

Mainboard v1.1
- Size
- 93.2 × 57 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 113
- Nets
- 90
- Pads
- 415
- Tracks, vias
- 659, 137
- Pours
- 14
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 20 May 2024
- Updated
- 30 May 2024
Overview
Mainboard v1.1 is an open-source printed circuit board by MarcusOJ, from the MarcusOJ/lora-based-remotecontrol repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 93.2 × 57 mm with 113 parts on 90 nets, routed with 659 tracks and 137 vias.
It is built around the SHT20, TPS61087DRC and TPS63001DRC, with the NX2016SA-32M-EXS00A-CS06465, PRTR5V0U2X and QT3CD-32.768KEZY-T among its other parts. Its parts include 43 capacitors, 22 resistors, 10 inductors, 7 diodes and 7 connectors. It belongs with the computers and single-board computers boards and the STM32 boards of this library.
Main components
6SHT20
Digital I²C temperature / humidity sensor. Low-cost version. Input voltage: 2.1 - 3.6 V Typical accuracy: ±3 %RH and ±0.3 °C Datasheet: https://www.sensirion.com/sht20/SensirionUncategorisedTPS61087DRC
VSON-10-EP(3x3)-40℃~+85℃@(TA) 1 100uA 2.5V~6V 3.2A 3V~18.5V 650kHz、1.2MHz Adjustable Boost Boost Built-in No VSON-10-EP(3x3) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS63001DRC
VSON-10-EP(3x3)-40℃~+85℃@(TA) 1 1.5MHz 1.8V~5.5V 3.3V 50uA Buck-Boost Buck-Boost Built-in Fixed Yes VSON-10-EP(3x3) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersNX2016SA-32M-EXS00A-CS06465
SMD2016-4P10pF 32MHz 60Ω Crystal Oscillator ±10ppm SMD2016-4P Crystals ROHSNDKCrystalsPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)QT3CD-32.768KEZY-T
SMD3215-2PCrystalsQST Products, LLC
README
README.mdlora-based-remotecontrol
Parts
113| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C21, C27, C36, C37, C38, C39, C40, C41, C43 |
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R11, R12, R17, R19, R22, R23 |
| 6 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18, C19, C28, C29, C30, C35 |
| 5 | 10uF 50V | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C23, C24, C25, C26, C31 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R8, R9, R10 |
| 4 | B230A-13-F | Diode_SMD:D_SMA | D1, D2, D4, D5 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R13, R14 |
| 3 | 47pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C7, C13 |
| 3 | 4pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C8, C16, C17 |
| 3 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H4 |
| 2 | 1000k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_FB1, R_FB2 |
| 2 | 100R | Resistor_SMD:R_0603_1608Metric | R18, R24 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C42 |
| 2 | 2.7nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L5, L6 |
| 2 | 5.6pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C12, C14 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D6, D7 |
| 2 | NMOS | Package_TO_SOT_SMD:SOT-23 | Q1, Q4 |
| 2 | PMOS | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_EVQQ2 | SW2, SW4 |
| 1 | 47 uH | Inductor_SMD:L_TDK_SLF6025 | L11 |
| 1 | 1.2nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C22 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_MPPT2 |
| 1 | 156k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 15nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 18650 | custom:BHC-18650-1P | BT1 |
| 1 | 18k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C20 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C33 |
| 1 | 2.2uH | Inductor_SMD:L_Vishay_IHLP-1212 | L10 |
| 1 | 22nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C32 |
| 1 | 22uF | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C34 |
| 1 | 3.01k 1% | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | 3.3pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15 |
| 1 | 3.9pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_FB3 |
| 1 | 3k3 | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | 3pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C11 |
| 1 | 4.7nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | 470nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 47nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5 |
| 1 | 4k7 | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 6.8uH | custom:DR73 | L9 |
| 1 | 674k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_MPPT1 |
| 1 | 68k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 8.2nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L7 |
| 1 | 9.5nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L3 |
| 1 | BAT SW | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | CapSen | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | DNP | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C10 |
| 1 | DNP | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L4 |
| 1 | IO | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J8 |
| 1 | LTC4121 | custom:LTC4121EUD#PBF | U4 |
| 1 | NX2016SA-32M-EXS00A-CS06465 | custom:NX2016SA-32M-EXS00A-CS06465 | Y3 |
| 1 | PCB.SMAFRA.HT | Connector_Coaxial:SMA_Samtec_SMA-J-P-X-ST-EM1_EdgeMount | J1 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D3 |
| 1 | PV | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | QT3CD-32.768KEZY-T | custom:QT3CD-32.768KEZY-T | Y1 |
| 1 | SHT20 | custom:SHT20 | U5 |
| 1 | STM32L072C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U6 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW3 |
| 1 | SX1262 | custom:SX1262 | U1 |
| 1 | TPS61087 | custom:Texas_DRC0010J | U3 |
| 1 | TPS63001 | custom:Texas_DRC0010J | U2 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J3 |
| 1 | Valve | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
More from MarcusOJ/lora-based-remotecontrol
1- 4 layers91 × 28 mm

Similar boards
- 2 layers94.7 × 71.8 mm

IoT Logger B 1.0
WestianPKl/pcb-docs
A collection of custom PCB designs created in KiCAD, centered around the Raspberry Pi Pico (RP2040) platform. Each board is a standalone module that connects to the Main Board and extends its functionality via I2C, SPI…
147 parts - 2 layers26.1 × 36.2 mm

- 4 layers

MAZE SOLVER PCB DESIGN
lkellyw/MAZE-SOLVER-PCB-DESIGN
My first PCB designed with STM32 to solve a maze by line following
86 parts - 2 layers29 × 49.8 mm

- 4 layers40 × 23 mm

- 4 layers55.4 × 63.3 mm

Lora sensor tag
VladimirBioACS/lora-sensor-tag-pcb-project
Simple LoRa humidity and temperature monitoring device, based on the ESP32-Wroom-D SoC module. Repo contains KiCAD 10 project for LoRa Sensor TAG device with external component libs.
147 parts1 - 2 layers10 × 10 mm

Sht20-breakout board
Chromico/sht20-breakout-board
A simple breakout board based on the SHT20 sensor
6 partsMIT - 4 layers29 × 31.5 mm

Questions
How big is the Mainboard v1.1 PCB?
It measures 93.2 × 57 mm and has 4 copper layers, 1.61 mm thick.
What parts does the Mainboard v1.1 use?
113 parts, built around the SHT20, TPS61087DRC, TPS63001DRC and NX2016SA-32M-EXS00A-CS06465. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Mainboard v1.1 KiCad files?
From the MarcusOJ/lora-based-remotecontrol repository on GitHub, at the commit this page was made from: the board is hardware/mainboard_v1.1/mainboard_v1.1.kicad_pcb and its schematic hardware/mainboard_v1.1/mainboard_v1.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Mainboard v1.1 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).