Skip to the content
2 layers50.5 × 52 mmWellerRT Station projekt, the printed circuit board in 3D

A soldering station controller compatible with Weller RT tips

Size
50.5 × 52 mm
Copper layers
2
Thickness
1.6 mm
Parts
45
Nets
28
Pads
119
Tracks, vias
287, 33
Pours
8
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
26 Dec 2019
Updated
26 Dec 2019

Overview

WellerRT Station projekt is an open-source printed circuit board by MarcelMG, from the MarcelMG/DIY-Soldering-Station-Controller repository on GitHub, published under the MIT licence. It is a 2-layer board of 50.5 × 52 mm with 45 parts on 28 nets, routed with 287 tracks and 33 vias.

It is built around the ATTINY24A-PU, MCP607-I/P and L7805, with the BS170 and IRF4905 among its other parts. Its parts include 15 resistors, 10 capacitors, 4 diodes, 3 ICs and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

5

README

README.md

DIY-Soldering-Station-Controller

A soldering station controller compatible with Weller RT active tips The design is kept simple, with a rotary encoder with internal pushbutton to set the temperature and a TM1637 4-digit 7-segment LED display. When the pushbutton is pressed for >3s, the current target temperature is stored as default value in the non-volatile EEPROM memory of the microcontroller. When the iron handle is put in the stand, the iron goes into standby mode and reduces it's temperature to 100°C. Originally I planned to use a hall sensor to detect the handle in the stand, but I chose a simpler solution by connencting an input pin of the microcontroller with internal pullup resistor to the stand. Since the metal part of the iron tip is grounded, it can sets the pin low and thus enables to detect the iron in the stand. solderingstation

The microcontroller used is a Microchip ATTiny24A. The program code just fits barely into the small flash memory (2kB), so a variant like the ATtiny44 (4kB) or 88 (8kB) might be more appropriate. The display is a TM1637 4-digit 7-segment LED display module, those can be found cheaply on ebay etc. One big advantage of these modules is, that they need only 2 GPIO pins to communicate with the display using an I²C-ish interface. The rotary encoder used has an internal pushbutton, the one I used is salvaged from an old radio. The power supply is a also salvaged from an old laptop or similar, it supplies 12V DC at something around 3.6A. The Weller RT tips are rated at 44W max., so a quite beefy power supply is needed. The Weller RT tips use a standard 3,5mm stereo audio jack connector with the following pinout:

  • tip = heating element
  • middle ring = thermocouple sensor
  • sleeve (back ring) = GND

The thermocouple signal is amplified with a low input offset voltage rail-to-rail OpAmp and fed to the microcontrollers internal ADC. The µC's internal bandgap voltage reference is used. Two RC-lowpass filters in the signal path remove noise in the signal. It is important to only measure the thermocouple sensor voltage when the heating element is off, or else erroneous readings will be produced. To achieve this, the heater is controlled with a center-aligned (a.k.a. phase correct) PWM. In the middle of the low-cycle of the PWM, an interrupt triggers an AD-conversion. The PWM duty-cycle is computed with a P-controller to control the temperature. The heating element is switched with a p-MOSFET power transistor. To drive it's gate with 12V from the microcontrollers 5V level, another small nMOSFET is used. A PCB for the design has been designed and manufactured. The microcontroller is programmed via an 6-pin ISP connector. pcb

