Skip to the content
2 layers18 × 37.5 mmTimer, the printed circuit board in 3D

Fully open source high power rocketry flight computers.

Size
18 × 37.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
26
Nets
48
Pads
120
Tracks, vias
217, 22
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
9 Apr 2024
Updated
9 Dec 2025

Overview

Timer is an open-source printed circuit board by Mines-Rocketry-Club, from the Mines-Rocketry-Club/flight-computers repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 18 × 37.5 mm with 26 parts on 48 nets, routed with 217 tracks and 22 vias.

It is built around the ATTINY88-AU, W25Q128JVSIQ and MC3416, with the AS2312, 2RS1-02-G and MB6S among its other parts. Its parts include 7 resistors, 5 ICs, 3 transistors, 3 connectors and 2 capacitors. It belongs with the radio and wireless boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

6

README

README.md

Mines Rocket Club Flight Computer Development

Scope

The series of flight computers produced as part of this project are inteneded to be useable for any low or high power rocketry applications. These will also span a large range of cost in order to provide flight computer capabilities for very high risk and experimental flights. The lowest possible trim level is a CW RF emmiter intended for use with radio direction finding equipment. The highest trim level will provide a platform for executing user space code asynchronously from the main event loop of the flight computer.

Standards

  • No features* will be lost when moving up in trim levels.

*The Screamer's CW Emmiter is lost as the other telemetry hardware on the board can be used to locate the device.

Trim Levels

NameFeaturesWeightCost (2024)
The ScreamerCW RF Emitter5g5$
The Timer3 Axis Accelerometer, Barometric Altimiter, CP1200 Transmitter, 4 Pyro Channels10g20$
The GuesserGPS, Onboard Data Logging, WIFI based configuration15g40$
The KnowerUser Code Execution, High Frequency Data Logging, 8 Pyro Channels20g60$

System Architectures

The Screamer

Usage

This board emits a constant signal at 146.660 MHz. This signal can be recived by many common low-cost trancievers, such as the Baofeng UV-5RA, UV8W, and AR-5RM. With a directional antenna any of these trancievers provides radio direction finding capabilities to the system.

Design

The sysem does not have a microcontroller or any other regualtion system. It consistis of a power supply, based on the and the transmitter, which is a MAX2606 IF Oscillator. This component is not intended to be used to drive an antenna directly, however, the internal 50Ω matching and the -10dBm power output provide enough for this usage. In order to capture the full -10dBm output, a loop antenna must be attached to BOTH of the provided antenna pads. Bare copper wire or thin coat magnet wire is recommened for the antenna. a single loop in the wire should be adequate for most applicatons.

Due to the extremley low power consumption of the system, it can be powered parasitically off of any of the other computers in this series.

Attachement points will be added in the next revisions of each of the boards

  • The Timer
  • The Guesser
  • The Knower

The Timer

Usage
Design

The Guesser

The Knower

License

All hardware contained within this repository is under the TAPR Open Hardware License (OHL), which can be found, in full, in HW_LICENSE. All software contained within this repository is under the GPL, which can be found, in full, in FW_LICENSE.

Parts

26
QtyValueFootprintReferences
510kResistor_SMD:R_0603_1608MetricR3, R4, R5, R6, R7
3AS2312Package_TO_SOT_SMD:SOT-23Q1, Q2, Q3
3MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2, H3
10.47uInductor_SMD:L_0603_1608MetricL1
11-2834019-4locals_but_working_PLEASE:TE_1-2834019-4J2
11.2kResistor_SMD:R_0603_1608MetricR2
1100nCapacitor_SMD:C_0603_1608MetricC2
110uCapacitor_SMD:C_0603_1608MetricC3
12RS1-02-GConnector_PinSocket_2.00mm:PinSocket_1x02_P2.00mm_VerticalJ3
15.36kResistor_SMD:R_0603_1608MetricR1
1ATTINY88-AUPackage_QFP:TQFP-32_7x7mm_P0.8mmU1
1AVR-ISP-6Connector_PinHeader_1.27mm:PinHeader_2x03_P1.27mm_VerticalJ1
1Battery Celllocals_but_working_PLEASE:CONN2_1775469-2_TECBT1
1MB6SPackage_TO_SOT_SMD:TO-269AAD1
1MC3416Package_LGA:Kionix_LGA-12_2x2mm_P0.5mm_LayoutBorder2x4yU3
1MS5607-02BAPackage_LGA:LGA-8_3x5mm_P1.25mmU5
1TPS61033DRLRPackage_TO_SOT_SMD:SOT-583-8U2
1W25Q128JVSPackage_SO:SOIC-8_5.23x5.23mm_P1.27mmU4

