Skip to the content
12345

LP5907MFX-3.0

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 120mV@(250mA) 12uA 250mA 3V 5.5V 6.5uVrms 82dB@(1kHz) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/LP5907MFX-3.0
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-23-5
Pins
5
In stock
33,607 at JLCPCB (C475492)
Used on
16 open-source boards

Overview

The LP5907MFX-3.0 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃@(Tj) 1 120mV@(250mA) 12uA 250mA 3V 5.5V 6.5uVrms 82dB@(1kHz) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:LP5907MFX-3.0, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 33,607 are in stock at JLCPCB (part C475492). 16 open-source boards in 11 repositories on GitHub use it.

Symbol

1IN2GND3EN5OUT
Regulator_Linear:LP5907MFX-3.0From KiCad's library

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
2.2 V · VIN, recommended operating minimum · p. 4
Supply, most
5.5 V · VIN, recommended operating maximum · p. 4
Supply, absolute maximum
6 V · VIN, absolute maximum · p. 4
Works from
-40 °C · Ambient temperature minimum · p. 4
Works up to
85 °C · Ambient temperature maximum · p. 4
Junction, hottest
150 °C · Junction temperature absolute maximum · p. 4
Takes working
12 µA · Quiescent current typical, VEN = 1.2V, IOUT = 0mA · p. 5
Takes asleep
200 nA · Quiescent current typical, VEN = 0.3V, disabled · p. 5
Gives
250 mA · Continuous output current maximum · p. 4
Current limit
500 mA · Short-circuit current limit typical, TA = 25°C · p. 5
Dropout
250 mV · Dropout maximum, IOUT = 250mA, SOT-23 · p. 5
Junction to air (DBV)
193.4 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to board (DBV)
45.8 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (DBV)
102.1 K/W · Junction-to-case top thermal resistance · p. 5

What it is and has

6
Regulator
250mA, low-noise, low-IQ LDO · p. 1
Protection
Thermal-overload and short-circuit protection · p. 1
Noise bypass capacitor
Not required · p. 1
Remote output capacitor
Placement supported · p. 1
Output voltage tolerance
±2% · p. 1
Output automatic discharge
Internal 230Ω typical pulldown when disabled · p. 11

Around it

1
cap 1µF
between IN and GND; Input capacitor; ceramic. · p. 11

Specifications

53
ParameterConditionsAs printedPage
Input voltage VINOver operating free-air temperature rangemin -0.3 · max 6 V4
Output voltage VOUTMaximum is the lesser of VIN + 0.3V or 6V, per footnote (2)min -0.3 V4
Enable input voltage VENOver operating free-air temperature rangemin -0.3 · max 6 V4
Junction temperature TJMAXmax 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V ratingmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 V ratingmax 1000 V4
Input supply voltage VINmin 2.2 · max 5.5 V4
Enable input voltage VENmin 0 · max 5.5 V4
Output current IOUTmin 0 · max 250 mA4
Junction temperature TJmin -40 · max 125 °C4
Ambient temperature(3) TASubject to power dissipation and thermal resistance deratingmin -40 · max 85 °C4
Junction-to-ambient thermal resistance RθJADBV (SOT-23), 5 pinstyp 193.4 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DBV (SOT-23), 5 pinstyp 102.1 °C/W5
Junction-to-board thermal resistance RθJBDBV (SOT-23), 5 pinstyp 45.8 °C/W5
Junction-to-top characterization parameter ψJTDBV (SOT-23), 5 pinstyp 8.4 °C/W5
Junction-to-board characterization parameter ψJBDBV (SOT-23), 5 pinstyp 45.3 °C/W5
Input voltage VINTA = 25°Cmin 2.2 · max 5.5 V5
Output voltage tolerance ΔVOUTVIN = (VOUT(NOM) + 1V) to 5.5V, IOUT = 1mA to 250mAmin -2 · max 2 %VOUT5
Line regulation ΔVOUTVIN = (VOUT(NOM) + 1V) to 5.5V, IOUT = 1mAtyp 0.02 %/V5
Load regulation ΔVOUTIOUT = 1mA to 250mAtyp 0.001 %/mA5
Load current ILOADSee(4); stable regulated output without load currentmin 0 · max 250 mA5
Maximum output current ILOADmin 250 mA5
Quiescent current(5) IQVEN = 1.2V, IOUT = 0mAtyp 12 · max 25 uA5
Quiescent current(5) IQVEN = 1.2V, IOUT = 250mAtyp 250 · max 425 uA5
Quiescent current(5) IQVEN = 0.3V (disabled)typ 0.2 · max 1 uA5
Ground current(6) IGVEN = 1.2V, IOUT = 0mAtyp 14 uA5
Dropout voltage(7) VDOIOUT = 100mAtyp 50 mV5
Dropout voltage(7) VDOIOUT = 250mA (SOT-23, X2SON packages)max 250 mV5
Short-circuit current limit ISCTA = 25°C(8)min 250 · typ 500 mA5
Power-supply rejection ratio(9) PSRRf = 100Hz, IOUT = 20mAtyp 90 dB5
Power-supply rejection ratio(9) PSRRf = 1kHz, IOUT = 20mAtyp 82 dB5
Power-supply rejection ratio(9) PSRRf = 10kHz, IOUT = 20mAtyp 65 dB5
Power-supply rejection ratio(9) PSRRf = 100kHz, IOUT = 20mAtyp 60 dB5
Output noise voltage(9) eNBW = 10Hz to 100kHz, IOUT = 1mAtyp 10 uVRMS5
Output noise voltage(9) eNBW = 10Hz to 100kHz, IOUT = 250mAtyp 6.5 uVRMS5
Output automatic discharge pulldown resistance RADVEN < VIL (output disabled)typ 230 Ω5
Thermal shutdown TSDTJ risingtyp 160 °C5
Thermal hysteresis TSDTJ falling from shutdowntyp 15 °C5
Low input threshold VILVIN = 2.2V to 5.5V, VEN falling until the output is disabledmax 0.4 V6
High input threshold VIHVIN = 2.2V to 5.5V, VEN rising until the output is enabledmin 1.2 V6
Input current at EN pin(10) IENVEN = 5.5V and VIN = 5.5Vtyp 5.5 uA6
Input current at EN pin(10) IENVEN = 0V and VIN = 5.5Vtyp 0.001 uA6
Line transient(9) ΔVOUTVIN = (VOUT(NOM) + 1V) to (VOUT(NOM) + 1.6V) in 30usmin -1 mV6
Line transient(9) ΔVOUTVIN = (VOUT(NOM) + 1.6V) to (VOUT(NOM) + 1.6V) in 30us, as printedmax 1 mV6
Load transient(9) ΔVOUTIOUT = 1mA to 250mA in 10usmin -40 mV6
Load transient(9) ΔVOUTIOUT = 250mA to 1mA in 10usmax 40 mV6
Overshoot on start-up(9) ΔVOUTStated as a percentage of VOUT(NOM)max 5 %6
Overshoot on start-up with EN(9) ΔVOUTPercentage of VOUT(NOM); VIN = VOUT + 1V to 5.5V, 0.7uF < COUT < 10uF, 0mA < IOUT < 250mA, EN rising until output enabledmax 1 %6
Turn-on time tONFrom VEN > VIH to VOUT = 95% of VOUT(NOM), TA = 25°Ctyp 80 · max 150 us6
Input capacitance(2) CINCapacitance for stability; over operating free-air temperature rangemin 0.7 · typ 1 uF6
Output capacitance(2) COUTCapacitance for stability; over operating free-air temperature rangemin 0.7 · typ 1 · max 10 uF6
Output/input capacitance(2) ESROver operating free-air temperature rangemin 5 · max 500 mΩ6

