
DSP Regulator HAT RevB
Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

3 channel bench supply with current and voltage plotting
DSP Regulator RevC is an open-source printed circuit board by Phil-CIA, from the Phil-CIA/Development-Station-Power-Supply repository on GitHub. It is a 2-layer board of 100 × 125 mm with 235 parts on 145 nets.
It is built around the LMV358IDR, LM2596S-ADJ and AW9523BTQR, with the PSMN5R2-60YLX, 1SMA4742A and TC33X-2-103E among its other parts. Its parts include 100 resistors, 53 capacitors, 20 diodes, 16 ICs and 12 transistors. It belongs with the power boards of this library.
Integrated hardware and firmware repository for the development-station bench supply, its control electronics, front-panel display path, and supporting boards.
This is the active working repo for the full bench-supply platform, not just a single firmware target. It currently includes:
The project has shifted to a bring-up-first path.
Recent progress:
Current plan:
Current power-hardware status:
My_Edits schematic must be preserved and reviewed; this worktree does not contain it and the repository's partial starter is not a substitute. Firmware pin alignment, electrical/footprint qualification, PCB/DRC, and bench validation remain open under #126; existing-indicator policy is #125. See docs/HAT_CONTROLLER_EVALUATION.md for the reconciliation and historical review boundary. No fabrication or hardware validation is claimed.docs/DEV_STATION_HANDOFF_2026-08-14.md for the active restart state.Immediate firmware priority (2026-10-24): The next controller work is the
Rev-D STM32F405 transition. Do not spend bench time validating the compact F103
profile or continue optimizing F103 flash usage for future features. The F405
build already enables the full bring-up command set; its existing build is not
evidence of hardware compatibility or bench validation. Reconcile firmware
against the actual Rev-D hardware and re-verify behavior when that hardware is
available. See docs/FIRMWARE_DEVELOPMENT_PLAN.md and issue #126.
DSP-Regulator-RevB: Ready for order
DSP-Regulator-HAT-RevB: Ready for order
These Rev-B files remain the built/bench baseline. Active redesign work now lives in the corresponding Rev-C project folders; do not release Rev-C fabrication outputs until its tracker gates are closed.
Current firmware work in this repo includes:
The active CrowPanel UI plan adapts FNIRSI DPS-150 / IPS3608 styling to fixed +5V/+3.3V rails with editable current limits and shared output control. It includes the issue/PR sequence and VS Code Copilot session prompts; definitive CV/CC indication remains gated on hardware validation.
python scripts/datasheet.py find <part> before fetching| Qty | Value | Footprint | References |
|---|---|---|---|
| 26 | 100nF | PCM_JLCPCB:C_0805 | C1, C3, C11, C12, C15, C16, C24, C31, C33, C34, C35, C36, C39, C40, C41, C43 +10 |
| 19 | 10Ω | PCM_JLCPCB:R_0805 | R4, R8, R12, R15, R17, R20, R23, R34, R38, R40, R41, R46, R51, R59, R60, R75 +3 |
| 16 | 100kΩ | PCM_JLCPCB:R_0805 | R6, R9, R21, R22, R26, R27, R36, R48, R49, R53, R55, R78, R79, R88, R97, R100 |
| 16 | 10kΩ | PCM_JLCPCB:R_0805 | R14, R39, R42, R43, R58, R62, R63, R70, R71, R72, R81, R83, R84, R89, R90, R91 |
| 9 | 1kΩ | PCM_JLCPCB:R_0805 | R2, R5, R28, R33, R56, R57, R76, R80, R95 |
| 8 | 510kΩ | PCM_JLCPCB:R_0805 | R66, R67, R73, R74, R86, R87, R93, R94 |
| 8 | PSMN5R2-60YL | Package_TO_SOT_SMD:LFPAK56 | Q1, Q2, Q4, Q5, Q7, Q8, Q10, Q11 |
| 6 | 100Ω | PCM_JLCPCB:R_0805 | R1, R10, R18, R25, R44, R52 |
| 6 | TestPoint_Small | Connector_PinHeader_1.00mm:PinHeader_1x01_P1.00mm_Vertical | TP4, TP5, TP6, TP7, TP8, TP9 |
| 4 | 100nF | Capacitor_SMD:C_0805_2012Metric | C5, C18, C20, C38 |
| 4 | 10uF | PCM_JLCPCB:C_0805 | C7, C10, C21, C23 |
| 4 | 1SMA4742A | PCM_JLCPCB:D_DO-214AC(SMA) | D2, D6, D9, D13 |
| 4 | 1nF | PCM_JLCPCB:C_0805 | C27, C37, C42, C50 |
| 4 | 3296W-1-103LF | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | POT1, POT2, POT3, POT4 |
| 4 | 390kΩ | PCM_JLCPCB:R_0805 | R77, R85, R96, R99 |
