
USB C female pad
NotUnderi/stm32screen_pcb
PCB designed to fit into a 52mm closure and interface with some car sensors and stuff

PCB designed to fit into a 52mm closure and interface with some car sensors and stuff
Stm32screen is an open-source printed circuit board by NotUnderi, from the NotUnderi/stm32screen_pcb repository on GitHub. It is a 4-layer board with 40 parts on 100 nets, routed with 314 tracks and 52 vias.
It is built around the MAX31856, TS1117BCW33 RPG and SMBJ24A. Its parts include 13 capacitors, 13 resistors, 6 connectors, 3 ICs and 2 diodes. It belongs with the STM32 boards of this library.
PCB designed to fit into a 52mm closure and interface with some car sensors and stuff
10.6.2026
Ordered PCBs from JLCPCB. Changed made to previous version pictured below these new ones are disposing of the USB connector entirely and with it, the SP0503BAHTG TVS diode, adding a user switch, Adding better labels on the silkscreen, slightly better layout, disposing of THT caps. The board will be powered straight from the car's battery, this allows easier installation and decreases cost and complexity.

17.3.2026

| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C13, C14, C15, C16, C17, C19 |
| 6 | 10k | Resistor_SMD:R_1218_3246Metric_Pad1.22x4.75mm_HandSolder | R1, R2, R5, R6, R8, R10 |
| 2 | 10 | Resistor_SMD:R_1218_3246Metric_Pad1.22x4.75mm_HandSolder | R3, R4 |
| 2 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18, C20 |
| 2 | 2.2uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3 |
| 1 | 100uF | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C5 |
| 1 | 10uF | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C1 |
| 1 | 160 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 3.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 1 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | EGT | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | FUSE | Fuse:Fuse_0805_2012Metric_Pad1.15x1.40mm_HandSolder | F1 |
| 1 | GC9A01 | Connector_JST:JST_PH_B7B-PH-K_1x07_P2.00mm_Vertical | J2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | MAX31856 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U3 |
| 1 | NRST | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC9xxG | SW1 |
| 1 | OIL | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | POWER IN | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | PRESS | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | SMBJ24A | Diode_SMD:D_SMB_Handsoldering | D3 |
| 1 | STM32F407VETx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U2 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | TS1117BCW-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | USER | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC9xxG | SW2 |

NotUnderi/stm32screen_pcb
PCB designed to fit into a 52mm closure and interface with some car sensors and stuff

VasilKalchev/8bit-quad.hw
Flight controller PCB for a custom-built quadcopter based on the ATmega328 microcontroller.


matuhac/Ometak
Cílem projektu je navrhnout jednoduchou řídící desku pro včelařský ometák.





IITB-Rocket-Team-Avionics/Ember
Experimental Flight Computer with potential mitigations of previous issues faced by FLYTE and a testbed for new systems.
40 parts, built around the MAX31856, TS1117BCW33 RPG and SMBJ24A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the NotUnderi/stm32screen_pcb repository on GitHub, at the commit this page was made from: the board is stm32screen.kicad_pcb and its schematic USB-C female pad/USB-C female pad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask NotUnderi before reusing the design.