
ATMEGA32U4-AU
Microchip TechnologyExtended
-40℃~+85℃ 10bit 16MHz 1KB 2.5KB 2.7V~5.5V 26 32KB 8 Bit AVR Built-in FLASH QFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHS
- Part id
- microchip/ATMEGA32U4-AU
- Category
- Microcontrollers (MCU, MPU, SOC)
- Package
- QFP-44(10x10)
- Pins
- 44
- In stock
- 2,735 at JLCPCB (C44854)
- Used on
- 562 open-source boards
Overview
The ATMEGA32U4-AU is a microcontroller made by Microchip Technology in a QFP-44(10x10) package with 44 pins. -40℃~+85℃ 10bit 16MHz 1KB 2.5KB 2.7V~5.5V 26 32KB 8 Bit AVR Built-in FLASH QFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its KiCad symbol (MCU_Microchip_ATmega:ATmega32U4-A, from KiCad's library) and its footprint (generated:QFP-44_10x10mm_P0.8mm, from generated from its package), ready for a KiCad board. 2,735 are in stock at JLCPCB (part C44854). 562 open-source boards in 450 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
9- Supply, least
- 2.7 V · VCC, recommended operating min · p. 378
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 378
- Supply, absolute maximum
- 6 V · VCC, absolute maximum · p. 378
- Works from
- -40 °C · Operating temperature min · p. 378
- Works up to
- 85 °C · Operating temperature max · p. 378
- A pin gives at most
- 40 mA · DC current per I/O pin, absolute maximum · p. 378
- Takes working
- 10 mA · VCC, active at 8 MHz and 5 V, typical · p. 379
- Takes at most
- 15 mA · VCC, active at 8 MHz and 5 V, max · p. 379
- Takes asleep
- 1 µA · Power-down, WDT disabled, VCC = 3 V, regulator disabled, typical · p. 379
What it is and has
31- Core
- AVR 8-bit, Advanced RISC Architecture · p. 1
- Performance
- Up to 16 MIPS at 16 MHz · p. 1
- Working registers
- 32 x 8 · p. 1
- Flash memory
- 32K Bytes, In-System Self-Programmable · p. 1
- SRAM
- 2.5K Bytes · p. 1
- EEPROM
- 1K Bytes · p. 1
- Write/Erase endurance
- 10,000 Flash cycles; 100,000 EEPROM cycles · p. 1
- JTAG
- IEEE 1149.1 compliant · p. 1
- USB
- USB 2.0 Full-speed/Low Speed Device Module · p. 1
- USB data rates
- 12 Mbit/s and 1.5 Mbit/s · p. 1
- USB endpoint memory
- 832 bytes independent DPRAM · p. 1
- PLL
- 32 to 96 MHz for USB and High Speed Timer · p. 1
- 8-bit Timer/Counter
- 1, separate prescaler and compare mode · p. 1
- 16-bit Timer/Counter
- 2, separate prescaler, compare and capture mode · p. 1
- High-Speed Timer/Counter
- 1, 10-bit, PLL at 64 MHz, compare mode · p. 1
- 8-bit PWM
- 4 channels · p. 1
- Programmable PWM
- 4 channels, 2 to 16 bits · p. 1
- ADC
- 10-bit, 12 channels, differential channels with programmable gain · p. 1
- USART
- Programmable, hardware flow control · p. 1
- SPI
- Master/Slave · p. 1
- Core
- High Performance, Low Power AVR 8-Bit Microcontroller · p. 1
- Instruction set
- 135 instructions; most execute in one clock cycle · p. 1
- Throughput
- Up to 16 MIPS at 16 MHz · p. 1
- Multiplier
- On-chip, 2-cycle · p. 1
- Flash memory
- 32K Bytes, in-system self-programmable · p. 1
- Write/erase endurance
- 10,000 Flash cycles; 100,000 EEPROM cycles · p. 1