More from Mines-Rocketry-Club/flight-computers

4
  • 4 layers24 × 75 mmThe guesser, the printed circuit board in 3D

    The guesser

    Mines-Rocketry-Club/flight-computers

    Fully open source high power rocketry flight computers.

    117 parts7GPL-3.0
  • 4 layers18 × 46.5 mmThe pointer, the printed circuit board in 3D

    The pointer

    Mines-Rocketry-Club/flight-computers

    Fully open source high power rocketry flight computers.

    88 parts7GPL-3.0
  • 4 layers18 × 14 mmScreamer, the printed circuit board in 3D

    Screamer

    Mines-Rocketry-Club/flight-computers

    Fully open source high power rocketry flight computers.

    15 parts7GPL-3.0
  • 2 layers18 × 23.5 mmTimer programmer, the printed circuit board in 3D

    Timer programmer

    Mines-Rocketry-Club/flight-computers

    Fully open source high power rocketry flight computers.

    5 parts7GPL-3.0

Similar boards

  • 2 layers200 × 150 mmBeatsequencer, the printed circuit board in 3D

    Beatsequencer

    meh2481/beatsequencer

    Beat sequencer/soundboard with Adafruit MultiTrellis

    257 partsUnlicense
  • 4 layers80 × 70 mmRobot, the printed circuit board in 3D

    Robot

    tekkura/sr-cad

    All 3D CAD and PCB design files for smartphone-robot project.

    370 partsApache-2.0
  • 2 layers47.9 × 49.6 mmBMP280Tiny, the printed circuit board in 3D

    BMP280Tiny

    danheeks/vario

    paragliding vario with arduino nano, piezo sounder, bmp180 altimeter, 4x Nimh batterys

    45 parts11
  • 2 layers100 × 99.9 mmPanelized, the printed circuit board in 3D

    Panelized

    SamWarmuth/SWSplitFlap

    3D printable split flap display (software/pcb/STLs), for a more detailed split flap project see https://github.com/scottbez1/splitflap

    144 parts4
  • 2 layers89.6 × 59.3 mmC4-blinkenrocket, the printed circuit board in 3D

    C4-blinkenrocket

    cccc/Blastrocket

    A Blinkenrocket adaption with c4 touch made with KiCAD

    26 parts1
  • 2 layers20.3 × 19.3 mmAttiny48, the printed circuit board in 3D

    Attiny48

    joshnuss/attiny48

    Devboard for ATtiny 48/88

    11 parts1
  • 2 layers97 × 23.7 mmHomegreen Node Basic, the printed circuit board in 3D

    Homegreen Node Basic

    pmalessa/homegreen-Node

    The system is based on an inexpensive node, which is able to control up to 3 pumps and can be powered by nearly any conventional powerbank.

    67 parts1
  • 2 layers304.3 × 274 mmRobotont electronics mainboard, the printed circuit board in 3D

    Robotont electronics mainboard

    robotont/robotont-electronics-mainboard

    Unified pcb design for the 3rd generation robotont robot.

    426 parts1

Questions

How big is the Timer PCB?

It measures 18 × 37.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Timer use?

26 parts, built around the ATTINY88-AU, W25Q128JVSIQ, MC3416 and AS2312. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Timer KiCad files?

From the Mines-Rocketry-Club/flight-computers repository on GitHub, at the commit this page was made from: the board is the_timer/timer.kicad_pcb and its schematic the_guesser/Guesser_IO.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Timer design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).