Skip to the content
2 layers22.1 × 39.1 mmRA Preamp RevA, the printed circuit board in 3D

RA Preamp RevA

N5BRG/RA_Preamp_RevA

Copyright (c) 2026 Robert S. Stricklin Jr

Size
22.1 × 39.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
37
Nets
21
Pads
126
Tracks, vias
255, 148
Pours
42
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
7 Jun 2026
Updated
7 Jun 2026

Overview

RA Preamp RevA is an open-source printed circuit board by N5BRG, from the N5BRG/RA_Preamp_RevA repository on GitHub. It is a 2-layer board of 22.1 × 39.1 mm with 37 parts on 21 nets, routed with 255 tracks and 148 vias.

It is built around the QPL9547TR7, JSW2-63VHDRG+ and 0402YK220FBWTR, with the CC0402KRX7R7BB104, 0402CS-18NXGRW and RC0402JR-073K3L among its other parts. Its parts include 20 capacitors, 4 resistors, 4 ICs, 3 connectors and 3 inductors. It belongs with the audio and music boards of this library.

Main components

7

README

README.md

RA_Preamp_RevA

Copyright (c) 2026 Robert S. Stricklin Jr

This hardware design is licensed under the CERN Open Hardware Licence Version 2 - Permissive (CERN-OHL-P-2.0).

You may obtain a copy of the license in the LICENSE file included with this repository.

Overview

This design is a Radio Astronomy Preamplifier intended for operation at 1420 MHz, which is approximately the frequency of the neutral hydrogen spectral line produced by the hyperfine spin-flip transition of hydrogen atoms in space. This signal is commonly referred to as the Hydrogen Line or the 21-centimeter Hydrogen Line.

The goal of this preamplifier is to provide the lowest practical noise figure while amplifying extremely low-level radio signals. Included in the design is a PIN diode switch that allows switching between the antenna input and an alternate path terminated with a precision 50-ohm reference resistor. This approach is similar to the Dicke switching technique developed by Robert H. Dicke in the mid-1940s for microwave radiometry and receiver calibration.

For best performance, the preamplifier is powered from a low-noise 5-volt power supply (5.5 V maximum). The PIN diode switch is controlled by an external voltage of approximately 1.8 to 2.5 volts applied to the control input for the ON state (3.3 V maximum), and 0 V to -20 mV for the OFF state. The analog RF ground and the digital switching ground are separated to minimize the possibility of switching noise coupling into the RF signal path.

The total current required by the preamplifier is approximately 160 mA, although this value may vary somewhat with temperature and component tolerances. At 5 volts and 160 mA, the power dissipation is approximately 800 mW at 25°C, so good thermal management should be considered when mounting the preamplifier in an enclosure.

The PCB is designed to plug into a power and control PCB. However, because the power board is longer, it may be more practical to mount the boards side-by-side if the power board is used. To minimize noise, a low-noise linear voltage regulator is recommended.

A graph showing the noise figure versus frequency, along with the gain of the preamplifier, is included with the project files. These measurements were obtained using an HP 8970B Noise Figure Meter. The 1420 MHz noise figure is 0.46 dB and the gain is 40.11 dB.

Amateur Radio Astronomy

This design was created to support the educational and scientific goals of the Society of Amateur Radio Astronomers (SARA). Additional information about SARA can be found at:

https://www.radio-astronomy.org/

Many of the ideas incorporated into this design were discussed during SARA's regular monthly Zoom meetings and educational activities.

If you enjoy physics, astronomy, radio astronomy, electronics, and scientific experimentation, please consider joining SARA and participating in its programs. SARA is an especially good opportunity for students and young people who are interested in science, engineering, and technology. Most participation is conducted online through video conference meetings.

Acknowledgements

If you use KiCad, please consider making a donation to the project to help support the continuing development and distribution of this outstanding open-source electronic design software.

Parts

37
QtyValueFootprintReferences
722pCapacitor_SMD:C_0402_1005MetricC1, C3, C7, C9, C14, C19, C20
30.1uCapacitor_SMD:C_0402_1005MetricC8, C11, C16
3100pCapacitor_SMD:C_0402_1005MetricC6, C13, C18
310pCapacitor_SMD:C_0402_1005MetricC4, C10, C15
318nInductor_SMD:L_0402_1005MetricL1, L2, L3
31uCapacitor_SMD:C_0402_1005MetricC5, C12, C17
3QPL9547Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.8x1.6mmU2, U3, U4
23.32KResistor_SMD:R_0402_1005MetricR4, R6
2MountingHole_PadMountingHole:MountingHole_2.2mm_M2_DIN965_PadH10, H11
1100Resistor_SMD:R_0402_1005MetricR5
1100pCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC2
150Resistor_SMD:R_0402_1005MetricR3
1AntennaBob:SMA2_WIDE_GND_EdgeMount_SmallJ1
1Conn_01x04_PinConnector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_VerticalJ11
1JSW2-63VHDRG+Bob:MT2140_With_polygons_custompadsU1
1SMABob:SMA_WIDE_GND_EdgeMount_SmallJ2
1SYBP-1420+Bob:PL-308FL1

Similar boards

  • 2 layers22.1 × 39.1 mmRA Preamp RevB, the printed circuit board in 3D

    RA Preamp RevB

    N5BRG/RA_Preamp_RevB

    Developmental Preamp board with untested bias control.

    37 parts
  • 2 layers25.3 × 33.4 mmH1 Cantenna, the printed circuit board in 3D

    H1 Cantenna

    N5BRG/H1_Cantenna_Preamp

    Simple small preamp for use with a cantenna feed for dish or disk antenna.

    14 parts
  • 6 layers100 × 62 mmExpansion board v3, the printed circuit board in 3D

    Expansion board v3

    naizhao/Pilot-Kit-Box-ESP32-P4

    Pilot Kit Box (ESP32-P4 Edition)

    178 parts11MIT
  • 4 layers100 × 100 mmIq mod, the printed circuit board in 3D

    Iq mod

    gallicchio/AMOD-and-RFMOD

    The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…

    186 parts
  • 2 layersPcbgolf, the printed circuit board in 3D

    Pcbgolf

    chilly23/PCBGolf-master-Comma.ai

    Compact PCB studies for the comma.ai PCBGolf challenge, including KiCad and EasyEDA designs, BOMs, STEP models, and routing-status reports.

    245 partsMIT

Questions

How big is the RA Preamp RevA PCB?

It measures 22.1 × 39.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the RA Preamp RevA use?

37 parts, built around the QPL9547TR7, JSW2-63VHDRG+, 0402YK220FBWTR and CC0402KRX7R7BB104. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the RA Preamp RevA KiCad files?

From the N5BRG/RA_Preamp_RevA repository on GitHub, at the commit this page was made from: the board is KiCAD/RA_Preamp_RevA.kicad_pcb and its schematic KiCAD/RA_Preamp_RevA.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the RA Preamp RevA design in my own project?

Its repository states no licence, so its author keeps all rights: ask N5BRG before reusing the design.