- Data retention
- 20 years at 85°C; 100 years at 25°C · p. 1
- Boot code
- Optional boot code section with independent lock bits · p. 1
- Bootloader
- Preprogrammed default USB bootloader · p. 1
- Software security
- Programming lock · p. 1
- Debug
- Extensive on-chip debug support · p. 1
Around it
2- cap 1µF±20%
- between UCAP and GND; USB regulator capacitor; electrical-characteristic test condition · p. 379
- res 22±5% Ω
- between USB data pin and USB data bus; External USB series resistor · p. 379
Specifications
132| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Operating Temperature | min -40 · max 85 °C | 378 | |
| Storage Temperature | min -65 · max 150 °C | 378 | |
| Voltage on any Pin except RESET and VBUS with respect to Ground(8) | min -0.5 V | 378 | |
| Voltage on RESET with respect to Ground | min -0.5 · max 13 V | 378 | |
| Voltage on VBUS with respect to Ground | min -0.5 · max 6 V | 378 | |
| Maximum Operating Voltage | max 6 V | 378 | |
| DC Current per I/O Pin | max 40 mA | 378 | |
| DC Current VCC and GND Pins | max 200 mA | 378 | |
| Input Low Voltage,Except XTAL1 and Reset pin VIL | VCC = 2.7V - 5.5V | min -0.5 V | 378 |
| Input Low Voltage, XTAL1 pin VIL1 | VCC = 2.7V - 5.5V | min -0.5 V | 378 |
| Input Low Voltage, RESET pin VIL2 | VCC = 2.7V - 5.5V | min -0.5 V | 378 |
| Output Low Voltage(3), VOL | IOL = 10mA, VCC = 5V | max 0.7 V | 378 |
| Output Low Voltage(3), VOL | IOL = 5mA, VCC = 3V | max 0.5 V | 378 |
| Output High Voltage(4), VOH | IOH = -10mA, VCC = 5V | min 4.2 V | 378 |
| Output High Voltage(4), VOH | IOH = -5mA, VCC = 3V | min 2.3 V | 378 |
| Input Leakage Current I/O Pin IIL | VCC = 5.5V, pin low (absolute value) | max 1 uA | 378 |
| Input Leakage Current I/O Pin IIH | VCC = 5.5V, pin high (absolute value) | max 1 uA | 378 |
| Reset Pull-up Resistor RRST | min 30 · max 60 kΩ | 378 | |
| I/O Pin Pull-up Resistor RPU | min 20 · max 50 kΩ | 378 | |
| Power Supply Current(6) ICC | Active 4MHz, VCC = 3V; ATmega32U4 | max 5 mA | 379 |
| Power Supply Current(6) ICC | Active 8MHz, VCC = 5V; ATmega32U4 | typ 10 · max 15 mA | 379 |
| Power Supply Current(6) ICC | Idle 4MHz, VCC = 3V; ATmega32U4 | max 2 mA | 379 |
| Power Supply Current(6) ICC | Idle 8MHz, VCC = 5V; ATmega32U4 | max 6 mA | 379 |
| Power-down mode ICC | WDT enabled, VCC = 3V, Regulator Disabled | max 12 uA | 379 |
| Power-down mode ICC | WDT disabled, VCC = 3V,Regulator Disabled | typ 1 · max 5 uA | 379 |
| Analog Comparator Input Offset Voltage VACIO | VCC = 5V, Vin = VCC/2 | max 40 mV | 379 |
| Analog Comparator Input Leakage Current IACLK | VCC = 5V, Vin = VCC/2 | min -50 · max 50 nA | 379 |
| Analog Comparator Propagation Delay tACID | VCC = 2.7V | typ 750 ns | 379 |
| Analog Comparator Propagation Delay tACID | VCC = 4.0V | typ 500 ns | 379 |
| Regulator Output Voltage Vreg | CUCAP=1uF±20%, UVcc 4.0V, I≤80mA(7), or UVcc 3.4V, I≤55mA(7) | min 3 · typ 3.3 · max 3.6 V | 379 |
| Oscillator Frequency 1/tCLCL | VCC=1.8-5.5V | min 0 · max 2 MHz | 380 |