Pins, by the datasheet

5
1 IN
Input voltage supply; connect a 1uF capacitor at this input. · p. 3
2 GND
Common ground. · p. 3
3 EN
High enables the regulator; low disables it and discharges OUT through an internal 230Ω resistor. An internal 1MΩ pulldown holds the regulator off by default. · p. 3
4 N/C
No internal electrical connection. · p. 3
5 OUT
Regulated output; connect to the load and a minimum 1uF low-ESR capacitor. An internal 230Ω typical pulldown discharges the output during shutdown. · p. 3

Open-source boards using it

16See all 16
  • 4 layers94.6 × 83.4 mmFmcw nightly, the printed circuit board in 3D

    Fmcw nightly

    matthuszagh/fmcw

    6GHz frequency-modulated continuous-wave radar with real-time range detection

    446 parts66Apache-2.0
  • 4 layers106 × 80 mmMainboard, the printed circuit board in 3D

    Mainboard

    PyroVision-ThermalCam/Mainboard

    Mainboard for the PyroVision thermal camera.

    152 parts11GPL-3.0
  • 4 layers43 × 40 mmClock box, the printed circuit board in 3D

    Clock box

    betz-engineering/clock_box

    A handy clock-generator for the FPGA lab.

    95 partsCERN-OHL-P-2.0
  • 2 layers89.9 × 17.8 mmBivalveBit, the printed circuit board in 3D

    BivalveBit

    millerlp/BivalveBit_hardware

    Heart rate and valve gape sensor wearable for oysters and mussels

    58 partsGPL-3.0
  • 4 layers69.8 × 98.5 mmHeadset orga, the printed circuit board in 3D

    Headset orga

    Orlandogani/pers-esp32-headset

    This project was made by kicad 10.0. My first personal headset to support my several research in audio or embedded fields

    136 parts
  • 4 layers72 × 81 mmEffect pedal, the printed circuit board in 3D

    Effect pedal

    PenguinOwl/effect-pedal

    104 parts
  • 4 layers24.5 × 25.8 mmDW1000, the printed circuit board in 3D

    DW1000

    saima-firdaus/FYP_Non_contact_radar

    1. FYP A - matlab simulations

    58 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LP5907MFX-3.0?

Yes. The symbol is Regulator_Linear:LP5907MFX-3.0 and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LP5907MFX-3.0?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the LP5907MFX-3.0 datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LP5907MFX-3.0?

JLCPCB lists it as part C475492, with 33,607 in stock; the sellers' links on this page open their listings.

What can replace the LP5907MFX-3.0?

Parts like it in the library: the TPS7A2030PDBV by Texas Instruments, the TPRT9013-30GB by TECH PUBLIC, the TCR3UF30A,LM(C by Toshiba and the ME6211C30M5G-N by MICRONE. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LP5907MFX-3.0?

16 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.