

RA Preamp RevB
Developmental Preamp board with untested bias control.
- Size
- 22.1 × 39.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 23
- Pads
- 131
- Tracks, vias
- 327, 198
- Pours
- 42
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 9 Jun 2026
- Updated
- 9 Jun 2026
Overview
RA Preamp RevB is an open-source printed circuit board by N5BRG, from the N5BRG/RA_Preamp_RevB repository on GitHub. It is a 2-layer board of 22.1 × 39.1 mm with 37 parts on 23 nets, routed with 327 tracks and 198 vias.
It is built around the QPL9547TR7, JSW2-63VHDRG+ and 0402YK220FBWTR, with the 0402CS-18NXGRW, RC0402JR-073K3L and CC0402KRX7R7BB104 among its other parts. Its parts include 18 capacitors, 5 ICs, 4 resistors, 3 connectors and 3 inductors. It belongs with the audio and music boards of this library.
Main components
7QPL9547TR7
DFN-8(2X2)-40℃~+105℃ 0.3dB 100MHz~6GHz 12.2dB 13.5dB 19.5dB 22.7dBm 3.15V~5.25V 39.3dBm 65mA Low-power mode、Linearization design、Bias control circuit DFN-8(2X2) RF Amplifiers ROHSQorvoRF AmplifiersJSW2-63VHDRG+
QFN-12(2x2)-40℃~+85℃ 0.4dB 2.3V~5.5V 5MHz~6GHz 68dB Integrated control logic、Integrated ESD protection QFN-12(2x2) RF Switches ROHSMini-CircuitsRF Switches0402YK220FBWTR
-- Film CapacitorsKyocera AVXFilm Capacitors0402CS-18NXGRW
04020402 Inductors (SMD) ROHSCoilcraftInductors (SMD)RC0402JR-073K3L
UncategorisedUnknown makerCC0402KRX7R7BB104
0402100nF 16V X7R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMTFC0402E50R0BST1
0402-55℃~+155℃ 30V 50mW 50Ω Thin Film Resistor ±0.1% ±25ppm/℃ 0402 Chip Resistor - Surface Mount ROHSVishay IntertechnologyChip Resistor - Surface Mount
README
README.mdRA_Preamp_RevB
Copyright (c) 2026 Robert S. Stricklin Jr
This hardware design is licensed under the CERN Open Hardware License Version 2 - Permissive (CERN-OHL-P-2.0).
You may obtain a copy of the license in the LICENSE file included with this repository.
Overview
This design has not be fabricated and tested. It is being posted as an optional development effort.
This design is a Radio Astronomy Preamplifier intended for operation at 1420 MHz, which is approximately the frequency of the neutral hydrogen spectral line produced by the hyperfine spin-flip transition of hydrogen atoms in space. This signal is commonly referred to as the Hydrogen Line or the 21-centimeter Hydrogen Line.
The goal of this preamplifier is to provide the lowest practical noise figure while amplifying extremely low-level radio signals. Included in the design is a PIN diode switch that allows switching between the antenna input and an alternate path terminated with a precision 50-ohm reference resistor. This approach is similar to the Dicke switching technique developed by Robert H. Dicke in the mid-1940s for microwave radiometry and receiver calibration.
For best performance, the preamplifier is powered from a low-noise 5-volt power supply (5.5 V maximum). The PIN diode switch is controlled by an external voltage of approximately 1.8 to 2.5 volts applied to the control input for the ON state (3.3 V maximum), and 0 V to -20 mV for the OFF state. The analog RF ground and the digital switching ground are separated to minimize the possibility of switching noise coupling into the RF signal path.
This design is a modification of the RA_Preamp_RevA version. The modification is to add a pair of operation amplifiers to monitor the bias voltage of the first RF amplifier and hold this same voltage constant on the other two RF amplifiers on the PCB. To make this addition it was necessary to run some traces under RF signal traces which is normally not a good plan. The idea of maintaining the same bias voltage is an attempt at making all the amplifiers track over temperature. This can be an advantage when the thermal gradients may cause differences in the RF signal path and the 50 ohm reference signal.
The total current required by the preamplifier is approximately 160 mA, although this value may vary somewhat with temperature and component tolerances. At 5 volts and 160 mA, the power dissipation is approximately 800 mW at 25°C, so good thermal management should be considered when mounting the preamplifier in an enclosure.
The PCB is designed to plug into a power and control PCB. However, because the power board is longer, it may be more practical to mount the boards side-by-side if the power board is used. To minimize noise, a low-noise linear voltage regulator is recommended.
A graph showing the noise figure versus frequency, along with the gain of the preamplifier, is included with the project files. These measurements were obtained using an HP 8970B Noise Figure Meter. The 1420 MHz noise figure is 0.46 dB and the gain is 40.11 dB.
Amateur Radio Astronomy
This design was created to support the educational and scientific goals of the Society of Amateur Radio Astronomers (SARA). Additional information about SARA can be found at:
https://www.radio-astronomy.org/
Many of the ideas incorporated into this design were discussed during SARA's regular monthly Zoom meetings and educational activities.
If you enjoy physics, astronomy, radio astronomy, electronics, and scientific experimentation, please consider joining SARA and participating in its programs. SARA is an especially good opportunity for students and young people who are interested in science, engineering, and technology. Most participation is conducted online through video conference meetings.
Acknowledgements
If you use KiCad, please consider making a donation to the project to help support the continuing development and distribution of this outstanding open-source electronic design software.
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 22p | Capacitor_SMD:C_0402_1005Metric | C1, C3, C7, C9, C11, C14, C19 |
| 3 | 100p | Capacitor_SMD:C_0402_1005Metric | C6, C13, C18 |
| 3 | 10p | Capacitor_SMD:C_0402_1005Metric | C4, C10, C15 |
| 3 | 18n | Inductor_SMD:L_0402_1005Metric | L1, L2, L3 |
| 3 | 1u | Capacitor_SMD:C_0402_1005Metric | C5, C12, C17 |
| 3 | QPL9547 | Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.8x1.6mm | U2, U3, U4 |
| 2 | 2000 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H10, H11 |
| 1 | |||
| 1 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 100p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 3.32K | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 50 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | Antenna | Bob:SMA2_WIDE_GND_EdgeMount_Small | J1 |
| 1 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J11 |
| 1 | JSW2-63VHDRG+ | Bob:MT2140_With_polygons_custompads | U1 |
| 1 | SMA | Bob:SMA_WIDE_GND_EdgeMount_Small | J2 |
| 1 | SYBP-1420+ | Bob:PL-308 | FL1 |
| 1 | TLV9002IDDFR | Package_TO_SOT_SMD:SOT-23-8 | U7 |
Similar boards
- 2 layers22.1 × 39.1 mm