| 4 | BSS138 | PCM_JLCPCB:Q_SOT-23 | Q3, Q6, Q9, Q12 |
| 4 | LM74502DDFR | Package_TO_SOT_SMD:TSOT-23-8 | U9, U14, U15, U16 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | 0Ω | PCM_JLCPCB:R_1206 | R11, R35, R68 |
| 3 | 1935161 | digikey-footprints:Terminal_Block_D1.3mm_P5mm | J1, J2, J4 |
| 3 | 270Ω | PCM_JLCPCB:R_0805 | R16, R47, R54 |
| 3 | 330uF 25v | Capacitor_SMD:CP_Elec_10x10.5 | C8, C19, C32 |
| 3 | 33uh | Inductor_SMD:L_Sunlord_MWSA1003S | L2, L3, L5 |
| 3 | LM2596S-ADJ | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U2, U4, U8 |
| 3 | SS54B | PCM_JLCPCB:D_SMB | D5, D10, D18 |
| 3 | TestPoint_Small | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP1, TP2, TP3 |
| 2 | 100pF | Capacitor_SMD:C_0805_2012Metric | C2, C14 |
| 2 | 1N5819WS | PCM_JLCPCB:D_SOD-323 | D7, D14 |
| 2 | 1N5819WS | Diode_SMD:D_SOD-323 | D17, D20 |
| 2 | 1nF | Capacitor_SMD:C_0805_2012Metric | C13, C25 |
| 2 | 33kΩ | PCM_JLCPCB:R_0805 | R13, R29 |
| 2 | 470uf | Capacitor_SMD:CP_Elec_10x10 | C6, C22 |
| 2 | 470uf 25V | Capacitor_SMD:CP_Elec_10x10.5 | C4, C30 |
| 2 | 47kΩ | PCM_JLCPCB:R_0805 | R24, R50 |
| 2 | 680Ω | PCM_JLCPCB:R_0805 | R30, R69 |
| 2 | BAT54C,215 | PCM_JLCPCB:SOT-23-3_L2.9-W1.6-P1.90-LS2.8-BR | D1, D8 |
| 2 | Green | PCM_JLCPCB:D_0805 | D4, D12 |
| 2 | INA2180A2IDGKR | Package_SO:VSSOP-8_3x3mm_P0.65mm | U6, U12 |
| 2 | INA3221 | Package_DFN_QFN:Texas_RGV0016A_VQFN-16-1EP_4x4mm_P0.65mm_EP2.1x2.1mm | U10, U11 |
| 2 | L_Ferrite | Inductor_SMD:L_1206_3216Metric | L1, L4 |
| 2 | SMBJ6.0CA | PCM_JLCPCB:D_SMB | D3, D11 |
| 2 | TLV1702AIDGKR | Package_SO:Texas_S-PDSO-G8_3x3mm_P0.65mm | U7, U13 |
| 2 | TLV9352 | digikey-footprints:SOIC-8_W3.9mm | U1, U3 |
| 2 | Wire con | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | J3, J5 |
| 2 | Yellow | PCM_JLCPCB:D_0805 | D15, D19 |
| 2 | ~ | 1My_Parts_ Passive:10mm LOGO | 10mm1, 10mm2 |
| 1 | 0Ω | PCM_JLCPCB:R_0805 | R32 |
| 1 | 1.8kΩ | PCM_JLCPCB:R_0805 | R3 |
| 1 | 1000uf 25v | Capacitor_SMD:C_Elec_10x10.2 | C29 |
| 1 | 100nf | Capacitor_SMD:C_0805_2012Metric | C28 |
| 1 | 100pF | PCM_JLCPCB:C_0805 | C26 |
| 1 | 10mohm | PCM_JLCPCB:R_0805 | R64 |
| 1 | 1k | PCM_JLCPCB:R_0805 | R65 |
| 1 | 200m ohms | Resistor_SMD:R_2512_6332Metric | R45 |
| 1 | 200mΩ | Resistor_SMD:R_2512_6332Metric | R19 |
| 1 | 20m ohms | Resistor_SMD:R_2512_6332Metric | R37 |
| 1 | 20mΩ | Resistor_SMD:R_2512_6332Metric | R7 |
| 1 | 3100 | PCM_JLCPCB:R_0805 | R61 |
| 1 | 470uf 50v | Capacitor_SMD:CP_Elec_10x10.5 | C17 |
| 1 | 5 ohms - 4.5amp | Varistor:RV_Disc_D7mm_W4.5mm_P5mm | RT1 |
| 1 | 820Ω | PCM_JLCPCB:R_0805 | R31 |
| 1 | AW9523B | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm | U5 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Right | J6 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical_SMD_Pin1Right | J7 |
| 1 | MDL 5 | Fuse:Fuseholder_Clip-6.3x32mm_Littelfuse_102_Inline_P34.21x7.62mm_D2.54mm_Horizontal | F1 |
| 1 | Red | PCM_JLCPCB:D_0805 | D16 |
| 1 | ~ | 1My_Parts_ Passive:5mm LOGO | 5mm1 |

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Development-Station-Power-Supply
3 channel bench supply with current and voltage plotting

Phil-CIA/Solar-Project-200w
Solar Project 200W is a prototype-first hardware and firmware effort for a 200W-class solar charging system built around a 4S LiFePO4 battery domain.

thebenedict/seattletransit-hardware
Schematic and PCB for a circuit board map of Seattle area public transit.


caesarakalaeii/rgb-badge
The badge to end all badges, cutomizable functions, crazy tight led matrix




It measures 100 × 125 mm and has 2 copper layers, 1.6 mm thick.
235 parts, built around the LMV358IDR, LM2596S-ADJ, AW9523BTQR and PSMN5R2-60YLX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Phil-CIA/Development-Station-Power-Supply repository on GitHub, at the commit this page was made from: the board is hardware/kicad/dsp-regulator-rev-c/DSP-Regulator-RevC.kicad_pcb and its schematic hardware/kicad/archive/DSP Regulator.kicad_sch_before hat.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Phil-CIA before reusing the design.