| Oscillator Frequency 1/tCLCL | VCC=2.7-5.5V | min 0 · max 8 MHz | 380 |
| Oscillator Frequency 1/tCLCL | VCC=4.5-5.5V | min 0 · max 16 MHz | 380 |
| Clock Period tCLCL | VCC=1.8-5.5V | min 500 ns | 380 |
| Clock Period tCLCL | VCC=2.7-5.5V | min 125 ns | 380 |
| Clock Period tCLCL | VCC=4.5-5.5V | min 62.5 ns | 380 |
| High Time tCHCX | VCC=1.8-5.5V | min 200 ns | 380 |
| High Time tCHCX | VCC=2.7-5.5V | min 50 ns | 380 |
| High Time tCHCX | VCC=4.5-5.5V | min 25 ns | 380 |
| Low Time tCLCX | VCC=1.8-5.5V | min 200 ns | 380 |
| Low Time tCLCX | VCC=2.7-5.5V | min 50 ns | 380 |
| Low Time tCLCX | VCC=4.5-5.5V | min 25 ns | 380 |
| Rise Time tCLCH | VCC=1.8-5.5V | max 2 us | 380 |
| Rise Time tCLCH | VCC=2.7-5.5V | max 1.6 us | 380 |
| Rise Time tCLCH | VCC=4.5-5.5V | max 0.5 us | 380 |
| Fall Time tCHCL | VCC=1.8-5.5V | max 2 us | 380 |
| Fall Time tCHCL | VCC=2.7-5.5V | max 1.6 us | 380 |
| Fall Time tCHCL | VCC=4.5-5.5V | max 0.5 us | 380 |
| Change in period from one clock cycle to the next ΔtCLCL | VCC=1.8-5.5V | max 2 % | 380 |
| Change in period from one clock cycle to the next ΔtCLCL | VCC=2.7-5.5V | max 2 % | 380 |
| Change in period from one clock cycle to the next ΔtCLCL | VCC=4.5-5.5V | max 2 % | 380 |
| Input Low-voltage VIL | min -0.5 V | 381 | |
| Output Low-voltage VOL | 3 mA sink current; characterized and not 100% tested | min 0 · max 0.4 V | 381 |
| Rise Time for both SDA and SCL tr | Cb = capacitance of one bus line in pF; minimum required only for fSCL > 100 kHz; characterized and not 100% tested | max 300 ns | 381 |
| Output Fall Time from VIHmin to VILmax tof | 10 pF < Cb < 400 pF; minimum required only for fSCL > 100 kHz; characterized and not 100% tested | max 250 ns | 381 |
| Spikes Suppressed by Input Filter tSP | Required only for fSCL > 100 kHz; characterized and not 100% tested | min 0 · max 50 ns | 381 |
| Input Current each I/O Pin Ii | 0.1VCC < Vi < 0.9VCC | min -10 · max 10 uA | 381 |
| Capacitance for each I/O Pin Ci | Characterized and not 100% tested | max 10 pF | 381 |
| SCL Clock Frequency fSCL | fCK > max(16fSCL, 250kHz); fCK = CPU clock frequency | min 0 · max 400 kHz | 381 |
| Hold Time (repeated) START Condition tHD;STA | fSCL ≤ 100 kHz | min 4 us | 381 |
| Hold Time (repeated) START Condition tHD;STA | fSCL > 100 kHz | min 0.6 us | 381 |
| Low Period of the SCL Clock tLOW | fSCL ≤ 100 kHz; see note 6 | min 4.7 us | 381 |
| Low Period of the SCL Clock tLOW | fSCL > 100 kHz; see note 7 | min 1.3 us | 381 |
| High period of the SCL clock tHIGH | fSCL ≤ 100 kHz | min 4 us | 382 |
| High period of the SCL clock tHIGH | fSCL > 100 kHz | min 0.6 us | 382 |
| Set-up time for a repeated START condition tSU;STA | fSCL ≤ 100 kHz | min 4.7 us | 382 |
| Set-up time for a repeated START condition tSU;STA | fSCL > 100 kHz | min 0.6 us | 382 |
| Data hold time tHD;DAT | fSCL ≤ 100 kHz | min 0 · max 3.45 us | 382 |
| Data hold time tHD;DAT | fSCL > 100 kHz | min 0 · max 0.9 us | 382 |
| Data setup time tSU;DAT | fSCL ≤ 100 kHz | min 250 ns | 382 |
