

Headset orga
This project was made by kicad 10.0. My first personal headset to support my several research in audio or embedded fields
- Size
- 69.8 × 98.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 136
- Nets
- 102
- Pads
- 506
- Tracks, vias
- 72, 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 14 Oct 2026
- Updated
- 14 Oct 2026
Overview
Headset orga is an open-source printed circuit board by Orlandogani, from the Orlandogani/pers-esp32-headset repository on GitHub. It is a 4-layer board of 69.8 × 98.5 mm with 136 parts on 102 nets, routed with 72 tracks and 2 vias.
It is built around the ESP32-S3-WROOM-1-N8, TLV320AIC3104IRHBT and BQ24074RGTR, with the LP5907MFX-3.0, LSM6DSV16X and TLV75518PDBV among its other parts. Its parts include 42 resistors, 39 capacitors, 8 ICs, 6 diodes and 4 connectors. It belongs with the ESP32 boards of this library.
Main components
12ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesTLV320AIC3104IRHBT
VQFN-32(5x5)-40℃~+85℃ 1.1V~3.6V、1.525V~1.95V、2.7V~3.6V 8kHz~96kHz Encoder/decoder Serial、I2C VQFN-32(5x5) Audio Interface ICs ROHSTexas InstrumentsAudio Interface ICsBQ24074RGTR
QFN-16-EP(3x3)-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.2V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementLP5907MFX-3.0
SOT-23-5-40℃~+125℃@(Tj) 1 120mV@(250mA) 12uA 250mA 3V 5.5V 6.5uVrms 82dB@(1kHz) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLSM6DSV16X
LGA-14_2.5x3mmUncategorisedSTMicroelectronicsTLV75518PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 33uA 380mV@(500mA) 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Soft Start、Enable、Thermal Shutdown Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)IM73D122V01
IP57 Dust and Water Resistant Analog XENSIVTM MEMS MicrophoneInfineon TechnologiesUncategorisedSI2302CDS-T1-GE3-ES
SOT-23-55℃~+150℃ 1 N-channel 200pF 20V 28pF 3.3A 35pF 3nC@4.5V 400mW 45mΩ@4.5V、62mΩ@2.5V 700mV N-Channel SOT-23 MOSFETs ROHSElecSuperMOSFETsSIQ-02FVS3
SMD500uA 5V Incremental Straight SMD Rotary Encoders ROHSMitsumi ElectricRotary EncodersSM05B-SRSS-TB
SMD,P=1mm,卧贴-25℃~+85℃ 1 1A 1mm 1x5P 2.9mm 4.32mm 5 50V 5P 7mm Auxiliary Solder Pin Copper alloy PA SH Surface Mount, Right Angle Tin UL94V-0 White SMD,P=1mm,卧贴 Wire To Board Connector ROHSJSTWire To Board ConnectorSMF5V0A-E3-08
SMF(DO-219AB)1 1.12nF 1kW@8/20us 21.7A@10/1000us 5V 5uA 7.1V 9.2V ESD IEC 61000-4-2 Unidirectional SMF(DO-219AB) ESD and Surge Protection (TVS/ESD) ROHSVishay IntertechnologyESD And Surge Protection (TVS/ESD)
Parts
136| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP5, TP6, TP7, TP8, TP9, TP10, TP15, TP16, TP17, TP18, TP19 |
| 12 | 100nF | Capacitor_SMD:C_0402_1005Metric | C13, C21, C25, C26, C27, C29, C31, C32, C41, C42, C45, C46 |
| 6 | 1uF | Capacitor_SMD:C_0402_1005Metric | C22, C35, C37, C38, C39, C40 |
| 6 | 22R | Resistor_SMD:R_0603_1608Metric | R28, R29, R30, R31, R32, R35 |
| 5 | 10K | Resistor_SMD:R_0603_1608Metric | R4, R8, R14, R16, R23 |
| 5 | 10k | Resistor_SMD:R_0402_1005Metric | R15, R38, R39, R40, R45 |
| 5 | 1uF | Capacitor_SMD:C_0603_1608Metric | C8, C17, C18, C19, C20 |
| 4 | 0R | Resistor_SMD:R_0402_1005Metric | R24, R25, R26, R34 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C14, C15, C16, C24 |
| 3 | 100K | Resistor_SMD:R_0603_1608Metric | R10, R19, R22 |
| 3 | 10nF | Capacitor_SMD:C_0402_1005Metric | C34, C43, C44 |
| 3 | 10uF | Capacitor_SMD:C_0402_1005Metric | C28, C30, C33 |
| 3 | MountingHole | orga:MountingHole_2.4mm_M2 | H1, H2, H3 |
| 2 | 0R | Resistor_SMD:R_0603_1608Metric | R18, R33 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric | R17, R21 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R3, R20 |
| 2 | 1M | Resistor_SMD:R_0402_1005Metric | R13, R27 |
| 2 | 4.7K | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 68R | Resistor_SMD:R_0402_1005Metric | R42, R43 |
| 2 | BLM18PG221SN1D | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 2 | IM73D122V | orga:Infineon_PG-LLGA-5-3_IM73D122 | MK1, MK2 |