This is the connection diagram (pinout) of the PCB: pinout_annotated

Parts

45
QtyValueFootprintReferences
710kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR2, R4, R6, R7, R8, R12, R13
510nCapacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mmC1, C2, C3, C4, C5
3100nCapacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mmC8, C9, C10
3MountingHole_3.2mm_M3_DIN965_PadMountingHole:MountingHole_3.2mm_M3_DIN965_Pad ~, ~, ~
2100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR9, R11
21kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR10, R15
2DDiode_THT:D_DO-35_SOD27_P2.54mm_Vertical_AnodeUpD1, D2
110Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR1
1100µCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC6
11MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR3
1220Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR14
1330nCapacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mmC7
15.6kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR5
1ATtiny24A-PUPackage_DIP:DIP-14_W7.62mm_SocketU1
1AVR-ISP-6Connector_IDC:IDC-Header_2x03_P2.54mm_VerticalISP
1BS170Package_TO_SOT_THT:TO-92_InlineQ1
1DrehencoderConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalENCODER
1Halterung_DetektionConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalHALL
1IRF4905Package_TO_SOT_THT:TO-220-3_VerticalQ2
1L7805Package_TO_SOT_THT:TO-220-3_VerticalU3
1LED1Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalLED1
1LED2Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalLED2
1MCP607Package_DIP:DIP-8_W7.62mm_SocketU2
1NetzteilTerminalBlock_RND:TerminalBlock_RND_205-00232_1x02_P5.08mm_HorizontalJ9
1SW_SPSTTerminalBlock_RND:TerminalBlock_RND_205-00232_1x02_P5.08mm_HorizontalSW1
1TM1637_DisplayConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalDISPLAY
1UART_TXConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalUART TX
1Weller RT LoetspitzeTerminalBlock_RND:TerminalBlock_RND_205-00233_1x03_P5.08mm_HorizontalJ6

Similar boards

  • 2 layers30.7 × 57.8 mmOpenturret hat, the printed circuit board in 3D

    Openturret hat

    mrpossoms/openturret

    Opensource designs and software for autonomously aiming gimble

    8 parts1
  • 2 layers26 × 49.5 mmFast fet switch, the printed circuit board in 3D

    Fast fet switch

    charkster/mosfet_switch_board_v1

    MOSFET Switch board which can quickly toggle the switch and then toggle GPIO pins by a programmable delay.

    20 partsMIT
  • 2 layers50.8 × 71.1 mmSmartSwitch1CH, the printed circuit board in 3D

    SmartSwitch1CH

    joelkoz/CommonSens

    A collection of ready to use Signal K devices

    25 parts2
  • 2 layers145 × 80 mmFinal Competition', the printed circuit board in 3D

    Final Competition'

    Omar-Hany00/ESP32-Robotic-Arm-Car

    Custom ESP32-based RC robotic arm car with integrated PCB, motor control, and servo actuation.

    43 parts
  • 2 layers89.8 × 112.8 mmProjekat, the printed circuit board in 3D

    Projekat

    SrdjanEM/True-RMS-voltmeter

    True RMS voltmeter for AC voltage measurments up to 1000 V. Includes ESD protection and overvoltage protection.

    77 parts
  • 2 layers127 × 125.9 mmTARPN Power Board rev3, the printed circuit board in 3D

    TARPN Power Board rev3

    tarpn/tarpn-battery-backup-deluxe

    Battery backup system for TARPN

    94 parts
  • 2 layers100.8 × 76.1 mmPCB Circuito porton, the printed circuit board in 3D

    PCB Circuito porton

    Yadiel017/Microcontroladores

    Clase de microcontroladores -- Yadiel Encarnacion 2024-0209

    35 parts
  • 2 layersSstc v2, the printed circuit board in 3D

    Sstc v2

    hnaderi/sstc

    Musical solid state tesla coil circuit and part design

    67 parts3CC0-1.0

Questions

How big is the WellerRT Station projekt PCB?

It measures 50.5 × 52 mm and has 2 copper layers, 1.6 mm thick.

What parts does the WellerRT Station projekt use?

45 parts, built around the ATTINY24A-PU, MCP607-I/P, L7805 and BS170. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WellerRT Station projekt KiCad files?

From the MarcelMG/DIY-Soldering-Station-Controller repository on GitHub, at the commit this page was made from: the board is hardware/WellerRT_Station_projekt.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the WellerRT Station projekt design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).