Skip to the content
2 layers247.7 × 95.3 mmWTLBetter62, the printed circuit board in 3D

WTLBetter62

Sat1l/wtl622
Size
247.7 × 95.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
153
Nets
107
Pads
672
Tracks, vias
764, 108
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
26 Dec 2021
Updated
27 Dec 2023

Overview

WTLBetter62 is an open-source printed circuit board by Sat1l, from the Sat1l/wtl62 repository on GitHub. It is a 2-layer board of 247.7 × 95.3 mm with 153 parts on 107 nets, routed with 764 tracks and 108 vias.

It is built around the ATMEGA32U4-AU and CSTNE16M0V530000R0. Its parts include 62 diodes, 7 capacitors, 6 resistors, 1 IC and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

wtl62

Hardware disclaimer

The folder structure is fucked up and probably wont be fixed as i see no reason for this. Top case part (plate) is located in the bottom case part folder, and this one is located in the general pcb folder. Yeah. There's also Willing To Live Better 62 inside, but this one proly wont' see a light of day as there prolly aint no interest in this design. Have fun.

firmware use guide

clone wtl62 folder to qmk_firmware/keyboards

Compiling

qmk compile -kb WTL62 -km keymap

  • replace keymap with keymap you would like to compile. This repo contains only default keymap
Flashing default .hex file

QMK Toolbox is the easiest way to do this. Short pins gnd and rst on yours MCU to reset

Using Vial
  1. Flash wtl62_via.hex file to the keyboard
  2. Open Vial
  3. Go to File>Sideload VIA JSON...
  4. Select via.json file
  5. Voila! Now you can configure wtl62 using Vial

Parts

153
QtyValueFootprintReferences
62MX-NoLEDkbd:CherryMX_HotswapMX1, MX2, MX10, MX11, MX12, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX21, MX22, MX23 +46
62sod-123kbd:D3_SMD_v2D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +46
6Val**kbd:M2_HOLE_v2Ref**, Ref**, Ref**, Ref**, Ref**, Ref**
30.1ufCapacitor_SMD:C_0805_2012MetricC4, C5, C6
210kResistor_SMD:R_0805_2012MetricR1, R4
222Resistor_SMD:R_0805_2012MetricR2, R3
222pFCapacitor_SMD:C_0805_2012MetricC1, C2
25.1kResistor_SMD:R_0805_2012MetricR5, R6
110ufCapacitor_SMD:C_0805_2012MetricC7
11ufCapacitor_SMD:C_0805_2012MetricC3
1500mAFuse:Fuse_1206_3216MetricF1
1ATmega32U4-APackage_QFP:TQFP-44_10x10mm_P0.8mmU1
1CSTNE16M0V530000R0CSTNE16M0V530000R0:OSC_CSTNE16M0V530000R0Y1
1USB_C_Receptacle_USB2.0nrfmicro:easyeda_C168688J1

The 147 most common of 153 parts.

More from Sat1l/wtl62

1
  • 2 layers247.6 × 96.8 mmWTL62, the printed circuit board in 3D

    WTL62

    Sat1l/wtl62

    138 parts2

Similar boards

  • 4 layers50 × 42 mmCawDrive, the printed circuit board in 3D

    CawDrive

    noxrick91/caw-drive

    三相直流无刷电机驱动器硬件

    112 parts108GPL-3.0
  • 2 layers373.2 × 131.8 mmNt980, the printed circuit board in 3D

    Nt980

    evyd13/nt-series

    Replacement PCBs for the FC660m, FC750r and FC980m.

    242 parts56CC-BY-SA-4.0
  • 4 layers29.3 × 187.1 mmLeft Frame, the printed circuit board in 3D

    Left Frame

    FlightDeckDIY/G1000-NXi-Mega

    Welcome to the G1000 NXi Mega project! This repository contains the schematic and PCB design files for a custom-built G1000 avionics panel, designed specifically for use with flight simulators like Microsoft Flight…

    127 parts14
  • 2 layers35 × 54 mmEvoluent, the printed circuit board in 3D

    Evoluent

    mon/evoluent_better_pcb

    PCBs using better sensor for Evoluent VerticalMouse products

    30 parts11MIT
  • 2 layers115.7 × 107.6 mmMotor flasher, the printed circuit board in 3D

    Motor flasher

    kscalelabs/motor-flasher

    Motor flasher repository

    114 parts2
  • 2 layers40 × 40 mmCurcuitV4, the printed circuit board in 3D

    CurcuitV4

    banbatakumi/BLDC

    97 parts1
  • 2 layers68.6 × 53.3 mmArduino Mega 2560, the printed circuit board in 3D

    Arduino Mega 2560

    ded811/Mega-Uno-2560

    An Arduino-compatible ATmega2560 development board in the Arduino Uno form factor

    62 parts1

Questions

How big is the WTLBetter62 PCB?

It measures 247.7 × 95.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the WTLBetter62 use?

153 parts, built around the ATMEGA32U4-AU and CSTNE16M0V530000R0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WTLBetter62 KiCad files?

From the Sat1l/wtl62 repository on GitHub, at the commit this page was made from: the board is WTL-62 - KiCad/WTLBetter62/WTLBetter62.kicad_pcb and its schematic WTL-62 - KiCad/WTL62.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the WTLBetter62 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Sat1l before reusing the design.