| Data setup time tSU;DAT | fSCL > 100 kHz | min 100 ns | 382 |
| Setup time for STOP condition tSU;STO | fSCL ≤ 100 kHz | min 4 us | 382 |
| Setup time for STOP condition tSU;STO | fSCL > 100 kHz | min 0.6 us | 382 |
| Bus free time between a STOP and START condition tBUF | fSCL ≤ 100 kHz | min 4.7 us | 382 |
| Bus free time between a STOP and START condition tBUF | fSCL > 100 kHz | min 1.3 us | 382 |
| Setup | Master | typ 10 ns | 383 |
| Hold | Master | typ 10 ns | 383 |
| SCK to out | Master | typ 10 ns | 383 |
| SCK to out high | Master | typ 10 ns | 383 |
| SS low to out | Slave | typ 15 ns | 383 |
| Setup | Slave | min 10 ns | 383 |
| SCK to out | Slave | typ 15 ns | 383 |
| SCK to SS high | Slave | min 20 ns | 383 |
| SS high to tri-state | Slave | typ 10 ns | 383 |
| SS low to SCK | Slave | min 20 ns | 383 |
| HWB low Setup before Reset High tSHRH | min 0 | 384 | |
| Resolution | Single Ended Conversion | typ 10 Bits | 384 |
| Resolution | Differential conversion, gain = 1x/10x/40x | typ 8 Bits | 384 |
| Resolution | Differential conversion, gain = 200x | typ 8 Bits | 384 |
| Absolute accuracy TUE | VREF = 4V, VCC = 4V, ADC clock = 200 kHz | typ 2 · max 3 LSB | 384 |
| Absolute accuracy TUE | Gain = 1x/10x/40x, VREF = 4V, VCC = 5V, ADC clock = 200 kHz | typ 2 · max 3 LSB | 384 |
| Absolute accuracy TUE | Gain = 200x, VREF = 4V, VCC = 5V, ADC clock = 200 kHz | typ 2 · max 4 LSB | 384 |
| Power-on Reset Threshold Voltage (rising) VPOT | typ 1.4 · max 2.3 V | 50 | |
| Power-on Reset Threshold Voltage (falling) VPOT | typ 1.3 · max 2.3 V | 50 | |
| VCC Start Voltage to ensure internal Power-on Reset signal VPOR | min -0.1 · max 0.1 V | 50 | |
| VCC Rise Rate to ensure internal Power_on Reset signal VCCRR | min 0.3 V/ms | 50 | |
| Minimum pulse width on RESET Pin tRST | 5V, 25°C | typ 400 ns | 50 |
| Bandgap reference voltage VBG | TBD; values are guidelines only, actual values are TBD | typ 1.1 V | 55 |
| Bandgap reference start-up time tBG | TBD; values are guidelines only, actual values are TBD | typ 40 · max 70 us | 55 |
| Bandgap reference current consumption IBG | TBD; values are guidelines only, actual values are TBD | typ 10 uA | 55 |
| Input Low Voltage,Except XTAL1 and Reset pin VIL | TA = -40°C to 85°C; VCC = 2.7V - 5.5V; LVTTL | min -0.5 V | 378 |
| Input Low Voltage, XTAL1 pin VIL1 | TA = -40°C to 85°C; VCC = 2.7V - 5.5V | min -0.5 V | 378 |
| Input Low Voltage, RESET pin VIL2 | TA = -40°C to 85°C; VCC = 2.7V - 5.5V | min -0.5 V | 378 |
| Output Low Voltage(3), VOL | TA = -40°C to 85°C; IOL = 10mA, VCC = 5V | max 0.7 V | 378 |
| Output Low Voltage(3), VOL | TA = -40°C to 85°C; IOL = 5mA, VCC = 3V | max 0.5 V | 378 |
| Output High Voltage(4), VOH | TA = -40°C to 85°C; IOH = -10mA, VCC = 5V | min 4.2 V | 378 |
| Output High Voltage(4), VOH | TA = -40°C to 85°C; IOH = -5mA, VCC = 3V | min 2.3 V | 378 |
| Input Leakage Current I/O Pin IIL | TA = -40°C to 85°C; VCC = 5.5V, pin low (absolute value) | max 1 uA | 378 |
