

PCB milli
Portable and low cost milliommeter with good performances
- Size
- 61.6 × 48.9 mm
- Copper layers
- 2
- Thickness
- 1.58 mm
- Parts
- 24
- Nets
- 10
- Pads
- 54
- Tracks, vias
- 51, 0
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 22 May 2025
- Updated
- 22 May 2025
Overview
PCB milli is an open-source printed circuit board by Pronoe, from the Pronoe/millihom-meter repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 61.6 × 48.9 mm with 24 parts on 10 nets, routed with 51 tracks and 0 vias.
It is built around the TLC272CD and BC548. Its parts include 5 resistors, 3 capacitors, 2 ICs, 1 diode and 1 transistor.
Main components
2README
README.mdmilliohm-meter
Portable and low cost milliommeter with good performances
Introduction
When you have to debug electronic systems or find failure on an electronic board or electrical system, you frequently need to locate short circuits. Common multimeters are generally limited down to 1 ohm in their measurement and this is not sufficient for efficient characterization and localization of a short circuit. Below the 1 ohm domain, a milliohmmemeter is the required instrument but Industrial miiliohmmeters are expensive so I decided to build my own device.
General design
I had viewed a good publication for a DIY milliohmmeter from the "Electro-bidouilleur" YouTube channel. The Elektor magazine sells also a add-on device for multimeters. However this projects suffers several drawbacks:
- need a separate multimeter for the measurement
- provides no protection against excessive voltage on the device under test
- do not use 4 wires measurement for better accuracy The main characteristics of my design are:
- use of a INA199 from Texas Instrument for the measurement o this is a Voltage-Output, Current-Shunt Monitor which need no additional component o provides very low offset voltage and very low drift o high accuracy gain
- current source of 10.6 mA build with a ½ TLC272 which is a precision dual operational amplifier
- voltage limiter with a BC548 transistor
- use of and Arduino Uno board for: o output voltage measurement, o resistance computation from voltage measurement o initial zero compensation o full range calibration
- use of a 2 lines x 16 characters LCD display shield for user interface
- use of a a 1200 mAh LiPo battery combined with a step up converter/ battery charger for portable operation
- use of a "Kelvin" 4 wires cable for device connection
see detailed information in technical files
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H8, H9, H10, H11 |
| 2 | 100n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C2 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R5 |
| 2 | 470 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R4 |
| 1 | 100 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 47u | Capacitor_THT:CP_Axial_L11.0mm_D6.0mm_P18.00mm_Horizontal | C3 |
| 1 | BA315 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | BC548 | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | GND | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H2 |
| 1 | IC+ | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H6 |
| 1 | IC- | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H5 |
| 1 | IN+ | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H3 |
| 1 | IN- | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H4 |
| 1 | INA199xxDCK | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U1 |
| 1 | Probe | TestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP1 |
| 1 | TLC272 | Package_DIP:DIP-8_W7.62mm | U2 |
| 1 | VCC | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H1 |
| 1 | VOUT | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_Relief | H7 |
Similar boards
- 2 layers85 × 61 mm

- 2 layers200 × 87.8 mm

- 2 layers52.3 × 51.8 mm

- 2 layers92.5 × 99.7 mm

Opamp vu meter
CASE-Association/christmas-cards
All CASE christmas cards over the years
48 parts3GPL-3.0 - 2 layers50 × 40.9 mm

GR ATTiny LFO
GadgetReboot/ATTiny_LFO
Dual low frequency oscillators using ATTiny and MCP4725 DACs
36 parts3 - 2 layers56.5 × 74 mm

Ascom flat panel
letelescope/ascom-flat-panel
Open source ASCOM and INDI driven automated flat panel for astrophotography
17 parts2MIT - 2 layers43.5 × 46.9 mm

Schaltplan Ultraschallsensor
Tinkerforge/distance-us-v2-bricklet-techniker
This repository contains the firmware source code and the hardware design files. The documentation generator configs can be found at https://github.com/Tinkerforge/generators
54 parts2 - 2 layers85 × 56.5 mm

Questions
How big is the PCB milli PCB?
It measures 61.6 × 48.9 mm and has 2 copper layers, 1.58 mm thick.
What parts does the PCB milli use?
24 parts, built around the TLC272CD and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PCB milli KiCad files?
From the Pronoe/millihom-meter repository on GitHub, at the commit this page was made from: the board is pcb_Kicad/PCB_milli.kicad_pcb and its schematic pcb_Kicad/PCB_milli.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PCB milli design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).