- 2 layers25.3 × 33.4 mm

H1 Cantenna
N5BRG/H1_Cantenna_Preamp
Simple small preamp for use with a cantenna feed for dish or disk antenna.
14 parts - 2 layers41.2 × 80 mm

XIAO ePaper Display Board EE04 V1.2
doug-harriman/E-Display
Electronic display for calendars, weather, etc.
176 partsMIT - 2 layers

- 6 layers100 × 62 mm

- 4 layers100 × 100 mm

Iq mod
gallicchio/AMOD-and-RFMOD
The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…
186 parts - 4 layers78 × 59 mm

- 2 layers

Pcbgolf
chilly23/PCBGolf-master-Comma.ai
Compact PCB studies for the comma.ai PCBGolf challenge, including KiCad and EasyEDA designs, BOMs, STEP models, and routing-status reports.
245 partsMIT
Questions
How big is the RA Preamp RevB PCB?
It measures 22.1 × 39.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RA Preamp RevB use?
37 parts, built around the QPL9547TR7, JSW2-63VHDRG+, 0402YK220FBWTR and 0402CS-18NXGRW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RA Preamp RevB KiCad files?
From the N5BRG/RA_Preamp_RevB repository on GitHub, at the commit this page was made from: the board is RA_Preamp_RevB.kicad_pcb and its schematic RA_Preamp_RevB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RA Preamp RevB design in my own project?
Its repository states no licence, so its author keeps all rights: ask N5BRG before reusing the design.