| Input Leakage Current I/O Pin IIH | TA = -40°C to 85°C; VCC = 5.5V, pin high (absolute value) | max 1 uA | 378 |
| Reset Pull-up Resistor RRST | TA = -40°C to 85°C; VCC = 2.7V to 5.5V | min 30 · max 60 kΩ | 378 |
| I/O Pin Pull-up Resistor RPU | TA = -40°C to 85°C; VCC = 2.7V to 5.5V | min 20 · max 50 kΩ | 378 |
| Power Supply Current(6) ICC | ATmega32U4; TA = -40°C to 85°C; Active 4MHz, VCC = 3V; PRR1 = 0x00 | max 5 mA | 379 |
| Power Supply Current(6) ICC | ATmega32U4; TA = -40°C to 85°C; Active 8MHz, VCC = 5V; PRR1 = 0x00 | typ 10 · max 15 mA | 379 |
| Power Supply Current(6) ICC | ATmega32U4; TA = -40°C to 85°C; Idle 4MHz, VCC = 3V; PRR1 = 0x00 | max 2 mA | 379 |
| Power Supply Current(6) ICC | ATmega32U4; TA = -40°C to 85°C; Idle 8MHz, VCC = 5V; PRR1 = 0x00 | max 6 mA | 379 |
| Power-down mode ICC | TA = -40°C to 85°C; WDT enabled, VCC = 3V, Regulator Disabled; PRR1 = 0x00 | max 12 uA | 379 |
| Power-down mode ICC | TA = -40°C to 85°C; WDT disabled, VCC = 3V, Regulator Disabled; PRR1 = 0x00 | typ 1 · max 5 uA | 379 |
| Analog Comparator Input Offset Voltage VACIO | TA = -40°C to 85°C; VCC = 5V; Vin = VCC/2 | max 40 mV | 379 |
| Analog Comparator Input Leakage Current IACLK | TA = -40°C to 85°C; VCC = 5V; Vin = VCC/2 | min -50 · max 50 nA | 379 |
| Analog Comparator Propagation Delay tACID | TA = -40°C to 85°C; VCC = 2.7V | typ 750 ns | 379 |
| Analog Comparator Propagation Delay tACID | TA = -40°C to 85°C; VCC = 4.0V | typ 500 ns | 379 |
| Regulator Output Voltage Vreg | TA = -40°C to 85°C; CUCAP=1uF±20%; UVcc 4.0V, I≤80mA(7), or UVcc 3.4V, I≤55mA(7) | min 3 · typ 3.3 · max 3.6 V | 379 |
| Setup | Master; timing parameter 4 | typ 10 ns | 383 |
| Hold | Master; timing parameter 5 | typ 10 ns | 383 |
| SCK to out | Master; timing parameter 7 | typ 10 ns | 383 |
| SCK to out high | Master; timing parameter 8 | typ 10 ns | 383 |
| SS low to out | Slave; timing parameter 9 | typ 15 ns | 383 |
| Setup | Slave; timing parameter 13 | min 10 ns | 383 |
| SCK to out | Slave; timing parameter 15 | typ 15 ns | 383 |
| SCK to SS high | Slave; timing parameter 16 | min 20 ns | 383 |
| SS high to tri-state | Slave; timing parameter 17 | typ 10 ns | 383 |
| SS low to SCK | Slave; timing parameter 18 | min 20 ns | 383 |
- 2 layers243.2 × 106 mm

- 2 layers228.4 × 85 mm

LeChiffre
tominabox1/Le-Chiffre-Keyboard
Great thanks goes to Jake at P3D for really making the case amazing and open sourcing his work. Check him out at P3Dstore.com
105 parts183GPL-3.0 - 2 layers228.6 × 76.8 mm

Schwann Rev0.5b
The-Royal/The_Royal_Open-Source-Projects
A Master Repository For All things Royal Made
127 parts159MIT - 2 layers30 × 65 mm

Keyboard mcu
dpapavas/lagrange-keyboard
A configurable, handwired, ergonomic keyboard
26 parts137AGPL-3.0 - 2 layers88.4 × 80 mm

LHS Controller PCB
dmcke5/ZenDeck
This is the second revision of my Mini PC based handheld Gaming PC! It is designed for a Beelink SER 5 Mini PC but could be adapted to other systems by changing the mounting brackets and outlet plate.