| 2 | TPD1E10B06 | Diode_SMD:D_0402_1005Metric | D5, D6 |
| 1 | 1.5K | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R37 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 12.288MHz (DNP, ASE not stocked) | Oscillator:Oscillator_SMD_Abracon_ASE-4Pin_3.2x2.5mm | Y1 |
| 1 | 150141M173100 RGB (CA) | LED_SMD:LED_RGB_Wuerth-PLCC4_3.2x2.8mm_150141M173100 | D7 |
| 1 | 1K8 | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 1nF | Capacitor_SMD:C_0402_1005Metric | C36 |
| 1 | 2.2k | Resistor_SMD:R_0603_1608Metric | R36 |
| 1 | 2.2uH Wurth 74438335022 | Inductor_SMD:L_Wuerth_MAPI-3015 | L1 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C23 |
| 1 | 4.7nF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 470R | Resistor_SMD:R_0402_1005Metric | R41 |
| 1 | BAT54CLT3G | Package_TO_SOT_SMD:SOT-23 | D4 |
| 1 | BOOM MIC 3.5mm (SJ2-3593D-SMT) | Connector_Audio:Jack_3.5mm_CUI_SJ2-3593D-SMT_Horizontal | J4 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_EVQP7A | SW2 |
| 1 | BQ24074RGT | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm_ThermalVias | U1 |
| 1 | DBG_TIMING | TestPoint:TestPoint_Pad_D1.0mm | TP14 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U2 |
| 1 | HPL_N | TestPoint:TestPoint_Pad_D1.0mm | TP21 |
| 1 | HPL_P | TestPoint:TestPoint_Pad_D1.0mm | TP20 |
| 1 | HPR_N | TestPoint:TestPoint_Pad_D1.0mm | TP23 |
| 1 | HPR_P | TestPoint:TestPoint_Pad_D1.0mm | TP22 |
| 1 | IM73D122V01 (inner cup) | orga:Infineon_PG-LLGA-5-3_IM73D122 | MK3 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | LP5907MFX-3.0 | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | LSM6DSV16X | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U9 |
| 1 | MFB (side) | Button_Switch_SMD:SW_SPST_EVQP7A | SW4 |
| 1 | POWER (side) | Button_Switch_SMD:SW_SPST_EVQP7A | SW1 |
| 1 | RX0 | TestPoint:TestPoint_Pad_D1.0mm | TP13 |
| 1 | SI2302CDS-T1-GE3 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | SIQ-02FVS3 | lcsc:SW-SMD_SIQ-02FVS3_1 | SW3 |
| 1 | SM05B-SRSS-TB | Connector_JST:JST_SH_SM05B-SRSS-TB_1x05-1MP_P1.00mm_Horizontal | J3 |
| 1 | SMF5V0A-E3-08 | Diode_SMD:D_SMF | D1 |
| 1 | SPARE_IO48 | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | SPK LEFT SM02B-SRSS-G-TB | Connector_JST:JST_SH_SM02B-SRSS-TB_1x02-1MP_P1.00mm_Horizontal | J5 |
| 1 | TLV320AIC3104IRHBT | Package_DFN_QFN:Texas_RHB0032E_VQFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm_ThermalVias | U8 |
| 1 | TLV75518PDBV | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | TPS63001DRCR | Package_SON:Texas_DRC0010J_ThermalVias | U3 |
| 1 | TX0 | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | USB-C (GCT USB4105-GF-A) | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U7 |
Similar boards
- 2 layers49.4 × 56.2 mm

- 4 layers43 × 40 mm

- 4 layers140.6 × 108.1 mm

- 2 layers77 × 150 mm

Vrp mvp one frontside
roach350/vrp_spanaway_hardware
KiCAD design files for the VoLTE Retrofit Project Minimum Viable Product One (Code name: Spanaway)
85 parts - 4 layers40.1 × 60.5 mm

- 4 layers115 × 234.4 mm

- 4 layers63.5 × 165.4 mm

- 2 layers65 × 56 mm

Teamc carrier
SantiBarrios2002/mtp-f26-teamc
MTP F26 (UPC) Team C workspace: radio link budget, RFM69 firmware, protocol simulator
94 parts
Questions
How big is the Headset orga PCB?
It measures 69.8 × 98.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Headset orga use?
136 parts, built around the ESP32-S3-WROOM-1-N8, TLV320AIC3104IRHBT, BQ24074RGTR and LP5907MFX-3.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Headset orga KiCad files?
From the Orlandogani/pers-esp32-headset repository on GitHub, at the commit this page was made from: the board is headset-orga.kicad_pcb and its schematic headset-orga.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Headset orga design in my own project?
Its repository states no licence, so its author keeps all rights: ask Orlandogani before reusing the design.