 6.8uH / 5.1A | Motor:L_Bourns_SRN8040TA_GenericBody | L2, L3 |
| 2 | AP63300WU-7 | Motor:Package_TO_SOT_SMD__TSOT-23-6 | U6, U8 |
| 2 | DRV8874PWPR | Motor:DRV8874_PWP0016 | U2, U4 |
| 2 | MG513 / XH2.50 / 6P | Motor:Connector_JST__JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J4, J6 |
| 2 | SN74LV1T125DBVR | Motor:Package_TO_SOT_SMD__SOT-23-5 | U11, U12 |
| 2 | SN74LVC2G125DCTR | Motor:Package_SO__SSOP-8_2.95x2.8mm_P0.65mm | U13, U15 |
| 2 | SN74LVC2G17DCKR | Motor:Package_TO_SOT_SMD__SOT-363_SC-70-6 | U3, U5 |
| 2 | TFT孔 D2.0 | Motor:MountingHole__MountingHole_2mm | H1, H2 |
| 2 | 供电使能跳线 | Motor:Connector_PinHeader_2.54mm__PinHeader_1x02_P2.54mm_Vertical | J26, J27 |
| 1 | 100R | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R6 |
| 1 | 100k / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R4 |
| 1 | 100nF/10V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C56 |
| 1 | 10u / 50V | Motor:Capacitor_SMD__C_0805_2012Metric | C2 |
| 1 | 10uF/10V X7R | Motor:Capacitor_SMD__C_0805_2012Metric | C70 |
| 1 | 12V | Motor:Diode_SMD__D_SOD-123 | D5 |
| 1 | 12nF/50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C73 |
| 1 | 150k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R64 |
| 1 | 15A/85V FAST | Motor:Fuse_Littelfuse_448_6.10x2.69mm_GenericBody | F1 |
| 1 | 1nF/50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C77 |
| 1 | 2.2k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R5 |
| 1 | 215k / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R72 |
| 1 | 33.6k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R68 |
| 1 | 4.7nF/50V | Motor:C_0603_1608Metric_Gap0.85mm_HandSolder | C71 |
| 1 | 4.7u / 4.5A | Motor:Inductor_SMD__L_Bourns_SRN6045TA | L1 |
| 1 | 41.2k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R70 |
| 1 | 412k | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R63 |
| 1 | 49.9k / 0.1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R65 |
| 1 | 4A / 125V 延时 | Motor:Fuse_NANO2_454_6.10x2.69mm | F2 |
| 1 | 698k / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R3 |
| 1 | 953 / 1% | Motor:R_0603_1608Metric_Gap0.85mm_HandSolder | R67 |
| 1 | AP2112K-3.3TRG1 | Motor:Package_TO_SOT_SMD__SOT-23-5 | U7 |
| 1 | AP63205WU-7 | Motor:Package_TO_SOT_SMD__TSOT-23-6 | U1 |
| 1 | BZT52C12 | Motor:Diode_SMD__D_SOD-123 | D1 |
| 1 | C5-EDGE-3 / 98P | Motor:C5_EDGE_3_Socket | J14 |
| 1 | HC-08_四脚接口 | Motor:Connector_PinSocket_2.54mm__PinSocket_1x04_P2.54mm_Vertical | J15 |
| 1 | LED_GREEN | Motor:LED_0603_1608Metric_Gap0.85mm_HandSolder | D4 |
| 1 | LTC4412ES6#TRMPBF | Motor:Package_TO_SOT_SMD__TSOT-23-6 | U14 |
| 1 | MMBT3904 | Motor:Package_TO_SOT_SMD__SOT-23 | Q8 |
| 1 | MaixCAM2_图传 | Motor:Connector_JST__JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J19 |
| 1 | RUN / STOP_NC | Motor:Connector_PinHeader_2.54mm__PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | SGM2531CXPS8G/TR | Motor:SGM_PS8_SOIC8_EP2.33x3.22_HandSolder | U10 |
| 1 | SMAJ15A | Motor:Diode_SMD__D_SMA | D2 |
| 1 | SS12D10G5 | Motor:SS12D10G5_SHOUHAN_3P_P4.80mm | SW1 |
| 1 | SS34 | Motor:Diode_SMD__D_SMA | D3 |
| 1 | SWD / XH2.50 | Motor:Connector_JST__JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J8 |
| 1 | TFT_ZJY180S0800TG01 | Motor:Connector_PinSocket_2.54mm__PinSocket_1x08_P2.54mm_Vertical | J17 |
| 1 | TPS259470LRPWR | Motor:TPS25947_RPW0010A_VQFN-HR_2x2mm | U9 |
| 1 | XT60PW-M | Motor:AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J1 |
| 1 | ZDT_XS_TTL_8P | Motor:Connector_JST__JST_XH_B8B-XH-A_1x08_P2.50mm_Vertical | J23 |
| 1 | 下一项 | Motor:SW_Push_6x6x4.3mm_SMD_4Pad_Generic | SW3 |
| 1 | 启动 | Motor:SW_Push_6x6x4.3mm_SMD_4Pad_Generic | SW5 |
| 1 | 模式 | Motor:SW_Push_6x6x4.3mm_SMD_4Pad_Generic | SW2 |
| 1 | 步进_脉冲控制 | Motor:Connector_JST__JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J22 |
| 1 | 步进驱动电源 | Motor:TerminalBlock_Phoenix__TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J24 |
The 181 most common of 187 parts.