76 parts133CERN-OHL-S-2.0 - 2 layers259.5 × 89.1 mm

- 2 layers99.1 × 99.1 mm

Power supply panelized
thebiguno/microcontroller-projects
A home for a bunch of microcontroller projects which don't warrant their own repos.
223 parts75 - 2 layers323.9 × 95.1 mm

UnSplit
swiftrax/UnSplit
Ergo 40% mechanical keyboard with all components on the top with diodes arranged in an array
110 parts68GPL-2.0
Parts like it
8ATMEGA32A-AU
TQFP-44(10x10)-40℃~+85℃ 10bit 16MHz 1KB 2.7V~5.5V 2KB 32 32KB 8 Bit AVR Built-in FLASH TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)STC89C52RC-40I
LQFP-44(10x10)3.3V~5.5V 39 51 Family 8KB FLASH LQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTCMicrocontrollers (MCU/MPU/SOC)STM8S105S4T6C
LQFP-44(10x10)-40℃~+85℃ 10bit 16KB 16MHz 1KB 2.95V~5.5V 2KB 34 8 Bit Built-in FLASH STM8 LQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)PIC16F1939-I/PT
TQFP-44(10x10)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 256Byte 28KB 32MHz 36 8 Bit Built-in FLASH PIC TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)ATMEGA16A-AU
TQFP-44(10x10)-40℃~+85℃ 10bit 16KB 16MHz 1KB 2.7V~5.5V 32 512Byte 8 Bit AVR Built-in FLASH TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)STC8A8K64D4-45I-LQFP44
LQFP-44(10x10)51 Family 64KB FLASH LQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTC MicroMicrocontrollers (MCU/MPU/SOC)PIC16F1937-I/PT
TQFP-44(10x10)-40℃~+85℃ 1.8V~5.5V 10bit 14KB 256Byte 32MHz 36 512Byte 8 Bit Built-in FLASH PIC TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)R5F100FEAFP#10
TQFP-44(10x10)-40℃~+85℃ 1.6V~5.5V 10bit 16 Bit 31 32MHz 4KB 4KB 64KB Built-in FLASH RL78 TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSRenesas ElectronicsMicrocontrollers (MCU/MPU/SOC)
Questions
Is there a KiCad symbol and footprint for the ATMEGA32U4-AU?
Yes. The symbol is MCU_Microchip_ATmega:ATmega32U4-A and the footprint generated:QFP-44_10x10mm_P0.8mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the ATMEGA32U4-AU?
QFP-44(10x10), with 44 pins. Its footprint is drawn on this page.
Where is the ATMEGA32U4-AU datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the ATMEGA32U4-AU?
JLCPCB lists it as part C44854, with 2,735 in stock; the sellers' links on this page open their listings.
What can replace the ATMEGA32U4-AU?
Parts like it in the library: the ATMEGA32A-AU by Microchip Technology, the STC89C52RC-40I by STC, the STM8S105S4T6C by STMicroelectronics and the PIC16F1939-I/PT by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the ATMEGA32U4-AU?
562 boards in 450 repositories on GitHub; the most starred are listed on this page, with their KiCad files.