SmallCoral/c5-car
用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。

SmallCoral/c5-car
用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。

SmallCoral/c5-car
用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。

SmallCoral/c5-car
用 KiCad 10 打开 CoralC5-Expansion.kicadpro。这是 Coral-C5 的单槽扩展板,顶部 J14 接核心板,左右 J9、J8 各一组 2×24 排针,下方放 RJ45 和 microSD,右侧放 ESP32-C3-MINI-1U。100×86mm 板框为本项目暂定尺寸。

DD1SB/ARDF-TX
Date: 2026-10-15. Engineering review only; unbuilt and unenergized. Open RF80.kicadpro, schematic and native PCB in KiCad10.0.6. Three primary PCBs and the separate VHF true-AM design are unchanged.



Game-Team-SLSC/eurobot-2026-robot
The repo for firmware and hardware and docs of the 2026 Game Team's robot for CDFR Junior

gonewx/quadcuber
本目录是 A1 电子源目录。打开 quadcuber.kicadpro,包含原生可编辑原理图和四层 PCB、本地符号/封装库。本设计为单块PCB,RP2040、QSPI Flash、晶振、USB-C、驱动和电源均直接焊接在板上;A0的Pico H插装已移除。马达使用EV3裸插座。接线定义仍从 ../wiring/spec.py 导入,固件未改动,也没有把 R/L 固件描述成已支持四臂控制。

TCC-Sumo-Telemetria/Eletronica_Sumo_Telemetria
Projetos eletrônicos relacionados ao trabalho de conclusão de curso "SISTEMA DE TELEMETRIA PARA A AVALIAÇÃO DE DESEMPENHO DE UM ROBÔ DE MEGA SUMÔ AUTÔNOMO".


187 parts, built around the SN74LV1T125DBVR-TP, SN74LVC2G125DCTR-JSM, SN74LVC2G17DCKR and LTC4412ES6#TRMPBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the SmallCoral/c5-car repository on GitHub, at the commit this page was made from: the board is Hardware/stm32c5a3/Hardware/CoralC5-Motor/docs/baseline-2026-11-07-m27/CoralC5-Motor.kicad_pcb and its schematic Hardware/stm32c5a3/Hardware/CoralC5-Core/.history/02_Power_USB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask SmallCoral before reusing the design.